LOMI XO-9917 User manual

Sunrise Alarm Clock with Himalayan Salt Lamp
& Wireless Charger
Instrucon Manual
XO-9917
•XO-9917 Sunrise Alarm Clock with WirelessCharger (x1)
•Power Cable (x1)
•User Manual (x1)
•This product is NOT a toy, keep away from children and pets.
•Only use the device according to the instrucons in this manual. Never
use the device for anything other than its intended purpose.
•This device is NOT a substute for proper medical equipment or
aenon.
•ONLY use the supplied power cable.
•Do not open this product or aempt to repair the unit yourself if it is
not working properly. Doing so risks fire, shock or injury.
•When not in use, the device should be stored in a dry, cool locaon,
away from sources of water or heat.
•Do not expose device or power cable to extreme temperatures (heat or
cold), open flames, humid or wet condions.
•Do not submerge in water. Do not use in a locaon where the device or
power cable could fall into liquid.
•Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
•Do not use if device or power cable is damaged. If device or power
cable is damaged, it MUST be serviced or replaced by the manufacturer
or its service agent before using again.
•Aachments on the back of your device can impede effecveness of
the wireless charger, and lead to overheang. Remove aachments
from your device before charging on this wireless charger.
Safety Precauons
In the Box
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS
MANUAL
Seng the Alarm
•Press the [SET] buon unl the alarm me is displayed.
•Press the [DOWN] buon to turn the alarm ON or OFF. The dot in
the lower lecorner of the clock display will light up when the
alarm is turned on.
•The clock display will turn on when the clock is connected to power.
•If the clock is disconnected from power, it will only save the me
and sengs for 60 seconds.
Display Modes
•Press the [UP] buon on the back of the clock to switch between
clock display modes. Press the [SET] buon to save as the default
mode.
•Mode 1 shows the me for 10 seconds and the date and
temperature for 2 seconds.
•Mode 2 shows the me, alarm, date and temperature at all mes.
Seng the Time
•Press the [SET] buon unl the me is displayed.
•Press and hold the [SET] buon to set the me. The me hours will
begin flashing. Press the [UP] and [DOWN] buons to adjust. The
dot in the upper lecorner of the display will appear when the hour
is PM. Press the [SET] buon to save the hour seng.
•The minute digits will begin flashing. Press the [UP] and [DOWN]
buons to adjust, and press the [SET] buon to save. The clock will
return to its default display mode.
Changing Temperature Units
•Press the [SET] buon unl the temperature is displayed.
•Press the [DOWN] buon to switch between degrees Fahrenheit (⁰F)
and Celsius (⁰C).
•Press the [SET] buon to save. The clock will return to default
display mode.
•When the alarm is turned on, press and hold the [SET] buon to set
the alarm me. The alarm hours will begin flashing. Press the [UP]
and [DOWN] buons to adjust. Press the [SET] buon to save alarm
hour seng.
•The alarm minute digits will begin flashing. Press the [UP] and
[DOWN] buons to adjust, and press the [SET] buon to save. The
clock will return to its default display mode.
Seng the Date
•Press the [SET] buon unl the date is displayed.
•Press and hold the [SET] buon to set the date. The year will begin
flashing. Press the [UP] and [DOWN] buons to adjust. Press the
[SET] buon to save year seng.
•The month will begin flashing. Press the [UP] and [DOWN] buons
to adjust, and press the [SET] buon to save month seng.
•The day will begin flashing. Press the [UP] and [DOWN] buons to
adjust, and press the [SET] buon to save. The clock will return to
default display mode.
Using the Bedside Light
•Press the [SNOOZE/LIGHT] buon on the top of the clock to turn
the bedside light ON in white light mode.
•Press the [SNOOZE/LIGHT] buon to adjust the light brightness
between low, medium and high.
•Press and hold the [SNOOZE/LIGHT] buon to switch to color-
changing light mode.
•In color-changing light mode, press the [SNOOZE/LIGHT] buon to
choose a light color.
•Press and hold the [SNOOZE/LIGHT] buon to switch back to white
light mode.
