LogoSat LST6100 User manual

LST6100
LogoSat
User Manual
LST6100 Broadcast Satellite Modem
R1.1
V1.0
LogoSat Shaping the future

This page intentionally left blank

LogoSat Proprietary V1.0
Confidentiality: Unrestricted i of 21
Table of Contents
Table of Contents ...............................................................................i
1 Copyright ........................................................................................... 1
2 EU Compliancy Statements ............................................................. 2
2.1 Radio and Telecommunications Terminal Equipment (R&TTE) 5 Directive 1995/5/EC.................. 2
2.2 EMC Information............................................................................................................................................3
2.3 Restriction of Hazardous Substances Directive (RoHS) (Directive 2011/65/EU)..............................4
2.4 Registration, Evaluation and Authorization of Chemicals (REACH).....................................................5
2.5 WEEE – Waste Electrical and Electronic Equipment Directive..............................................................6
3 Safety Regulations ............................................................................7
3.1 Environmental................................................................................................................................................ 8
4 Feedback ............................................................................................ 9
5 About this Manual .......................................................................... 10
5.1 Cautions and Symbols................................................................................................................................10
5.2 Version History and Applicability..............................................................................................................11
5.3 Related Documentation............................................................................................................................. 12
6 Introduction .................................................................................... 13
6.1 Short Description.........................................................................................................................................13
7 Physical Description ....................................................................... 15
7.1 Front Panel Description............................................................................................................................. 15
7.1.1 Display............................................................................................................................................................15
7.1.2 Soft Buttons and Navigation Buttons..................................................................................................... 16
7.1.3 Front Panel Management Interface........................................................................................................ 16
7.1.4 USB Interface................................................................................................................................................16
7.1.5 LED Status Indicators................................................................................................................................. 16
7.2 Back Panel Description...............................................................................................................................17
7.2.1 Power Connector.........................................................................................................................................18
7.2.2 Earth Ground................................................................................................................................................19
7.2.3 Craft Interface.............................................................................................................................................. 19
7.2.4 Alarm Interface............................................................................................................................................ 20
LST6100 Broadcast Satellite Modem
LogoSat

This page intentionally left blank

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 1 of 21
1 Copyright
© March 11, 2022
The material contained in this document is confidential and intended for use only by parties
authorized by LogoSat Cy N.V.
All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a
retrieval system, or transmitted, in any form or by any means whether, electronic, mechan-
ical, or otherwise without the prior written permission of:
LogoSat Cy N.V.
Superstraat 5
9100 Sint-Kristoff, Belgium
tel: [phone]
fax: [phone]
www.LogoSat.eu
[email protected]
Copyright LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 2 of 21
2 EU Compliancy Statements
To Whom it May Concern.
2.1 Radio and Telecommunications Terminal Equip-
ment (R&TTE) 5 Directive 1995/5/EC
We,
Declare that the following product:
• Product number: LST6100
• Type identifier: NTC/2353
to which this declaration relates is in conformity with the essential requirements of European
Union Directive 1999/5/EC Radio and Telecommunication Terminal Equipment Directive
Essential Requirement 3.1(a), 3.1 (b), 3.2.
Done at St-Kristoff, on March 11, 2016
Serge Van Herck,
CEO
LogoSat Cy N.V.
Superstraat 5 B-9100 Sint-Kristoff Belgium.
Tel: [phone]
Fax: [phone]
EU Compliancy Statements LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 3 of 21
2.2 EMC Information
Relevant EMC information (to FCC rules)
This equipment has been tested and was found to comply with the limits for a class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a commer-
cial environment. This equipment generates, uses and radiates radio frequency energy. If not
installed and used in accordance with the instruction manual, it may cause harmful interfer-
ence to radio communications.
Do not operate this equipment in a residential area, as it is likely to cause harmful inter-
ference. When this is the case, you will be required to correct the interference at your own
expense.
EU Compliancy Statements LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 4 of 21
2.3 Restriction of Hazardous Substances Directive (Ro-
HS) (Directive 2011/65/EU)
The undersigned hereby confirms the following statement:
We hereby declare that this equipment is compliant to the RoHS Directive 2011/65/EU.
Done at St-Kristoff, on March 11, 2016
Serge Van Herck,
CEO
LogoSat Cy N.V.
