Livingchy Soft Opening Life Style User manual

!
WARNING
If the bed is not properly secured to the wall, it may suddenly tip over, resulting in serious injury or death.
Please read this manual carefully before beginning to assemble the bed.
Soft Opening Life Style
Assembly instructions

WARNING
!
SPECIFICATIONS
If the bed is not properly secured to the wall, it may suddenly tip over and cause serious injury or death.
For wood or masonry wall structures, a qualified person must secure the bed to the wall. •
For all other types of walls, a construction professional must secure the bed to the wall in accordance •
with the codes and regulations of the province, state or country where the bed is installed.
The fixing screw must be suitable for the wall composition material where the bed will be fixed. •
The floor and wall structure entirety must be checked before installation. •
Do not open or use the bed if the cabinet moves when opened or if there are any other signs that the •
screws are loose or detached or if the part to which the screws are attached to the wall is damaged or
cracked.
Never remove the wall fixing screws without first removing the bed base and the pistons. •
A qualified person must have the knowledge and tools to locate the wall studs and identify the type of •
wall structure (wood, metal, masonry or other) and properly install the screws into the wall structure.
Skills and tools required include an electronic stud finder, drill and bits, screwdriver, hammer, level, tape
measure and the ability to use these tools correctly.
Read carefully before starting the installation. Keep this manual.
Maximum weight supported by the bed base: 1000 lbs •
Mattress weight: 45 lbs •
Mattress thickness: 10 in •
Minimum ceiling height: 91 in •
Minimum holding force required for each fixation: 100 lbs •
Do not use with folding mattress. •
Soft Opening Life Style 2

WARNING
If you purchased a bed with a sofa, please assemble the podium before starting the assembly of the
Murphy bed.
INTERACTIVE GUIDE
Please open and follow this interactive guide in addition to this assembly manual for an installation
efficient and safe. Scan this QR code to access the interactive guide.

23
22
23
12
13
12
2
1D
1G
3
5
4
15
10
8
18
11
16
17
9
7
6
10
20
21
19
14
Pièces
No. PART DESCRIPTION QTY
1 CA-COD-XX18 Cabinet side L/R 2
2 CA-DED-XX18 Cabinet top 1
3 CA-TRH-XX Top rail 1
4 CA-TRB-XX Buttom rail 2
5 CA-TRC-XX Middle rail 1
6 CA-AP-XX Door stopper 1
7 MA-SC-1130 Support 2
8 MA-PID-XX Bed foot 1
9 MA-TED-XX Headboard 1
10 MA-CODW-XX Bed side R/L 2
11 MA-ST-XX Cross support 4
12 PO-COV3DW-BE Lower exterior door 1
13 PO-COV3DW-BC Lower center door 1
14 MA-SLP Long support 2
15 MA-SLC Notched long support 2
16 HDF-XXVHL-5 Large HDF 3
17 HDF-XXVHE-5 Narrow HDF 2
18 MA-SPO Support de porte 2 L/2S
19 MA-PWH-XX Top part of handle 1
20 MA-PWB-XX Lower part of handle 1
21 MA-PWF-XX Buttom part of handle 1
22 PO-COV3DW-HC High center door 1
23 PO-COV3DW-HE High exterior door 2
Soft Opening Life Style 3

Hardware checklist
PART QTY PART QTY PART QTY
CAM-B-10 44 CAM-D-10X35MM 44 GOU-B-516X118 20
VIS-C-2 41 BOU-H-M6X25MM 12 PAT-CLOU 4
VIS-P-10X34-NOI 46 VIS-W-8X118 20 VIS-P-8X1 20
AMO-BUM 3 VIS-W-8X112 10 CAV-NOI 2
CAV-XXX 22 CAT-NOI 15 FEUTRE 6
100279-2/100279-
2G
1G/1D
100279-1/100279-
1G
1G/1D PIS-PXX 2
PAT-RF-T 1 PAT-RF-U 2 VIS-A-14x138 2
WAS-LONK-14 2 USB 2 ELASTIC 1
FIXATION 2
Reinforcement
Plate
2 VIS-W-8X2 18
VIS-P-8X112 4 VIS-W-8X3 8 VIS-C-70mm 8
Soft Opening Life Style 4

AM
Hardware checklist
PART QTY PART QTY PART QTY
LED Band + wire 1 Extrusion 1 Lens 1
Cap 1 Clip 3 VIS-P-5X12 3
Switch 1 Power supply 1
Soft Opening Life Style 5

