Little Cottage Pennfield Cottage User manual

Little Cottage Co.
PO Box 455
Berlin OH 44610
330-893-4212
© 2007 Little Cottage Co.
Cordless drill (12V or higher)•
#2 square drive bit•
Hammer•
6’ step ladder•
Tape measure•
Square utility knife w/ blade•
& hook blade
e Pennfield Cottage
Tools Needed:

This page intentionally left blank.

Construction Manual © 2007 Little Cottage Co. Page 1
e Pennfield Cottage
1
5 6
Locate the 4x4’s and layout per the ooring diagram.
Beginning at the rear corner, measure and mark
1” from outside edge of 2x4. Set abutting 2x4 and
toenail into 4x4 as shown.
Measure along and mark the 2x4 as to set the
underlying 4x4 on a 48” center.
With the perimeter 2x4’s now in place, measure and
mark ends to allow oor trusses to be set on 16”
centers. Hold 2x4’s in place and secure by driving
two (2) 2½” screws inward. Repeat on opposite ends.
Next, measure on 16” centers at underlying trusses
and secure 2x4’s by toenailing a 2½” screw on both
sides as above.
3
2
4
7 8
Thank you for purchasing from Little Cottage Co!
You will nd all components necessary to complete
your Penneld Cottage. Refer to your buy list for
specic contents, which will vary by unit.
1”
Mark on 16” centers
Once all 2x4’s are in place, verify that ooring
structure is square by measuring corner-to-corner
as above. If lengths are not equal, square structure,
measure, and repeat until square.
Once square, you are ready to begin installing oor
sheeting.
Start sheeting at this corner
Set sheeting in place using angles to ensure sheeting
is ush on both sides. Secure in place by driving 1¼”
screws through the sheeting and into the 2x4’s every
eight (8) inches.

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 2
13 14
15 16
9 10
11 12
Continue to set remaining sheeting until the entire
oor is in place.
Locate the rst wall panel and set in place. Ensure
that stud is ush with the edge of oor structure
using an angle. Apply pressure from the outside and
secure using 2½” screw.
Secure at the opposite end in a similar manner as well
as at every stud in between.
Set the next panel in place. Per the inset, ensure a
20” spacing between studs.
Apply pressure to base and secure by driving 2½”
screws along the bottom of 2X studs (see inset). With
the upper 2X’s ush, secure by driving 2½” screws
from both sides.
Locate the strip of siding to be attached below the
front doorway. Set in place, using an angle to ensure
that the top of strip is even with the oor of structure,
and attach using four (4) 1¼” screws.
Set the remaining panel in place, ensuring that the
end (i.e., at corner) is ush with the edge of oor
structure. Then secure as previously shown.
Set the rear wall panels of structure in place and
secure.

Construction Manual © 2007 Little Cottage Co. Page 3
e Pennfield Cottage
1817
24
19
21 22
23
20
Again, locate the strip of siding to be attached below
the adult doorway. Set in place, using an angle to
ensure that the top of strip is even with the oor of
structure. Attach using four (4) 1¼” screws.
Locate the two sections of the left gable end.
Use an angle to ensure base 2X’s are ush and
secure using a 2½” screw
Square the peak of gable as shown and secure using
a 2½” screw.
Then drive a third 2½” screw through the middle of
abutting 2X’s.
Carefully lift assembled gable end into place.
24
Note that both ends of gable must overhang the
innermost edges of the 2X’s by 5½.” Likewise, lower
plate of gable must be ush with the upper plate of
side wall. Secure both ends with 2½” screws.
With the ends secure, apply pressure (inward or
outward, as needed) to ensure abutting side panels
are ush. The secure by driving 2½” screws on both
sides of studs.

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 4
29 30
31 32
25 26
27
Locate the two sections of the left gable end, noting
these sections accommodate a doorway.
Use an angle to ensure base 2X’s are ush and
secure using a 2½” screw
Square the peak of gable as shown and secure using
a 2½” screw.
Then drive a third 2½” screw through the middle of
abutting 2X’s.
Install trim strip around above opening as shown
using four (4) 1¼” zinc screws.
Carefully lift assembled gable end into place.
Verify that gable and lower wall panels are ush (as
above) and secure using a 2½” screw.
Similarly, square the opposite side of doorway
opening and secure.
28