Superstraat 5 B-9100 Sint-Kristoff Belgium.
Tel: [phone]
Fax: [phone]
EU Compliancy Statements LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 5 of 21
2.4 Registration, Evaluation and Authorization of
Chemicals (REACH)
European Regulation N°1907/2006 "REACH" (Registration, Evaluation, and Authorization of
Chemicals), came into force on June 1st, 2007. It aims at regulating the use of the chemical
substances within the European Union.
We are committed to meeting our legal obligations under REACH, as a manufacturer of art-
icles and as a downstream user of chemicals products.
In order to comply with the REACH regulation, LogoSat Cy N.V. has put into place processes
and procedures to ensure implementation and compliance with the regulation, especially the
assessment of the presence of Substances of Very High Concern (SVHC's) and communica-
tion along the supply chain to both suppliers and customers.
All products manufactured by LogoSat Cy N.V. fall under the category of Articles within the
REACH Regulation and none of them present the notion of intentional release of SVHC's,
therefore no obligation of registration applies.
Done at St-Kristoff, on March 11, 2016
Serge Van Herck,
CEO
LogoSat Cy N.V.
Superstraat 5 B-9100 Sint-Kristoff Belgium.
Tel: [phone]
Fax: [phone]
EU Compliancy Statements LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 6 of 21
2.5 WEEE – Waste Electrical and Electronic Equipment
Directive
The undersigned hereby confirms the following statement:
We hereby declare that this equipment is compliant to the WEEE Directive 2012/19/EU.
Done at St-Kristoff, on March 11, 2016
Serge Van Herck,
CEO
LogoSat Cy N.V.
Superstraat 5 B-9100 Sint-Kristoff, Belgium.
Tel: [phone]
Fax: [phone]
EU Compliancy Statements LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 7 of 21
3 Safety Regulations
Please read this chapter before you install and use this equipment.
To ensure your safety, the equipment has been designed to comply with the following safety
standards:
Safety of Information Technology Equipment.
• IEC 60950-1:2006/A11:2009/A1:2010/A12:2011
• EN 60950-1:2006/A11:2009/A1:2010/A12:2011
• UL60950-1, Second Edition
• CSA C22.2 N°. 60950-1-07.Second Edition
Before you start to install and operate the device, please make sure you observe the follow-
ing points:
• The equipment described in this manual is designed to be used by properly trained per-
sonnel only. Only qualified personnel who are aware of hazards involved may adjust,
maintain and repair the exposed equipment.
No operator serviceable parts inside. Refer servicing to qualified personnel.
To prevent electrical shock, do not remove covers.
• To use the equipment correctly and safely, it is essential that both operating and servi-
cing personnel follow generally accepted safety procedures in addition to the safety pre-
cautions specified in this manual. Warning and caution statements and/or symbols are
marked on the equipment when necessary. Whenever it is likely that safety protection is
impaired, immediately switch off the equipment and secure it against unintended opera-
tion. Inform the appropriate servicing authority about the problem. For example, safety
is likely to be impaired if the equipment fails to perform the intended measurements or
shows visible damage.
• The only way to shut down the device is to disconnect the power cable from the power
connector. Therefore make sure that the power cable is accessible and not obstructed
when the device is operational.For more information please refer to section: Power Con-
nector. on page 18
Additional safety requirements for Finland, Norway and Sweden
Telecommunication connections and cable distribution system.
Special conditions apply to the use of this equipment in Finland, Sweden and
Norway due to different earthing arrangements in these countries. Therefore it
is essential that the installation is done by authorized personnel and according
to the national requirements only.
This equipment is specified for use in a restricted access location only, where
equipotential bonding has been applied and which has provision for a perman-
ently connected protective earthing conductor.
A protective earthing conductor must be installed by a Service Person.
Safety Regulations LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 8 of 21
Additional safety requirements for Norway and Sweden
Equipment connected to the protective earthing of the building installation
through the mains connection or through other equipment with a connection
to protective earthing - and to a cable distribution system using coaxial cable,
may in some circumstances create a fire hazard. Connection to a cable distribu-
tion system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)."