Snooze Funcon
•Press the [SNOOZE/LIGHT] buon on the top of the clock when the
alarm goes offto acvated the Snooze funcon. The alarm will ring
again in 5 minutes. The sunrise light will connue to shine at full
brightness during the snooze me.
•To turn the alarm and sunrise light offcompletely, press and hold
the [SNOOZE/LIGHT] buon when alarm goes off. This only turns
them offfor the day, and they will acvate again as normal the next
day.
Using the Sunrise Light
•The clock’s sunrise light funcon will turn on 20 minutes before
your alarm me, and gradually increase in brightness unl your
alarm goes off.
•To use the sunrise light, set the alarm before your go to sleep.
Wireless Charging & USB Output
Note:
•The bedside light can only be powered OFF from white light mode.
•The bedside light can NOT be used when the clock is in sunrise mode
or snooze mode.
•The LED indicator will flash RED and BLUE alternavely, then turn
RED to indicate the charging pad is in standby mode and ready to
begin charge, when the clock is connected to power.
•Place a wireless charging enabled device on the charging pad, the
wireless charger will begin to charge automacally. The LED
indicator will glow BLUE to indicate your device is charging properly.
If your device does not begin to charge, try reposioning your
device on the charging pad. You may need to remove your
smartphone case to charge properly.
•When your device is fully charged, the wireless charging LED
indicator will turn RED. Remove your device from the charging pad.
•Note: If the LED indicator is flashing RED and Blue when the charging
pad is in use, either the device is NOT wireless charging enabled, or
there is an object between the device and charging pad interfering with
the charging process.
• To power or to charge a USB device using the USB power output
port on the back of the clock, simply plug your device’s USB
connector into the USB output port and the other end into your
device.
Tech Specificaons
• USB-C Input: DC 5V/2A
• Wireless Charging Output: 5W (Max)
• USB-A Output: DC 5V/1A
FCC Informaon
TThis device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Made in China
Product
Connecng to Power
•Plug the small connector of the included charging cable into the
USB-C charging port on the clock.
•Plug the large connector into a USB power source, such as a
compable 5V/2A USB power adapter (not included) and plug into
a wall outlet.
Wireless Charging Surface
83MM
front
back
83MM 83MM 83MM
83MM 83MM 83MM 83MM
120MM120MM
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the
device must be respected.

Sunrise Alarm Clock with Himalayan Salt Lamp
& Wireless Charger
Instrucon Manual
XO-9917
•XO-9917 Sunrise Alarm Clock with WirelessCharger (x1)
•Power Cable (x1)
•User Manual (x1)
•This product is NOT a toy, keep away from children and pets.
•Only use the device according to the instrucons in this manual. Never
use the device for anything other than its intended purpose.
•This device is NOT a substute for proper medical equipment or
aenon.
•ONLY use the supplied power cable.
•Do not open this product or aempt to repair the unit yourself if it is
not working properly. Doing so risks fire, shock or injury.
•When not in use, the device should be stored in a dry, cool locaon,
away from sources of water or heat.
•Do not expose device or power cable to extreme temperatures (heat or
cold), open flames, humid or wet condions.
•Do not submerge in water. Do not use in a locaon where the device or
power cable could fall into liquid.
•Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
•Do not use if device or power cable is damaged. If device or power
cable is damaged, it MUST be serviced or replaced by the manufacturer
or its service agent before using again.
•Aachments on the back of your device can impede effecveness of
the wireless charger, and lead to overheang. Remove aachments
from your device before charging on this wireless charger.
Safety Precauons
In the Box
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS
MANUAL
Seng the Alarm
•Press the [SET] buon unl the alarm me is displayed.
•Press the [DOWN] buon to turn the alarm ON or OFF. The dot in
the lower lecorner of the clock display will light up when the
alarm is turned on.
•The clock display will turn on when the clock is connected to power.
•If the clock is disconnected from power, it will only save the me
and sengs for 60 seconds.
Display Modes
•Press the [UP] buon on the back of the clock to switch between
clock display modes. Press the [SET] buon to save as the default
mode.
•Mode 1 shows the me for 10 seconds and the date and
temperature for 2 seconds.
•Mode 2 shows the me, alarm, date and temperature at all mes.
