RH Baby&child Airin Spindle Crib User manual

11
/
1/9

IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35" (89cm), the crib shall no longer be used,
and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.
2/9

IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB SHALL BE
AT LEAST 27 1/4" X 51 5/8" WITH A THICKNESS
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot exactly follow the instructions
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and the strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing or if there are any signs of damage.
Do not substitute parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15cm in height and, when it
is pushed firmly against any side of this crib, it does not leave a
gap of more than 3cm between the mattress and any part of any
other side of the crib.
3/9

IMPORTANT SAFETY INFORMATION FOR TODDLER AND DAYBEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51 5/8" (1310mm) in
length, 27 1/4" (690mm) in width and 4" (100mm) in thickness, not
exceeding 6" (150mm) in thickness.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or daybed shall be at least 15 months of
age and shall not weigh more than 50 lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months of age.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
4/9

PARTS IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number in which
the part is used.
Step 1 Leg and end panel assembly
End panel and stationary side rail assembly (Page 6)
Step 2 Mattress support arm assembly
Stabilizer rail assembly
Mattress height adjustment (Page 7)
Step 3 Installation of support slat into the end panels (Page 8)
Step 4 Toddler rail assembly (Page 9)
STATIONARY SIDE RAIL
END PANEL
MATTRESS SUPPORT
5/9

STEP 1
LEG AND END PANEL ASSEMBLY STATIONARY
SIDE RAIL AND END PANEL ASSEMBLY
DETAIL A
DETAIL B
DETAIL B-1
DETAIL B-2
HARDWARE FOR STEP 1
(A) 1/4" x 1 11/16" Allen Bolt = 4 pcs
(B) Threaded Rod (M8x100mm) = 8 pcs
Curve Washer = 8 pcs
Lock Washer = 8 pcs
Open Wrench = 1 pc
14 X 90
Hex Nut = 8 pcs
STEP 1.1
Gently lay the end panels on their backs on a clean and
non-abrasive surface.
STEP 1.2
Align and insert the threaded rod of the legs into the holes on
the bottom of the end panels and turn clockwise to tighten. See
DETAIL A.
STEP 1.3
Bring the end panels and stationary side panels into upright
position.
NOTE:
On inside lower faces of both end panels are holes with
pre-installed nuts for the wooden dowels to pass through which
correspond with pre-installed wooden dowels on the stationary
side rails.
STEP 1.4
Fasten the threaded rod through pre-installed nuts on both end
panels. Bring the stationary side rail up to the end panel and
insert the threaded rods through the holes. Once stationary side
rails are set, insert curved washers and lock washers and
fasten these with hexagonal nuts provided. See DETAIL B-1.
STEP 1.5
Attach the upper part of both end panels to the stationary side
rails with Allen head bolts provided, as in DETAIL B-2.
NOTE: DO NOT OVER TIGHTEN.
6/9

(D) 1/4" x 1 1/4" Allen Bolt = 8 pcs
Plain Washer = 8 pcs
Lock Washer = 8 pcs
Hex Nut = 8 pcs
Allen Wrench = 1 pc 11 X 70
Open Wrench = 1 pc
STEP 2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
MATTRESS HEIGHT ADJUSTMENT
HARDWARE FOR STEP 2
DETAIL C
DETAIL D
Allen Bolt (D)
Stabilizer Rail
Allen Bolt (D)
ALlen Wrench
Hex Nut Open Wrench
Lock Washer Plain Washer
Allen Bolt (D)
C
D
STEP 2.1
Lay mattress support flat with stabilizer rail on each side.
NOTE:
On each end of the arm of the mattress support, there is a hole
for the bolt to pass through that corresponds to the holes located
in the frame of the mattress support.
STEP 2.2:
Insert the bolt into the desired hole of the frame through the hole
on the arm support. Fasten the bolt with plain washer, lock
washers & hexagonal nut provided. Repeat procedure on other
arms of the mattress support. See DETAIL C.
WARNING:
Set the mattress support to the desired height by adjusting the
support arms. The mattress support should be at its highest
setting for newborns, then adjusted to the lower positions as the
child grows and becomes mobile. Once the child is able to
stand, the mattress support should be at its lowest position.
STEP 2.3:
Install the stabilizer rail at ends of the arm support, as illustrated
in DETAIL D.
7/9

DETAIL E
STEP 3
INSTALLATION OF STABILIZER RAILS INTO
THE END PANELS
DETAIL F
DETAIL G
HARDWARE FOR STEP 3
(C) 1/4" x 3/4" Allen Bolt = 4 pcs
Lock Washer = 4 pcs
Plain Washer = 4 pcs
Allen Wrench = 1 pc
STEP 3.1
On inside face of both end panels are pre-installed metal brackets, designed
to hold the stabilizer rails. Set both ends of the stabilizer rails into brackets,
as illustrated in DETAIL E.
STEP 3.2
Once the stabilizer rails are set, gently tilt the crib, as illustrated in DETAIL F,
then fasten the stabilizer rails with bolt, lock washer and plain washer
provided, as illustrated in DETAIL G.
8/9

HARDWARE FOR STEP 4
STEP 4
TODDLER RAIL ASSEMBLY
DETAIL I
DETAIL H
DETAIL J
Allen Wrench = 2 pcs
(E) Connector Nut = 2 pcs
(F) Connector Bolt = 2 pcs
Open Wrench = 1 pc
14 X 90
STEP 4.1
Gently tilt the crib and release the bolts underneath the metal brackets
holding the stabilizer rails.
NOTE:
·When converting to toddler bed, loosen all the bolts and nuts that
connect the end panel and stationary side rail. See DETAIL H.
·If mattress support is not in the lowest position, unscrew mattress
support bolts and move to the lowest position.
STEP 4.2
Repeat procedures from STEPS 1.3 - 1.4, substituting one stationary side
Rail with a toddler rail. See DETAIL H.
NOTE:
Fill the top holes on both end panels with bolts (E&F) provided, as in
DETAIL I.
STEP 4.3
Repeat step 3. Installation of stabilizer rails into the end rail panel, as in
DETAIL J.
After assembly, re-tighten all bolts to a snug fit. DO NOT OVER TIGHTEN.
9/9
(PACKED INSIDE TODDLER RAIL BOX)