Little Cottage Hunting Blind User manual

Little Cottage Co.
PO Box 455
Berlin, OH 44610
330-893-4212
www.cottagekits.com
© 2008-2009 Little Cottage Co.
6x6 Hunting Blind Manual
®
Tools Needed:
-Cordless Drill (12V or higher)
-#2 Square Drive Bit
-Hammer
-Tape Measure
-Speed Square

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 1
12
3 4
56
Thank you for purchasing from Little Cottage Co.
To begin locate your 2x4’s for the oor frame.
You will have 6 pieces for the rim, which are cut
on an angle at both ends. (4) 2x4 joists and (2)
4x4 runners
Fasten (6) pieces of rim as shown and secure with
2 1/2” screws (2) per side.
Next install joist as shown. Rims are marked for
joist placement. Secure with (2) 2 1/2” screws on
each end.
Install as shown. Your 2x4 Rim is marked for
4x4 runner placement.
Secure with (2) 2 1/2” screws on each side.

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 2
78
9 10
11 12
Continue with 2 1/2” screws securing 2x4 Floor
into 4x4
runners.
Next make sure all corners measure the same as
shown.
Once all corners measure the same, Fasten the
rest of 2x4 joist into 4x4’s as shown with 2 1/2”
screws.
Next locate CDX plywood ooring with angles
cut on all corners. Plywood is designed to t the
oor.
Secure with 1 1/4” screws 8” on cemter. Continue fastening the oor.

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 3
13 14
15 16
17 18
Next Locate Triangle oor pieces. Secure with 1 1/4” screws.
Locate wall panel with door. Secure with 2 1/2” screws on each corner.
Make sure wall is pushed against the oor before
fastening.
Continue with each wall section.

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 4
19 20
21 22
23 24
Continue with wall and fasten as shown. To secure top plates fasten with 2 1/2” screws
into 2x6 top plate.
There are 6 walls total. Before installing 6th
panel follow instructions on the next picture.
Remove 2x4 from door on the inside as shown.
Fasten all outside corners on top as shown. Fasten bottom into the oor with 1 1/4” screws
every 8 “ to 10”.

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 5
25 26
27 28
29 30
Next install Aluminum corners and fasten with
white nish nails.
Next install small wood strip on top of aluminum
trim with 1 1/4” screws.
Locate roof rafters. The rafters are marked top and bottom. Make
sure top is up and secure with 1 1/2” screw as
shown.
Continue with rafters. Rafters are complete as shown.

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 6
31 32
33 34
35 36
Next lift rafters on top plate as shown. Use angle square and make sure rafter is ush
with outside edge of 2x6 top plate as shown.
Next install triangle roof pieces. Secure with 1
1/4” screws.
Continue with roof.
Install Aluminum Ridge and fasten with white
nish nail.
Continue with Ridge and fasten every 12” to 14”
with white trim nails.

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 7
37 38
39 40
41 42
Next locate metal cap for peak and put on a bead
of caulk.
You will nd a cut in the cap. Insert a bead of
caulk before installing.
Place metal cap on the peak and fasten with white
trim nails as needed.
Continue with trim nails.
Insert a bead of caulk on the bottom edge of the
ridge as shown to keep moisture out.
Insert a bead of caulk on the bottom edge of roof
panel on all 6 sides as shown.

6x6 Hunting Blind Manual
Construction Manual © 2008-2009 Little Cottage Co. Page 8
43 44
45 46
Next locate door handle. Secure with black head screws.
Install D handle on the inside.
Your Hunting blind assembly is complete, paint
as you desire.