Seng the Time
•Press the [SET] buon unl the me is displayed.
•Press and hold the [SET] buon to set the me. The me hours will
begin flashing. Press the [UP] and [DOWN] buons to adjust. The
dot in the upper lecorner of the display will appear when the hour
is PM. Press the [SET] buon to save the hour seng.
•The minute digits will begin flashing. Press the [UP] and [DOWN]
buons to adjust, and press the [SET] buon to save. The clock will
return to its default display mode.
Changing Temperature Units
•Press the [SET] buon unl the temperature is displayed.
•Press the [DOWN] buon to switch between degrees Fahrenheit (⁰F)
and Celsius (⁰C).
•Press the [SET] buon to save. The clock will return to default
display mode.
•When the alarm is turned on, press and hold the [SET] buon to set
the alarm me. The alarm hours will begin flashing. Press the [UP]
and [DOWN] buons to adjust. Press the [SET] buon to save alarm
hour seng.
•The alarm minute digits will begin flashing. Press the [UP] and
[DOWN] buons to adjust, and press the [SET] buon to save. The
clock will return to its default display mode.
Seng the Date
•Press the [SET] buon unl the date is displayed.
•Press and hold the [SET] buon to set the date. The year will begin
flashing. Press the [UP] and [DOWN] buons to adjust. Press the
[SET] buon to save year seng.
•The month will begin flashing. Press the [UP] and [DOWN] buons
to adjust, and press the [SET] buon to save month seng.
•The day will begin flashing. Press the [UP] and [DOWN] buons to
adjust, and press the [SET] buon to save. The clock will return to
default display mode.
Using the Bedside Light
•Press the [SNOOZE/LIGHT] buon on the top of the clock to turn
the bedside light ON in white light mode.
•Press the [SNOOZE/LIGHT] buon to adjust the light brightness
between low, medium and high.
•Press and hold the [SNOOZE/LIGHT] buon to switch to color-
changing light mode.
•In color-changing light mode, press the [SNOOZE/LIGHT] buon to
choose a light color.
•Press and hold the [SNOOZE/LIGHT] buon to switch back to white
light mode.
Snooze Funcon
•Press the [SNOOZE/LIGHT] buon on the top of the clock when the
alarm goes offto acvated the Snooze funcon. The alarm will ring
again in 5 minutes. The sunrise light will connue to shine at full
brightness during the snooze me.
•To turn the alarm and sunrise light offcompletely, press and hold
the [SNOOZE/LIGHT] buon when alarm goes off. This only turns
them offfor the day, and they will acvate again as normal the next
day.
Using the Sunrise Light
•The clock’s sunrise light funcon will turn on 20 minutes before
your alarm me, and gradually increase in brightness unl your
alarm goes off.
•To use the sunrise light, set the alarm before your go to sleep.
Wireless Charging & USB Output
Note:
•The bedside light can only be powered OFF from white light mode.
•The bedside light can NOT be used when the clock is in sunrise mode
or snooze mode.
•The LED indicator will flash RED and BLUE alternavely, then turn
RED to indicate the charging pad is in standby mode and ready to
begin charge, when the clock is connected to power.
•Place a wireless charging enabled device on the charging pad, the
wireless charger will begin to charge automacally. The LED
indicator will glow BLUE to indicate your device is charging properly.
If your device does not begin to charge, try reposioning your
device on the charging pad. You may need to remove your
smartphone case to charge properly.
•When your device is fully charged, the wireless charging LED
indicator will turn RED. Remove your device from the charging pad.
•Note: If the LED indicator is flashing RED and Blue when the charging
pad is in use, either the device is NOT wireless charging enabled, or
there is an object between the device and charging pad interfering with
the charging process.
• To power or to charge a USB device using the USB power output
port on the back of the clock, simply plug your device’s USB
connector into the USB output port and the other end into your
device.
Tech Specificaons
• USB-C Input: DC 5V/2A
• Wireless Charging Output: 5W (Max)
• USB-A Output: DC 5V/1A
FCC Informaon
TThis device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Made in China
Product
Connecng to Power
•Plug the small connector of the included charging cable into the
USB-C charging port on the clock.
