Lomanco LomanCool 2000 User manual

1.800.643.5596 • Lomanco, Inc. • lomanco.com Subscribe on
YouTube
Find us on
Facebook
LomanCoolTM 2000
Power Vent Installation Instructions
INSTALLATION
1. Determine approximately where on
your roof you will place your Power
Ventilator.
• At the highest point in your
attic or air space. Best if
centered on roof length, and
less conspicuous if placed on
side away from street.
• IMPORTANT: Keep the highest
part of the dome lower than
the ridge line to ensure that
the dome's edge is NOT above
ridge line. (Typically, the center
of the vent should be about 24
inches down from the ridge.)
• Establish your position with
accuracy (because you will
want to duplicate it inside your
attic) by measuring down from
the ridge and over from the
roof edge.
2. Working now from the inside,
mark your planned opening (as
you established position when on
roof) and relocate your position to
be centered between two rafters.
Drive a nail into the roof so that
it can be easily found when you
return to the roof. Before you return
to the roof, be sure that you have:
(a) string or compass, (b) drill and drill
bit, (c) keyhole or electric jig (saber)
saw with a sharp coarse blade, (d)
ventilator and base, (e) roong nails
and hammer, and (f) roong cement
and applicator.
3. Using the nail driven from the inside
as center, scribe a 14” diameter circle
using string or compass. Care should
be taken not to make the hole too
large.
4. Drill a starting hole for sawing inside
the scribed circle.
5. Starting in the drilled hole, cut circular
opening, following the scribed line.
Use either keyhole or an electric jig
(saber) saw with a sharp coarse blade
to cut shingles and roof boards at
one time. If you do not have a coarse
blade, cut away shingles inside the
circle with utility knife before cutting
roof boards.
6. Carefully remove roong nails from
top row of shingles so that the
ashing of the ventilator will slide
under top row.
Slide ventilator carefully into place
with arrow pointing up, letting
thermostat hang down into opening.
Fasten the aluminum base to roof
boards with roong nails. Keep heads
of nails under shingles wherever
possible.
7. Finish the exterior mounting by
sealing all seams and nails with
roong cement. Use cement
also to fasten down loose edges
of shingles. Return to the attic.
You now have to mount the
thermostat and connect the wiring.
20500_0717
WARNING  TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power o at
service panel and lock service panel to prevent power
from being switched on accidentally. When the service
panel cannot be locked, securely fasten a prominent
warning device, such as a tag to the service panel.
C. Installation work and electrical wiring must be done
by qualied person(s) in accordance with all applicable
codes and standards, including re-rated construction.
D. Sucient air is needed for proper combustion and
exhausting of gases through the ue (chimney) of fuel-
burning equipment to prevent back drafting. Follow
the heating equipment manufacturer’s guide lines and
safety standards, such as those published by the National
Fire Protection Association (NFPA) and the American
Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
E. When cutting or drilling into wall or ceiling, do not
damage electrical wiring or other hidden utilities.
F. Ducted fans must always be vented to the outdoors.
G. If this unit is to be installed over a tub or shower, it must
be marked as appropriate for the application.
H. NEVER - place a switch where it can be reached from a
tub or a shower.
CAUTION  For general ventilating use only. Do not use
to exhaust hazardous or explosive materials and vapors.
CAUTION This unit has an unguarded fan blade. Do not
use in locations readily accessible to people or animals.
This fan is intended for use facing an unoccupied space
only.
Be sure your fan is properly installed.Your fan is designed
to operate on 120 VAC 60 Hz.
Sharp edges are exposed during installation. Use gloves
and other safety equipment to avoid accidents.
WARNING  To reduce the risk of re or electric shock,
do not use this fan with any solid state speed control.
IMPORTANT
With the power vent installed, at least 768 square inches
of inlet area must be provided.
OPERATION
Your ventilator will operate automatically as needed.
The adjustable thermostat has been set at the factory
to come on at 100°F., o at 85°F. The motor has been
permanently lubricated and does not require additional
lubrication.

1.800.643.5596 • Lomanco, Inc. • lomanco.com Subscribe on
YouTube
Find us on
Facebook
NOTE:If the dome is removed for
any reason, torque the mounting
screw to a maximum of 60 inch-
pounds (+/- 5) when reinstalled.