Construction Manual © 2007 Little Cottage Co. Page 5
e Pennfield Cottage
3433
40
35
37
34
39
36
Verify that gable and lower wall panels are ush at
rear of structure and secure using 2½” screw.
Then secure the gable and lower wall panel at the
front of structure. Repeat for the left side wall,
however, there will be no doorway opening.
Support right door opening by attaching three (3) 36”
braces on both sides and along the top.
Now locate the numbered eave plates (for rear wall)
and set in place. Use an angle to verify that plates
are ush along the upper 2X’s of wall. Secure using
2½” screws on both sides of splices and every 18”.
Secure eave plate blocks at each splice (from below).
Note that center blocks will require a 1¼” black
headed screw on both sides of splice while end blocks
are pre-attached and will each require a single screw.
Locate truss components and place on a level
surface. Note that each 2X truss (or rafter)
component is identied as “front” or “rear.”
Square peak of truss ends. Set truss plate in place (i.e., ush with 2X trusses),
and secure using eight (8) 1¼” zinc screws as shown.
Repeat for remaining trusses.
38

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 6
45 46
47 48
41 42
43 44
Locate markings along upper plate of front wall and
set truss in place.
Secure truss to front wall by toenailing two (2) 2½”
screws through the sides and one through the top.
Similarly, set front truss as marked and use an angle
to ensure tip of truss is ush with edge of eave plate
(see inset).
Then secure truss to front eave plate by toenailing two
(2) 2½” screws through the sides and one (1) through
the top. Then set all remaining trusses.
Referring to your roof sheeting diagram, prepare to
set the rst row of OSB sheeting. First, however,
secure plywood strip (8½” from lower edge) along
lower row of sheeting using 1¼” zinc screws.
Set sheeting in place and secure with 1¼” zinc screws
along bottom and side (i.e., at corners and every 8”).
Measure truss to 24” on center, adjust as needed, and
secure sheeting to truss.
Then, install the remainder of the rst row as well as
the remaining front side of roof.
Edge
Plywood strip will
support porch rafters

Construction Manual © 2007 Little Cottage Co. Page 7
e Pennfield Cottage
49
54
51 52
53
50
Install sheeting on the back roof (no plywood strip is
required).
Next, set the rst piece of decking in place, allowing a
one inch (1”) overhang on the front and side. Secure
decking to the underlying 4x4 using two (2) 2½”
screws. Repeat on the opposite end.
1” overhang
Set the second (and subsequent) pieces of decking in
place (see inset), using an angle to ensure ends are
ush. Secure using two (2) 2½” screws at each 4x4.
Locate and assemble one side of the porch railing.
Verify side railing is ush and level with both the front
railing and post. Then secure by driving two (2) 2½”
screws from the underside of side railing.
Secure the top portion of side railing to the post in a
similar manner. Then, repeat on the opposite side of
the porch railing.
Post
Front
Railing Side
railing
55 56
Next, set the right railing structure on the porch decking
1” in from the edge. Abut railing to the main structure
and secured with a 2½” screw. Then toenail post to
decking in a similar manner.
Similarly, toenail a 2½” screw through the front of
post. Then set the left railing structure in place and
secure in a similar manner.

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 8
59
64
60
61 62
63
57 58
Locate porch beam and carefully carry it to the
structure and place atop the porch posts.
While holding the porch beam in place, measure
outward 32⅛” from the wall of structure and mark the
top of post.
Repeat for the opposite post. Locate the porch gable and set in place.
Secure gable to porch beam using two (2) 2½”
screws.
Secure porch gable to plywood strip on roof sheeting
in a similar manner.
Use an angle and apply pressure to siding splice.
Once ush, secure gable to main structure using two
(2) 2½” screws (see inset).
Secure the front of gable to the porch beam using two
(2) 2½” screws.

Construction Manual © 2007 Little Cottage Co. Page 9
e Pennfield Cottage
70
65
67 68
69
66
Set remaining porch rafters in place as marked.
Secure using two (2) 2½” screws both at the porch
beam and on the roof sheeting. Use an angle to
ensure tip of truss is ush with the edge of porch rafter.
With rafters in place, next install porch roof sheeting
per the sheeting diagram provided with your kit.
Then install trim along siding splice using two (2) 1¼”
zinc screws. Repeat on opposite side of porch.
Install corner strips along porch corners using 1¼”
zinc screws every 12 (twelve) inches. Repeat on rear
corners.
Similarly, install fascia trim along the front of porch
using 1¼” zinc screws every 12 (twelve) inches.
Once all trim is installed, set dripedge in place and
secure along the front of porch using 1¼” screws
every two feet (2’).
71 72
Set shorter dripedge section in place, mark and trim
ush with front dripedge, and secure.
Form joint as shown above at bend along the porch
roof/main structure roof. Snip dripedge as needed.

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 10
75
80
76
77 78
79
73 74
Continue to install/secure dripedge along roof. Note
that you will need to snip the dripedge to allow bend
along the ridge (see upper inset).
Once dripedge is in place, snip the sharp edges off at
both corners of the porch.
Per the instructions on the shingle package, begin
shingling roof.
Stagger shingles upward towards ridge.
Continue installing shingles in a staggered manner. Install all remaining shingles on both sides of the roof.
Now locate your dormer components as shown
above.
Begin assembling dormer sections.