•Plug the large connector into a USB power source, such as a
compable 5V/2A USB power adapter (not included) and plug into
a wall outlet.
Wireless Charging Surface
83MM
front
back
83MM 83MM 83MM
83MM 83MM 83MM 83MM
120MM120MM
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the
device must be respected.

Sunrise Alarm Clock with Himalayan Salt Lamp
& Wireless Charger
Instrucon Manual
XO-9917
•XO-9917 Sunrise Alarm Clock with WirelessCharger (x1)
•Power Cable (x1)
•User Manual (x1)
•This product is NOT a toy, keep away from children and pets.
•Only use the device according to the instrucons in this manual. Never
use the device for anything other than its intended purpose.
•This device is NOT a substute for proper medical equipment or
aenon.
•ONLY use the supplied power cable.
•Do not open this product or aempt to repair the unit yourself if it is
not working properly. Doing so risks fire, shock or injury.
•When not in use, the device should be stored in a dry, cool locaon,
away from sources of water or heat.
•Do not expose device or power cable to extreme temperatures (heat or
cold), open flames, humid or wet condions.
•Do not submerge in water. Do not use in a locaon where the device or
power cable could fall into liquid.
•Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
•Do not use if device or power cable is damaged. If device or power
cable is damaged, it MUST be serviced or replaced by the manufacturer
or its service agent before using again.
•Aachments on the back of your device can impede effecveness of
the wireless charger, and lead to overheang. Remove aachments
from your device before charging on this wireless charger.
Safety Precauons
In the Box
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS
MANUAL
Seng the Alarm
•Press the [SET] buon unl the alarm me is displayed.
•Press the [DOWN] buon to turn the alarm ON or OFF. The dot in
the lower lecorner of the clock display will light up when the
alarm is turned on.
•The clock display will turn on when the clock is connected to power.
•If the clock is disconnected from power, it will only save the me
and sengs for 60 seconds.
Display Modes
•Press the [UP] buon on the back of the clock to switch between
clock display modes. Press the [SET] buon to save as the default
mode.
•Mode 1 shows the me for 10 seconds and the date and
temperature for 2 seconds.
•Mode 2 shows the me, alarm, date and temperature at all mes.
Seng the Time
•Press the [SET] buon unl the me is displayed.
•Press and hold the [SET] buon to set the me. The me hours will
begin flashing. Press the [UP] and [DOWN] buons to adjust. The
dot in the upper lecorner of the display will appear when the hour
is PM. Press the [SET] buon to save the hour seng.
•The minute digits will begin flashing. Press the [UP] and [DOWN]
buons to adjust, and press the [SET] buon to save. The clock will
return to its default display mode.
Changing Temperature Units
•Press the [SET] buon unl the temperature is displayed.
•Press the [DOWN] buon to switch between degrees Fahrenheit (⁰F)
and Celsius (⁰C).
•Press the [SET] buon to save. The clock will return to default
display mode.
•When the alarm is turned on, press and hold the [SET] buon to set
the alarm me. The alarm hours will begin flashing. Press the [UP]
and [DOWN] buons to adjust. Press the [SET] buon to save alarm
hour seng.
•The alarm minute digits will begin flashing. Press the [UP] and
[DOWN] buons to adjust, and press the [SET] buon to save. The
clock will return to its default display mode.
Seng the Date
•Press the [SET] buon unl the date is displayed.
•Press and hold the [SET] buon to set the date. The year will begin
flashing. Press the [UP] and [DOWN] buons to adjust. Press the
[SET] buon to save year seng.
•The month will begin flashing. Press the [UP] and [DOWN] buons
to adjust, and press the [SET] buon to save month seng.
•The day will begin flashing. Press the [UP] and [DOWN] buons to
adjust, and press the [SET] buon to save. The clock will return to
default display mode.
Using the Bedside Light
•Press the [SNOOZE/LIGHT] buon on the top of the clock to turn
the bedside light ON in white light mode.
•Press the [SNOOZE/LIGHT] buon to adjust the light brightness
between low, medium and high.
•Press and hold the [SNOOZE/LIGHT] buon to switch to color-
changing light mode.