CAUTION - DO NOT OVERTIGHTEN
8. Position thermostat base high (in
the warmest part of the air space)
and above the ventilator opening.
Make sure that exible cable does
not touch the roof or rafters. (This
will eliminate vibration noise.)
The thermostat is a delicate
instrument, use screws instead of
nails when fastening bracket to roof
rafter.
Your Lomanco Power Ventilator
MUST be wired as shown. Make all
connections inside the thermostat
box. Connect white (neutral) wire
from a power supply to white wire
on motor. Connect black (hot) wire
from power supply to black wire
on the thermostat and black wire
on switch. The other black wire on
the thermostat and black wire on
switch have been connected to
the black wire on the motor at the
factory but should be checked to
ensure a good tight connection.
The ground wire from the supply
should be connected to the ground
wire from the thermostat box.
9. WARNING! Turn o power before
connecting power wires to ventilator.
Your power feed wire should be 14
gauge or larger wire size (two wires
plus ground). Take from thermostat
box and bring to power distribution
panel. Feed through bushing and
connect to 15-amp circuit breaker.
• Black to circuit breaker
• White to neutral base
• Plain to ground base
Recheck your connections then
turn the power on. You should
now enjoy the advantages of a
Power Ventilator, operating as the
thermostat demands.
A test switch has been provided.
To make sure your Lomanco Power
Ventilator is operating properly,
simply “PUSH TO TEST.” Caution
should be taken to ensure that no
body parts come in contact with any
of the vent’s moving parts during
this test.
NOTE: To control humidity in your
attic, a humidistat is also available.
LIMITED WARRANTY
Lomanco, Inc. Warrants this product for ve (5) years against any defects due to workmanship, parts or mechanical failure.
For warranty service the defective part must be sent, freight prepaid to Lomanco Inc. P.O. Box 519, 2101 West Main Street,
Jacksonville, Arkansas 72076. If the part is found to be defective it will be replaced with a new part at no charge and returned,
freight prepaid. This warranty does not include replacement due to destructive storms or labor cost incurred in the removal
of any defective part/product or installation of the new part/product. Online registration of the product at www.lomanco.
com within ten (10) days of the initial installation of the product is a condition precedent to warranty coverage. ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ALSO LIMITED IN DURATION TO FIVE
(5) YEARS. CONSEQUENTIAL DAMAGES TO PROPERTY RESULTING FROM A BREACH OF ANY WARRANTY MENTIONED HEREIN
ARE EXPRESSLY EXCLUDED. Some states do not allow limitations on how long an implied warranty lasts or do not allow
exclusion or limitation of consequential damages, so the above limitation may not apply to you. The warranty gives you
specic legal rights and you may also have other rights which
vary from state to state.
CSA
Approved
®
20500_0717
Parts and accessories available online at lomanco.com
Texas Department of
Insurance “Windstorm”
Approved
ONLINE WARRANTY REGISTRATION
Please ll out the online form at lomanco.com
to complete your warranty registration. If for
any reason you are unable to register your
product online please call 1.800.643.5596 and
we will assist you. Purchase and install date
information will be required.
LomanCoolTM 2000
Power Vent Installation Instructions
THREE
MUST
DO
Steps
to attic ventilation
Install all Exhaust Ventilation at the SAME HEIGHT with-
in a common attic area.
Installation of exhaust vents at more than one level on a roof allows
the upper exhaust vent to pull air in from lower exhaust vents rather
than from the intake vents. Intake air must come from intake vents
located near the lower part of the attic space to properly ventilate
the total attic area and eliminate weather infiltration.
Install ONLY ONE TYPE of Exhaust Ventilation within a
common attic area.
Exhaust Vents pull air from the easiest intake source. Vent types
cannot be mixed. The use of different types of exhaust vents could
make one of the vents act as intake for the other. Intake air must
come from intake vents located near the lower part of the attic
space to properly ventilate the total attic area and eliminate
weather infiltration.
Install a BALANCED SYSTEM of Intake and Exhaust
Ventilation.
50% Intake Ventilation - Intake vents located near the lower part
of the attic area are required to balance out your ventilation system.
50% Exhaust Ventilation - Use a Lomanco Ventilation Selector
guide, the calculators at lomanco.com, or the Lomanco Vent
Selector App to determine the number of vents needed to properly
ventilate an attic to meet the minimum code ventilation standard.
1
2
3