NOTE: In Norway, due to regulation for installations of cable distribution sys-
tems, and in Sweden, a galvanic isolator shall provide electrical insulation below
5 MHz. The insulation shall withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz
or 60 Hz, for 1 min.
Translation to Norwegian:
Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet
jordtilkoplet utstyr - og er tilkoplet et kabel-TV nett, kan forårsake brann-
fare. For å unngå dette skal det ved tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom utstyret og kabel-TV nettet.
Translation to Swedish:
"Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via
annan utrustning och samtidigt är kopplad till kabel-TV nät kan i vissa fall med-
fõra risk fõr brand. Fõr att undvika detta skall vid anslutning av utrustningen till
kabel-TV nät galvanisk isolator finnas mellan utrustningen och kabel-TV nätet."
3.1 Environmental
Operating the equipment in an environment other than that stated in the specifications also
invalidates the safety compliance.
Do not use the equipment in an environment in which the unit is exposed to:
• Unpressurized altitudes higher than 2000 meters;
• Extreme temperatures outside the stated operating range operating temperature
range 0 to + 50°C;
• Excessive dust;
• Moist or humid atmosphere above 85% RH;
• Excessive vibration;
• Flammable gases;
• Corrosive or explosive atmospheres;
• Direct sunlight.
Use a slightly damp cloth to clean the casing of the equipment. Do not use any
cleaning liquids containing alcohol, methylated spirit or ammonia etc.
Safety Regulations LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 9 of 21
4 Feedback
LogoSat encourages your comments concerning this document. We are committed to provid-
ing documentation that meets your needs .
Please send any comments by contacting us at .
Please include document and any comment, error found or suggestion for improvement you
have regarding this document.
Feedback LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 10 of 21
5 About this Manual
This document is intended to help you to
• Understand the different possibilities of the LST6100 Broadcast Satellite Modem;
• Understand the basic features of the LST6100 Broadcast Satellite Modem;
• Find your way connecting and configuring the LST6100 Broadcast Satellite Modem.
5.1 Cautions and Symbols
The following symbols appear in this manual:
A caution message indicates a hazardous situation that, if not avoided, may
result in minor or moderate injury. It may also refer to a procedure or practice
that, if not correctly followed, could result in equipment damage or destruction.
A hint message indicates information for the proper operation of your equip-
ment, including helpful hints, shortcuts or important reminders.
A reference message is used to direct to a location in a document with related
document or a web-link.
About this Manual LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 11 of 21
5.2 Version History and Applicability
Document Version Date Subject Comment
1.0 March 2016 LST6100 Broad-
cast Satellite
Modem
Initial version.
About this Manual LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 12 of 21
5.3 Related Documentation
• The LST6100 Broadcast Satellite Modem Reference Manual describes the parameters avail-
able in the device;
• Device leaflet containing the specifications (We refer to http://www.LogoSat.eu );
• The System Integration Guide for LST6100 describes how to integrate the device into a
network management environment;
The related documentation can be found on the CD-ROM that is delivered
together with the device.
About this Manual LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 13 of 21
6 Introduction
6.1 Short Description
The LogoSat LST6100 Broadcast Satellite Modem is the next generation DVB-S2 and DVB-S
modem specifically designed for broadcast applications. The modem supports the S2 Exten-
sions to achieve barrier-breaking efficiency. This release R2.0 supports multistream demodu-
lation. From release R2.1 onwards, the unit can act as a modulator, demodulator or modem.
As a modulator, it is the best fit for broadcast direct-to-home, primary distribution to head-
ends and contribution of television and radio content. As a modem or demodulator, it is typ-
ically installed in head-ends or at both sides of a contribution link. The LST6100 can be used
in conjunction with set-top boxes, professional IRD’s or professional satellite demodulators
such as the LogoSat AZ910.
Delivering the Highest Uptime for Vital Links
Uptime and reliability are essential in the design of the modem, taking a vital role in the satel-
lite network. Input source redundancy and the shortest redundancy switch-over times of
modems, operating both in 1+1 and N+1 topologies, are setting the standard in our industry.
Advanced capabilities are built in such as a built-in MPEG Transport Stream analyser, support
of SMPTE 2022 FEC at the GbE inputs (for distributed IP headends), and native support of Car-
rier ID according to the new DVB standard as well as in the transport stream NIT Table. Spe-
cial care was taken to cope with jittery transport stream over IP inputs. The 6 ASI ports are
programmable as inputs or outputs allowing for monitoring as well as operational ASI ports.