Full-size hardware
CAM-D-10X35MM
SOCKET
CAM-B-10
CAM
VIS-C-2
2'' ASSEMBLY SCREW
VIS-P-8X112
FLATHEAD SCREW #8 X 1 1/2''
BOU-H-M6X25MM
BOLT M6X25MM
VIS-A-14X138
SOCKET HEAD CAP SCREW 1/4X1 1/2''
VIS-P-8X1
FLATHEAD SCREW #8X1''
VIS-W-8X1
WASHER HEAD SCREW #8X1''
VIS-W-8X3
WASHER HEAD SCREW #8X3''
VIS-P-10X34-NOI
BLACK FLATHEAD SCREW #10 X 3/4''
VIS-W-8X112
WASHER HEAD SCREW #8X1 1/2''
VIS-W-8X2
WASHER HEAD SCREW #8X2''
WAS-LOCK-14
LOCKING WASHER 1/4
GOU-B-516X118
WOOD DOWEL 5/16'' X 1 1/8''
VIS-C-70mm
70mm ASSEMBLY SCREW
Soft Opening Life Style 6

A
Dowel
1
B
Cam
Arrow aligned
2
B
C
Insert
D
Lock
E
Locked position
Required tools
-Hammer
-Level
-Robertson screwdriver #1, 2, 3 and flathead
-Wrench 10 mm
-Tape measure
-Drill
Two people are required to assemble this bed.
Special remarks
Cam and dowel assembly
3
4 5
Soft Opening Life Style 7

CA-COD-XX18
CA-COD-XX18
100279-2G
100279-2
VIS-P-10x34-NOI
1
1
VIS-C-2
CA-DED
CA-TRH
CA-TRC
CA-COD
CA-COD
CA-TRB
CA-TRC
*
***
*
Edge band position
1
12
3
5
5
4
CAV-XXX
PAT-CLOU
1- Assembling the cabinet
2- Assembling the cabinet
PART VIS-P-10X34-NOI 100279-2G 100279-2
QTY 16 1 1
PART VIS-C-2 CAV-XXX PAT-CLOU
QTY 27 22 4
Soft Opening Life Style 8

Assembly instructions of the podium
3- Assembling the cabinet
2 people required
If you have purchased a bed with sofa please refer to the assembly instructions of
the podium before continuing with the installation.
WARNING
Soft Opening Life Style 9

WARNING
!
If the bed is not properly secured to the wall, it may suddenly tip over and cause serious injury or death.
For wood or masonry wall structures, a qualified person must secure the bed to the wall. •
For all other types of walls, a construction professional must secure the bed to the wall in accordance •
with
the codes and regulations of the province, state or country where the bed is installed.
The fixing screw must be suitable for the wall composition material where the bed will be fixed. •
The floor and wall structure entirety must be checked before installation. •
Do not open or use the bed if the cabinet moves when opened or if there are any other signs that the •
screws are loose or detached or if the part to which the screws are attached to the wall is damaged
or cracked.
Never remove the wall fixing screws without first removing the bed base and the pistons. •
A qualified person must have the knowledge and tools to locate the wall studs and identify the type •
of wall structure (wood, metal, masonry or other) and properly install the screws into the wall structure.
Skills and tools required include an electronic stud finder, drill and bits, screwdriver, hammer, level,
tape measure and the ability to use these tools correctly.
Read carefully before starting the installation. Keep this manual.
WARNING If the bed is not properly secured to the wall, it may suddenly tip over and cause serious injury or
death.
NEVER use drywall plugs or cavity wall anchors •
NEVER attach the wall bed directly to drywall, gypsum board, or any other wall panel. •
ALWAYS attach the wall bed to wood, metal or masonry wall structure. •
ALWAYS use the 8 mounting screws. •
ANCHOR SELECTION AND FIXING INSTRUCTIONS
!
WARNING
Soft Opening Life Style 10

Selection of anchors according to the composition of the wall
The type of anchor depends on the composition of the wall. Follow the steps below to determine the
composition of the wall if it is unknown:
1. Using an electronic stud finder, determine the center of the studs at the future location of the bed.
2. Drill a 3mm pilot hole in the center of a wall stud to determine the composition of the wall structure. Drill
the hole so that it is hidden by the bed rail.
If the bed is not properly secured to the wall, it may suddenly tip over and cause serious injury or
death.
For wood or masonry wall structures, a qualified person must secure the bed to the wall. •
For all other types of walls, a construction professional must secure the bed to the wall in •
accordance with the codes and regulations of the province, state or country where the bed is
installed.
The fixing screw must be suitable for the wall composition material where the bed will be fixed. •
The floor and wall structure entirety must be checked before installation. •
Do not open or use the bed if the cabinet moves when opened or if there are any other signs •
that the screws are loose or detached or if the part to which the screws are attached to the
wall is damaged or cracked.
Never remove the wall fixing screws without first removing the bed base and the pistons. •
A qualified person must have the knowledge and tools to locate the wall studs and identify the •
type of wall structure (wood, metal, masonry or other) and properly install the screws into the
wall structure. Skills and tools required include an electronic stud finder, drill and bits,
screwdriver, hammer, level, tape measure and the ability to use these tools correctly.
!
WARNING
Composition
du mur
Ancrage Ancrage Procédures
Wood
Wood screw #8x3''
VIS-W-8X3
See fixing procedure for
wood studs
Concrete
Concrete screw
3/16''
See fixing procedure for
masonry structures
Soft Opening LifeStyle
11