•In color-changing light mode, press the [SNOOZE/LIGHT] buon to
choose a light color.
•Press and hold the [SNOOZE/LIGHT] buon to switch back to white
light mode.
Snooze Funcon
•Press the [SNOOZE/LIGHT] buon on the top of the clock when the
alarm goes offto acvated the Snooze funcon. The alarm will ring
again in 5 minutes. The sunrise light will connue to shine at full
brightness during the snooze me.
•To turn the alarm and sunrise light offcompletely, press and hold
the [SNOOZE/LIGHT] buon when alarm goes off. This only turns
them offfor the day, and they will acvate again as normal the next
day.
Using the Sunrise Light
•The clock’s sunrise light funcon will turn on 20 minutes before
your alarm me, and gradually increase in brightness unl your
alarm goes off.
•To use the sunrise light, set the alarm before your go to sleep.
Wireless Charging & USB Output
Note:
•The bedside light can only be powered OFF from white light mode.
•The bedside light can NOT be used when the clock is in sunrise mode
or snooze mode.
•The LED indicator will flash RED and BLUE alternavely, then turn
RED to indicate the charging pad is in standby mode and ready to
begin charge, when the clock is connected to power.
•Place a wireless charging enabled device on the charging pad, the
wireless charger will begin to charge automacally. The LED
indicator will glow BLUE to indicate your device is charging properly.
If your device does not begin to charge, try reposioning your
device on the charging pad. You may need to remove your
smartphone case to charge properly.
•When your device is fully charged, the wireless charging LED
indicator will turn RED. Remove your device from the charging pad.
•Note: If the LED indicator is flashing RED and Blue when the charging
pad is in use, either the device is NOT wireless charging enabled, or
there is an object between the device and charging pad interfering with
the charging process.
• To power or to charge a USB device using the USB power output
port on the back of the clock, simply plug your device’s USB
connector into the USB output port and the other end into your
device.
Tech Specificaons
• USB-C Input: DC 5V/2A
• Wireless Charging Output: 5W (Max)
• USB-A Output: DC 5V/1A
FCC Informaon
TThis device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Made in China
Product
Connecng to Power
•Plug the small connector of the included charging cable into the
USB-C charging port on the clock.
•Plug the large connector into a USB power source, such as a
compable 5V/2A USB power adapter (not included) and plug into
a wall outlet.
Wireless Charging Surface
83MM
front
back
83MM 83MM 83MM
83MM 83MM 83MM 83MM
120MM120MM
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the
device must be respected.

Sunrise Alarm Clock with Himalayan Salt Lamp
& Wireless Charger
Instrucon Manual
XO-9917
•XO-9917 Sunrise Alarm Clock with WirelessCharger (x1)
•Power Cable (x1)
•User Manual (x1)
•This product is NOT a toy, keep away from children and pets.
•Only use the device according to the instrucons in this manual. Never
use the device for anything other than its intended purpose.
•This device is NOT a substute for proper medical equipment or
aenon.
•ONLY use the supplied power cable.
•Do not open this product or aempt to repair the unit yourself if it is
not working properly. Doing so risks fire, shock or injury.
•When not in use, the device should be stored in a dry, cool locaon,
away from sources of water or heat.
•Do not expose device or power cable to extreme temperatures (heat or
cold), open flames, humid or wet condions.
•Do not submerge in water. Do not use in a locaon where the device or
power cable could fall into liquid.
•Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
•Do not use if device or power cable is damaged. If device or power
cable is damaged, it MUST be serviced or replaced by the manufacturer
or its service agent before using again.
•Aachments on the back of your device can impede effecveness of
the wireless charger, and lead to overheang. Remove aachments
from your device before charging on this wireless charger.
Safety Precauons
In the Box
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS
MANUAL
Seng the Alarm
•Press the [SET] buon unl the alarm me is displayed.
•Press the [DOWN] buon to turn the alarm ON or OFF. The dot in
the lower lecorner of the clock display will light up when the
alarm is turned on.
•The clock display will turn on when the clock is connected to power.
•If the clock is disconnected from power, it will only save the me
and sengs for 60 seconds.