Get the Best Performance and Lower your Costs
The Broadcast Satellite Modem performs among the best, offering unmatched bandwidth
efficiency optimization options, thereby lowering overall Total Cost of Ownership. The fully
automated operation of LogoSat´s field-proven Equalink® pre-distortion technology, provid-
ing up to 10% bandwidth gains, is now available for any satellite transmission application.
Clean Channel TechnologyTM, in combination with S2 Extensions, improve satellite efficiency
by up to 15%, thereby enabling much smaller carrier spacing. Maximum symbol rates up
to 72 Mbaud and modulations up to 64APSK (S2 extensions) combined with VCM (Variable
Coding and Modulation) allow for maximum throughput in large contribution links.The unit
allows transmitting and receiving simultaneously up to four transport stream(s) in full com-
pliance with the DVB standards. At the output of the Broadcast Satellite Modem, the signal is
available in IF or extended L-band (950 MHz-2150 MHz), providing a compact and cost effect-
ive solution. A switchable 10 MHz reference signal and optional 24V or 48V DC for an out-
door BUC is multiplexed on the L-band interface. The input is dual L-band or as an option
70/140MHz and single L-band.
The Broadcast Satellite Modem can be easily monitored and controlled via a comprehensive
front panel menu, advanced web GUI as well as via SNMP protocol. This enables easy integra-
tion into any industry-standard EMS/NMS system.
Evolve Towards Tomorrow's Technology
Built upon flexible and latest generation programmable technology, the LST6100 Broadcast
Satellite Modem is a future-proof building block that lets any satellite network evolve to the
next level of capabilities. A scalable, pay-as-you-grow, licensing and software upgrade mech-
Introduction LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 14 of 21
anism facilitates the launch of new services, or last minute network design changes, without
rebuilding the entire network infrastructure. Migration from ASI to GbE and IF to L-band is
facilitated by simple in-field installation of license keys. Migration of standard distribution
links towards S2 Extensions can be as simple as inserting a LST6100 modem in the head-ends
while keeping the installed base of IRDs.
Additional capabilities such as DVB-S2 extensions and others are anticipated to become avail-
able on the platform as the standardization efforts materialise in the near future. The brand
new DVB-CID carrier identifier is already available as a software option on the LST6100.
Introduction LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 15 of 21
7 Physical Description
7.1 Front Panel Description
The device can be configured, controlled and monitored using the front panel. The front
panel consists out of the following parts.
For more information please refer to section: How to Use the Front Panel.
7.1.1 Display
The display consists of a 32 x 240 pixels LCD screen.
• The top rows indicates the tree menu pane;
• The bottom row indicates the root menu pane.
Menu Tree
The device management model is designed as a menu tree. The menu tree shows the organ-
ization of the parameters in the device. The tree is built up out of a root, branches, sub
branches and leafs.
• Root: represents the complete device configuration;
• Branch/Sub branch: represents functional blocks that group leafs/parameters that are
closely related to one another;
• Leafs: the leafs represent the parameters or commands that are used to perform a config-
uration.
Physical Description LST6100 Broadcast Satellite Modem
LogoSat

LogoSat Proprietary V1.0
Confidentiality: Unrestricted 16 of 21
7.1.2 Soft Buttons and Navigation Buttons
Use the navigation button and soft buttons to navigate through the menu tree.
• The function of the soft buttons varies depending on the context. Their meaning is defined
by the menu pane block setting atop of each button;
• Use the navigation buttons for navigating through the Tree menu pane;
• Use the OK button to confirm a selection;
• Use the ESC button to ignore a selection and to go up in the menu tree.
7.1.3 Front Panel Management Interface
The management interface allows the system administrators to manage the LST6100 Broad-
cast Satellite Modem and monitor its operation.
Note that this interface is disabled by default.
This connector has the same function as the management interface(s)
on the back panel.
The management can also be done by using the GUI, CLI or SNMP.
7.1.4 USB Interface
The USB interface is a flash drive connector for future use.
7.1.5 LED Status Indicators
Physical Description LST6100 Broadcast Satellite Modem
LogoSat