Livart LI-02 User manual

A e fuxg SllE"flfirl ICNO$\[
INSTRUCTION MANUAL
Read this booklet thoroughly before using and save it for future reference.
For further infomation, pleme contact: info@lglivart com
@
MODEL: Ll-02

IMPORTANT SAFEGUARDS
Before using the iron, basic precautions should always be followed including:
1. Read all instructions and save after reading.
2. Before using check that the voltage of wall outlet corresponds to the one shown on the rating plate.
3. Burns inay occur from touching hot metal parts, hot water, or steam. Use cautioh when turning steam
irons upside down as there may be hot water in water tank.
4. lf any part is damaged it must be replaced by the manufacturer, an authorized service agent, or a
qualified technician in order to avoid a hazard.
5. Don't operate any appliance with a damaged cord or plug, after the appliance malfunctions, is dropped,
is leaking, or damaged ln any manner. Return the appliance to the nearest authorized service facility for
examination, repair, electrical, or mechanlcal adjustment.
6. Do not let cord hang over edge oftable or hot surface.
7. The plug of power cord must be removed from outlet before water tank is filled with water
8. To protect against a risk of electric shock, do not immerse the iron in water or other liquids.
9. Close supervision is necessary for any appliance being used by or near children.
10. Do not leave iron unattended when connected into power supply or on an ironing board.
11. The iron must be used and rested on a stable surface.
12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervjsion or
instruction concerning use of the appliances by a person responsible for their safety.
13. Childrenshouldbesupervisedtoensurethattheydonotplaywiththeappliance.
14. lf the appliance is provided with a grounded plug, it must be plugged into a grounded wall socket.
15. Do not allow the cord to come into contact with the soleplate when it is hot.
16. Always place or use the appliance on a stable, level and horizontal surface.
17. Unplug iron, put on its heel, and set steam control to "off,', alter ironing, cleaning the appliance,
filling the water tank or leaving the iron unattended, even for a short while.
18. Use of accessories not recommended by the appliance manufacturer may result in fire, electric
shock or injury to persons.
19. Do not operate the iron for other than its intended use. Do not use outdoors.
HOUSEHOLD USE ONLY

KNOWYOUR STEAM IRON
steam shot button .
spraying water button . \
variable steam button
water tank inlet
--- 360" cord brushing
temperature dial
heel rest
spraying water outlet indicatorl ight
soleplate
Steam shot button
Pressing the button instantly provides a powerful shot of steam to eliminate stubborn
wrinkles.
spray button
Pressing the button instantly provides a fine mist spray to dampen hard-to-iron fabrics.
Variable steam button
Move the button to select the desired steam output for each garment, if selecting the 'bff"
position, it indicates ironing without steam.
Water tank inlet
Fill water tank through here. Ensure that level does not pass "MAK level (250m1 / 1 cup).
Nozzle / Spraying Water Outlet
When pressing spray button, water is instantly sprayed from this outlet.
350o Cord bushing
Cord bushing allows free-movement of power cord in any direction with great
maneuverability when ironing.
Temperature dial
Turn the dial to set ironing temperature that varies with the garment changed
lndicator
When indicator light is illuminated, it indicates that the iron is heating up; it willgo out when
it has reached selected temperature. The light cycles on and off during ironing as the iron
operates to maintain the selected temperature.

Soleplate
The stainless steel soleplate can be heated and used by pressing against the garment.
Heel rest
Heel rest keeps the iron stable on the ironing board
USINGYOUR STEAM IRON
Before first use
1. Remove any sticker, protective foil or storage cover from the soleplate.
2. Fill water into the tank, heat up the iron at the maximum temperature setting and iron over a
piece of cloth for several minutes on the purpose of removing any residue on the soleplate.
Note: lt is normal that strange odor comes out from the unit for the first use.
This will cease after a short while.
Operation
1. Hold the iron in a tilted position, then fill filtered/purified water into water tank by
measuring cup, you had better use purified water with less calcium particles and make
sure not to exceed Max level on the tank. ,a\
\- .)
_"_^
,.,
\' /it-
,/.
":zll
.L-/J., ./ _/
-:=:--y_-
:- - ':
Figurel
2.
3.
Figure2
Note:
. &_!.effill the water tank above the MAX level.
. Do not put the perfume, vinegar, starch, descaling agents,
ironing aids, or other chemicals in the water tank.
. lf the tap water in your area is very hard, we advise you to
mix it with an equal amount of distilled water or to use
distilled water only.
After filling, close the tank cover until it clicks-it is now in the correct position.
Connect plug to outlet and turn temperature knob to your desired setting, depending on
the fabric of garment. The indicator light will be illuminated. Refer to Fig.2 and IRONING
TIPS later. Then, set steam on "off" or dry position (you will hear a click) and place the iron
on its heel (See Fig. 4).