Display Modes
•Press the [UP] buon on the back of the clock to switch between
clock display modes. Press the [SET] buon to save as the default
mode.
•Mode 1 shows the me for 10 seconds and the date and
temperature for 2 seconds.
•Mode 2 shows the me, alarm, date and temperature at all mes.
Seng the Time
•Press the [SET] buon unl the me is displayed.
•Press and hold the [SET] buon to set the me. The me hours will
begin flashing. Press the [UP] and [DOWN] buons to adjust. The
dot in the upper lecorner of the display will appear when the hour
is PM. Press the [SET] buon to save the hour seng.
•The minute digits will begin flashing. Press the [UP] and [DOWN]
buons to adjust, and press the [SET] buon to save. The clock will
return to its default display mode.
Changing Temperature Units
•Press the [SET] buon unl the temperature is displayed.
•Press the [DOWN] buon to switch between degrees Fahrenheit (⁰F)
and Celsius (⁰C).
•Press the [SET] buon to save. The clock will return to default
display mode.
•When the alarm is turned on, press and hold the [SET] buon to set
the alarm me. The alarm hours will begin flashing. Press the [UP]
and [DOWN] buons to adjust. Press the [SET] buon to save alarm
hour seng.
•The alarm minute digits will begin flashing. Press the [UP] and
[DOWN] buons to adjust, and press the [SET] buon to save. The
clock will return to its default display mode.
Seng the Date
•Press the [SET] buon unl the date is displayed.
•Press and hold the [SET] buon to set the date. The year will begin
flashing. Press the [UP] and [DOWN] buons to adjust. Press the
[SET] buon to save year seng.
•The month will begin flashing. Press the [UP] and [DOWN] buons
to adjust, and press the [SET] buon to save month seng.
•The day will begin flashing. Press the [UP] and [DOWN] buons to
adjust, and press the [SET] buon to save. The clock will return to
default display mode.
Using the Bedside Light
•Press the [SNOOZE/LIGHT] buon on the top of the clock to turn
the bedside light ON in white light mode.
•Press the [SNOOZE/LIGHT] buon to adjust the light brightness
between low, medium and high.
•Press and hold the [SNOOZE/LIGHT] buon to switch to color-
changing light mode.
•In color-changing light mode, press the [SNOOZE/LIGHT] buon to
choose a light color.
•Press and hold the [SNOOZE/LIGHT] buon to switch back to white
light mode.
Snooze Funcon
•Press the [SNOOZE/LIGHT] buon on the top of the clock when the
alarm goes offto acvated the Snooze funcon. The alarm will ring
again in 5 minutes. The sunrise light will connue to shine at full
brightness during the snooze me.
•To turn the alarm and sunrise light offcompletely, press and hold
the [SNOOZE/LIGHT] buon when alarm goes off. This only turns
them offfor the day, and they will acvate again as normal the next
day.
Using the Sunrise Light
•The clock’s sunrise light funcon will turn on 20 minutes before
your alarm me, and gradually increase in brightness unl your
alarm goes off.
•To use the sunrise light, set the alarm before your go to sleep.
Wireless Charging & USB Output
Note:
•The bedside light can only be powered OFF from white light mode.
•The bedside light can NOT be used when the clock is in sunrise mode
or snooze mode.
•The LED indicator will flash RED and BLUE alternavely, then turn
RED to indicate the charging pad is in standby mode and ready to
begin charge, when the clock is connected to power.
•Place a wireless charging enabled device on the charging pad, the
wireless charger will begin to charge automacally. The LED
indicator will glow BLUE to indicate your device is charging properly.
If your device does not begin to charge, try reposioning your
device on the charging pad. You may need to remove your
smartphone case to charge properly.
•When your device is fully charged, the wireless charging LED
indicator will turn RED. Remove your device from the charging pad.
•Note: If the LED indicator is flashing RED and Blue when the charging
pad is in use, either the device is NOT wireless charging enabled, or
there is an object between the device and charging pad interfering with
the charging process.
• To power or to charge a USB device using the USB power output
port on the back of the clock, simply plug your device’s USB
connector into the USB output port and the other end into your
device.