Construction Manual © 2007 Little Cottage Co. Page 11
e Pennfield Cottage
86
81
83 84
85
82
Secure side sections using two (2) 1¼” zinc screws
per side.
With the three sections assembled, now measure 1½”
upward from the bottom of dormer’s side wall framing
and mark.
Align dormer rafter with markings and secure using a
2” screw per side.
Attach the rst side of dormer sheeting using 1¼” zinc
screws at each corner.
Repeat on the opposite side of dormer roof. Then
assemble the remaining dormers.
With dormers now assembled, locate the dormer
base framing and measure and mark inward (from
the edge) consistent with the layout diagram provided
with your kit.
87 88
Measure and mark downward from the ridge
consistent with the layout diagram.
Once location is marked, turn over dormer base
framing and run a bead of caulk along bottom (see
inset). Then temporarily secure to the roof using ve
(5) 2½” screws.

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 12
91
96
92
93 94
95
89 90
From the underside of sheeting, drive ve (5) 2½”
screws upward through the sheeting and into the
dormer base framing. Use the temporary screws
(from above) to locate the desired locations.
Then from the outside, remove the temporary screws
and cut-off exposed screw tips protruding from below.
Measure and mark inward from the other side of roof
consistent with the layout diagram.
Measure and mark downward from the ridge
consistent with the layout diagram. Caulk and install
dormer base framing.
With outer dormer base frames in place, measure and
mark the mid-point between them.
Likewise, measure downward from the ridge (per
layout diagram) and mark to set the nal dormer.
Attach as previously described.
Next, set dormers atop dormer framing bases. Secure dormer to dormer framing base using two (2)
1¼” zinc screws base along the front side.

Construction Manual © 2007 Little Cottage Co. Page 13
e Pennfield Cottage
97 98
99 100
101 102
Similarly, drive three (3) 1¼” zinc screws along the
base (and into the dormer framing base) on both
sides of dormer.
Apply pressure to peak of dormer and secure using a
single 1¼” zinc screw on both sides of ridge.
With dormers now secure, following instructions
on shingle packaging to begin shingling dormers.
Measure and snap a chalk line along sheeting for the
rst row of shingles.
Attach rst row of shingles as shown above, cutting
the end along roof line.
Shingle the entire dormer, including the ridge cap. Now attach ridge cap along main roof line per
instructions.
At the joint of dormer and ridge, attach non-dormer
side of shingle while cutting opposite side to t the
dormer’s ridge.
103 104

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 14
Then secure. Continue to shingle along dormer’s ridge.
105 106
107 108
109 110
111 112
Attach trim to both corners of each dormer using 1¼”
black headed screws (2 per side).
Peel protective sheeting from dormer window and set
in place.
Holding window in place, attach window trim using
four (4) 1¼” zinc screws as shown. Repeat for all
dormers.
Locate and set the adult door spacer in place.

Construction Manual © 2007 Little Cottage Co. Page 15
e Pennfield Cottage
114
115 116
117 118
113
Set the lower adult door section in place and secure
using 1¼” black headed screws.
With the lower section of door in place, set the adult
door spacer as shown.
Then install the upper door section using 1¼” black
headed screws.
Set the outside case in place and secure using 1¼”
black headed screws. Note that its base must be
ush with (or slightly inset from) the door’s trim.
On the inside of door, slide pin handle through hole,
align, and secure with 1¼” black headed screws.
Hold front catch in position, verify that it is aligned with
bolt, and tighten using 1¼” black headed screws.
Locate the (front) door spacer bar and set in place.
119 120
Set the lower door section in place and secure using
1¼” black headed screws.

e Pennfield Cottage
Construction Manual © 2007 Little Cottage Co. Page 16
121 122
123 124
125 126
127
Then install the upper door section using 1¼” black
headed screws.
Position wooden latch and secure by driving a 2½”
screw through the center. Screw should be tight
enough to hold latch in place but not too tight as to
prevent it from turning easily.
Attach outside pulls as shown. Similarly, attach inside pull.
Hold shutter in place, centering it within the height of
window. Secure using three (3) 1¼” zinc screws at
top, bottom, and middle.
Hold opposite shutter in place, center it within height
of window, and secure using three (3) 1¼” zinc
screws at top, bottom, and middle.
Finally, center ower box along the bottom of window
and secure by driving three (3) 1¼” zinc screws along
top of inner back side.

Construction Manual © 2007 Little Cottage Co. Page 17
e Pennfield Cottage