Figure3 Figureq
7,
Once soleplate temperature has reached the preset ternperature, indicator lighi will be off,
then set steam knob to your deslred stearn output or dry position and begin ironing.
WARNING: Never touch hot soleplate at ony time belore cooling down!
Press spray button a couple of times to ihoisten the Iaundry if necessary, before spraying
make sure that there ls enough water in water tank.
Steam shot funetion is best used et max temperature, as it helps remove stubborn creases.
Wait a while before using steam shot button again to avoid splattering.
"Steam shot" can also be appiied when holding the iron in a vertical position, so this is
useful for removing creases from hung clothes, curtains, etc.
The iron has an anti-drip function: if ironing garments for a long time, soleplate
temperature will drop and the lron will stop producing steam automatically so that ho
water comes out of the soleplate.
CLEANING AND MAINTENANCE
After ironing
1. Disconnect power supply and empty the water left ln water tank.
2. To dry soleplate: Reeonnect power supply and disconnect after indicator light goes off
3. Let the iron completely cool down, then wipe flakes and any other deposits on the
soleplate with a damp cloth or a non-abrasive (liquid) cleaner.
WARNING:
. Nevertouah hotsoleplate atanytime before it hascooled down!
. To keep the soleplate smooth, you should avoid haid contact with metal obiects.
' Never use a scouring pad, vinegar or other chemicals to clean the soleplate.
Clean the upper part of iron with a damp cloth.
Wind the main cord around the cord storage facility. Always store the emptied iron
horizontally on a stable surface with a cloth protecting the soleplate.
6.
8.
4.
5.

Self-Cleaning function
You should clean the unit regularly based on the hardness of the water and frequency of use.
1. Fill water tank fully and set the temperature selector to "MAX" and steam to "OFE"
2. Connect power plug and indicator light will illuminate, then place iron on heel (Fig.4)
Warning: Never pour vinegar or other liquid cleaners in the tank!
3. Once the light is ofl hold the iron over a sink and put the steam button to "Self Cledn" position (Fig
3), this may require a little force. Steam and boiling water will come out of the soleplate, while
impurities and flakes will be flushed out.
4. Release the button once all the water in the tank has been used up.
Auto-decalcifi cation feature
There is a decalcification box inside the appliance; it absorbs non-soluble calcium, while releasing
soluble sodium ions so water is softened-this slows down the rate of calcium deposits.
IRONINGTIPS
2.
1. Always check first whether a label with.ironing instructions is attached to the article.
Follow these ironing instructions in any case. lf no ironing-instruction label is
provided, but you know the fabric material, please refer to the table below for
d irection.
lf you do not know what kind of fabric an article is made ol determine the right
ironing temperature by ironing a part that will not be visible when you wear of use
the article.
The table below is not applicable to those fabrics through special treatment (e.g.
shining, frill, projecting etc.) Use low temperature for these particular fabrics.
Always at first divide the clothes according to ironing temperatures. Woolen fabrics
and cotton fabrics etc. should be ironed separately.
The iron heats up quicker than cooling down; therefore, you should start ironing the
articles requiring the lowest temperature such as those made of synthetic fiber.
lf the fabric consists of various kinds of fibers, you must always select the lowest
ironing temperature to iron the composltion of those fibers.
Silk and other fabrics that are likely to become shiny should be ironed on the inner
side. To prevent staining, do not spray water straight on silk or other delicate fabrics.
5.
6.
7.

Velvet and other textures that rapidly become shiny should be ironed in one
direction with light pressure applied. Keep the iron moving at all times.
Pure wool fabrics (100% wool) may be ironed with the iron set a steam position.
Preferably set steam control to the maximum position and use a dry cloth as a mat.
Never iron over zip, rivet in the cloth. This will damage the soleplate.
Additional table
Svmbol Fabric Temp. Variable
steam
Steam
shot Spray
Spthetic
fibers/silk
U
i
i
a
:
I
aa
!
!
aal
,
MAY
xx x
\( Wool {x{
'i:l_ Cotton
Linen { { {
Note:
The sl.rnbol means: This arlicle cannot be ironed!
Note: "r/"stands for being able to use.
"x"stands for being NOT being able to use.
ENVIRONMENTALLY FRIENDLY DISPOSAL
You can help protect the environment!
Please remember to respect the local regulations:
hand in the non-working electrical appliances to
an appropriate waste disposal center.
10