Tech Specificaons
• USB-C Input: DC 5V/2A
• Wireless Charging Output: 5W (Max)
• USB-A Output: DC 5V/1A
FCC Informaon
TThis device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Made in China
Product
Connecng to Power
•Plug the small connector of the included charging cable into the
USB-C charging port on the clock.
•Plug the large connector into a USB power source, such as a
compable 5V/2A USB power adapter (not included) and plug into
a wall outlet.
Wireless Charging Surface
83MM
front
back
83MM 83MM 83MM
83MM 83MM 83MM 83MM
120MM120MM
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the
device must be respected.

Sunrise Alarm Clock with Himalayan Salt Lamp
& Wireless Charger
Instrucon Manual
XO-9917
•XO-9917 Sunrise Alarm Clock with WirelessCharger (x1)
•Power Cable (x1)
•User Manual (x1)
•This product is NOT a toy, keep away from children and pets.
•Only use the device according to the instrucons in this manual. Never
use the device for anything other than its intended purpose.
•This device is NOT a substute for proper medical equipment or
aenon.
•ONLY use the supplied power cable.
•Do not open this product or aempt to repair the unit yourself if it is
not working properly. Doing so risks fire, shock or injury.
•When not in use, the device should be stored in a dry, cool locaon,
away from sources of water or heat.
•Do not expose device or power cable to extreme temperatures (heat or
cold), open flames, humid or wet condions.
•Do not submerge in water. Do not use in a locaon where the device or
power cable could fall into liquid.
•Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
•Do not use if device or power cable is damaged. If device or power
cable is damaged, it MUST be serviced or replaced by the manufacturer
or its service agent before using again.
•Aachments on the back of your device can impede effecveness of
the wireless charger, and lead to overheang. Remove aachments
from your device before charging on this wireless charger.
Safety Precauons
In the Box
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS
MANUAL
Seng the Alarm
•Press the [SET] buon unl the alarm me is displayed.
•Press the [DOWN] buon to turn the alarm ON or OFF. The dot in
the lower lecorner of the clock display will light up when the
alarm is turned on.
•The clock display will turn on when the clock is connected to power.
•If the clock is disconnected from power, it will only save the me
and sengs for 60 seconds.
Display Modes
•Press the [UP] buon on the back of the clock to switch between
clock display modes. Press the [SET] buon to save as the default
mode.
•Mode 1 shows the me for 10 seconds and the date and
temperature for 2 seconds.
•Mode 2 shows the me, alarm, date and temperature at all mes.
Seng the Time
•Press the [SET] buon unl the me is displayed.
•Press and hold the [SET] buon to set the me. The me hours will
begin flashing. Press the [UP] and [DOWN] buons to adjust. The
dot in the upper lecorner of the display will appear when the hour
is PM. Press the [SET] buon to save the hour seng.
•The minute digits will begin flashing. Press the [UP] and [DOWN]
buons to adjust, and press the [SET] buon to save. The clock will
return to its default display mode.
Changing Temperature Units
•Press the [SET] buon unl the temperature is displayed.
•Press the [DOWN] buon to switch between degrees Fahrenheit (⁰F)
and Celsius (⁰C).
•Press the [SET] buon to save. The clock will return to default
display mode.
•When the alarm is turned on, press and hold the [SET] buon to set
the alarm me. The alarm hours will begin flashing. Press the [UP]
and [DOWN] buons to adjust. Press the [SET] buon to save alarm
hour seng.
•The alarm minute digits will begin flashing. Press the [UP] and
[DOWN] buons to adjust, and press the [SET] buon to save. The
clock will return to its default display mode.
Seng the Date
•Press the [SET] buon unl the date is displayed.
•Press and hold the [SET] buon to set the date. The year will begin
flashing. Press the [UP] and [DOWN] buons to adjust. Press the
[SET] buon to save year seng.
•The month will begin flashing. Press the [UP] and [DOWN] buons
to adjust, and press the [SET] buon to save month seng.
•The day will begin flashing. Press the [UP] and [DOWN] buons to
adjust, and press the [SET] buon to save. The clock will return to
default display mode.
