logika WL-ZSPWBPWBPW-PI11-04 User manual

© 2019 Logika Limited
Smart Lookever Camera
WL-ZSPWBPWBPW-PI11-04
Product Manual
Version 1.0

Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
·[e-mail]
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to ensure safe and
proper installation and use.
•Before use, the product must be properly installed as described in this manual by a qualified
technician.
•The product should be used with the supplied accessories.
•Do not disassemble or modify the product.
•Logika is not responsible for any loss due to improper installation or use of this product.
•Please visit our official website at www.logika.nz for more information.
•You can also contact us at the following email address: [e-mail].

Device Layout
IR Lamp
Status
Indicator
Front View Side View
Device ID
QR Code
SET Button
SD Card Slot
Micro-USB
Port
Rear View

Features
•Communication Mode: IEEE 802.15.4 IEEE 802.11 b/g/n.
•Smart gateway and camera.
•Full 1080p HD.
•Infrared night vision, local storage, video recording and playback.
•Two-way voice communication.
•Motion detection and alarm.
•Remote access via the mobile app.
Specifications
Power Supply AC/DC Adapter DC 5V, 1A
Antenna Type Ceramic Antenna, FPC Antenna
Operating Temperature -10°C - +45°
Operating Humidity C
≤95%RH (Noncondensing)
Power Consumption Max 3W
Rotation Angle Pan: 360°, Tilt: > 180° (manual operation)
White Balance/Backlight Compensation/
Self-Adapting Video Transmission
Supported (Auto)
Motion Detection/Snapshot Supported
Resolution 720p
Audio Talkback Function
Image Rollover 180°
Local Storage Up to Micro SD 32G
Infrared Lamp Board
10×Lamp bead (940nm) (IR Lamp without
Visible Red Light)
Night Visual Range Within 5m
Communication Protocol IEEE 802.15.4 IEEE 802.11 b/g/n
Communication Distance
IEEE 802.15.4 500m (visible)
IEEE 802.11 b/n/g 50m (visible)
Network Protocol
TCP/IP, ICMP, HTTP, HTTPS, DHCP, DNS, RTP,
RTSP, RTCP, NTP, UPnP
Wireless Access Wi-Fi
No. of Devices Allowed to Connect
One (black & white) Three (white) Six (blue)
Unlimited (white plus)

Installation Steps
Hardware Installation
There are two options for mounting the camera:
Option A: Place the camera upright on a suitable flat surface.
Option B: Mount the camera on the ceiling. Bear in mind that, as the camera is effectively upside down in this
case, you will need to update the orientation in the device settings in the mobile app, once it has been added
to the system. This ensures that you can view the video in the correct orientation.
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the Logika
Smart Mobile App user guide which will take you through the process of adding smart devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app will walk
you through how to add the device to the system.
Device Category:
Camera
Device Name:
Lookever Camera
Pull the camera off
the magnetic base.
Punch a hole through the
centre of the base and
screw onto the ceiling.
Mount the camera back
onto the base and attach
the power cable.
Wall plug
Screw

Device Functions
Set Up the Lookever Camera as a Zigbee Gateway
In this mode, the camera can act as a Gateway device, allowing addition of other smart devices on
the network. This means that you do not need to use a Logika Gateway device, as this will perform
the same functions.
To do this, follow the instructions below:
Build the Zigbee Network for the First Time (i.e. Enter Gateway Mode)
Press the SET key 6 times in quick succession. You will hear an audible notification that the network
is now active.
Add devices to this Gateway
Press the SET key 4 times in quick succession. An audible notification will sound once this is
successfully done. This Gateway is now in a mode which will allow other devices to connect.
Stop Adding Devices
Press the SET key 3 times. An audible notification will sound and no other devices can now be added.
Quit the Zigbee Network
Press and hold the SET key for 10 seconds. After the audible notification, the Cloud Camera will have
exited the network successfully.

1
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Quit the Zigbee Network procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at [e-mail] with your issue and we will do our utmost to help!