4-Installing cabinet on wall
4a- Remove the moulding from the wall where the bed will be installed.
4b- Place the bed at the desired location.
*Note that the bed includes two USB outlets, so a nearby power outlet will be necessary. If the power outlet is
not behind the bed, a 5/8'' to 3/4'' diameter hole can be drilled in the side of the cabinet for the passage of the
wire if required.
4c- Place the level on the cabinet and correct the vertical and horizontal as needed. Ensure that the cabinet is
level in both directions otherwise the closure of the bed will be compromised.
Soft Opening Life Style 12

5- Fixing recommandations
* For this step, refer to the procedure corresponding to the composition of the wall on which the bed will be
fixed.
Wood studs
5a (Wood) - Using the stud finder, locate and mark the studs. The studs can be horizontal or vertical.
HARDWARE VIS-W-8X3
QTY 6
REQUIRED TOOLS DRILL STUD FINDER
Soft Opening Life Style 13

Vertical studs
Wood studs
Gypsum
Top rail
CA-TRH
VIS-W-8X2 1/2
Horizontal studs
5''
(128mm)
5''
(128mm)
5''
(128mm)
=
Wood studs
5b (Wood) - Mark the location of the screws in the center of the studs according to the location below.
Centered on stud
5c (Wood) - Screw the 6 screws in the center of the studs according to the location determined in the previous step
until they reach the wall. The screw must be a minimum of 1 1/4'' deep in the wood stud. Use an adjustable
tension drill to avoid overdriving. Never use a hammer drill. Overdriving the crosspiece to the wall may
damage the part and compromise its structural integrity. Breaking the crosspiece can cause the bed to
suddenly tip over, resulting in serious injury or death.
Soft Opening Life Style 14

NOT included
5''
(128mm)
5''
(128mm)
5''
(128mm)
=
5- Fixing recommandations
Masonry and concrete
5a (Masonry) - Using the drill and wood bit, drill the 6 pre-holes on the CA-TRH top crosspiece. Mark the
location of the holes on the masonry.
*Depending on the composition and type of wall, your professional installer will need to validate and select
more appropriate fixings if required.
HARDWARE
Concrete screw 3/16'' x
suitable lenght
REQUIRED TOOLS Drill
Concrete bit
5/32''
Wood bit
1/8''
Soft Opening Life Style 15

Min 1 1/4'' (32mm)
Max 1 3/4'' (44mm
Masonry Wood lath Gypsum
Top rail
CA-TRH
Masonry or concrete
5b- (Masonry) - Move the cabinet to have access to the hole marking.
5c- (Masonry) - Drill through the gypsum and masonry at the 6 locations marked in the previous step using a
hammer drill and a 5/32" diameter masonry bit.
5d- (Masonry) - Replace the cabinet in its location. Screw the 3/16" x suitable length screws through the holes
in the CA-TRH top crosspiece to the wall. Screw until the cabinet is against the wall. Use an
adjustable tension drill to avoid overdriving. Overdriving the crosspiece to the wall may
damage the part and compromise its structural integrity. Breaking the crosspiece can cause
the bed to suddenly tip over, resulting in serious injury or death.
Soft Opening Life Style 16

On either side of the cabinet, pull simultaneously at the sides of the cabinet in an attempt to pull it off the
wall.
If the cabinet remains firmly fixed to the wall: Continue the installation.
If the cabinet comes off the wall: STOP INSTALLATION IMMEDIATELY. Please contact the
customer's service at
1-833-296-3832 for the procedure to follow.
5- Fixing recommandations
Pull test
*Perform the next step to ensure that the bed cabinet is securely anchored to the wall.
Soft Opening Classic 17

CAM-D-10X35mm
PO-COV3DW-HE
PO-COV3DW-HC
PO-WOV3DHEU
PO-WOV3DBEU
PO-COV3DW-BC
PO-COV3DW-BE
22
23
MA-TED
MA-PID
CAM-B-10
D
Locked
6- Assembling hardware on doors
7- Assembling head and foot board
12
12
13
23
9
8
PART CAM-D-10x35mm
QTY 42
PART CAM-B-10
QTY 20
Soft Opening Life Style 18

CAM-B-10
VIS-C-2
MA-CODW
10
WAS-14
100279-1G
100279-1
BOU-H-M6x25mm
D
Locked
8- Assembling bed side
9- Assembling mechanism plate
PART CAM-B-10 VIS-C-2
QTY 22 8
PART BOU-H-M6X25mm WAS-14 100279-1/G
QTY 12 12 1G/1D
Soft Opening Life Style 19