Using the Bedside Light
•Press the [SNOOZE/LIGHT] buon on the top of the clock to turn
the bedside light ON in white light mode.
•Press the [SNOOZE/LIGHT] buon to adjust the light brightness
between low, medium and high.
•Press and hold the [SNOOZE/LIGHT] buon to switch to color-
changing light mode.
•In color-changing light mode, press the [SNOOZE/LIGHT] buon to
choose a light color.
•Press and hold the [SNOOZE/LIGHT] buon to switch back to white
light mode.
Snooze Funcon
•Press the [SNOOZE/LIGHT] buon on the top of the clock when the
alarm goes offto acvated the Snooze funcon. The alarm will ring
again in 5 minutes. The sunrise light will connue to shine at full
brightness during the snooze me.
•To turn the alarm and sunrise light offcompletely, press and hold
the [SNOOZE/LIGHT] buon when alarm goes off. This only turns
them offfor the day, and they will acvate again as normal the next
day.
Using the Sunrise Light
•The clock’s sunrise light funcon will turn on 20 minutes before
your alarm me, and gradually increase in brightness unl your
alarm goes off.
•To use the sunrise light, set the alarm before your go to sleep.
Wireless Charging & USB Output
Note:
•The bedside light can only be powered OFF from white light mode.
•The bedside light can NOT be used when the clock is in sunrise mode
or snooze mode.
•The LED indicator will flash RED and BLUE alternavely, then turn
RED to indicate the charging pad is in standby mode and ready to
begin charge, when the clock is connected to power.
•Place a wireless charging enabled device on the charging pad, the
wireless charger will begin to charge automacally. The LED
indicator will glow BLUE to indicate your device is charging properly.
If your device does not begin to charge, try reposioning your
device on the charging pad. You may need to remove your
smartphone case to charge properly.
•When your device is fully charged, the wireless charging LED
indicator will turn RED. Remove your device from the charging pad.
•Note: If the LED indicator is flashing RED and Blue when the charging
pad is in use, either the device is NOT wireless charging enabled, or
there is an object between the device and charging pad interfering with
the charging process.
• To power or to charge a USB device using the USB power output
port on the back of the clock, simply plug your device’s USB
connector into the USB output port and the other end into your
device.
Tech Specificaons
• USB-C Input: DC 5V/2A
• Wireless Charging Output: 5W (Max)
• USB-A Output: DC 5V/1A
FCC Informaon
TThis device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Made in China
Product
Connecng to Power
•Plug the small connector of the included charging cable into the
USB-C charging port on the clock.
•Plug the large connector into a USB power source, such as a
compable 5V/2A USB power adapter (not included) and plug into
a wall outlet.
Wireless Charging Surface
83MM
front
back
83MM 83MM 83MM
83MM 83MM 83MM 83MM
120MM120MM
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the
device must be respected.

Sunrise Alarm Clock with Himalayan Salt Lamp
& Wireless Charger
Instrucon Manual
XO-9917
•XO-9917 Sunrise Alarm Clock with WirelessCharger (x1)
•Power Cable (x1)
•User Manual (x1)
•This product is NOT a toy, keep away from children and pets.
•Only use the device according to the instrucons in this manual. Never
use the device for anything other than its intended purpose.
•This device is NOT a substute for proper medical equipment or
aenon.
•ONLY use the supplied power cable.
•Do not open this product or aempt to repair the unit yourself if it is
not working properly. Doing so risks fire, shock or injury.
•When not in use, the device should be stored in a dry, cool locaon,
away from sources of water or heat.
•Do not expose device or power cable to extreme temperatures (heat or
cold), open flames, humid or wet condions.
•Do not submerge in water. Do not use in a locaon where the device or
power cable could fall into liquid.
•Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
•Do not use if device or power cable is damaged. If device or power
cable is damaged, it MUST be serviced or replaced by the manufacturer
or its service agent before using again.
•Aachments on the back of your device can impede effecveness of
the wireless charger, and lead to overheang. Remove aachments
from your device before charging on this wireless charger.
Safety Precauons
In the Box
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS
MANUAL
Seng the Alarm
•Press the [SET] buon unl the alarm me is displayed.
•Press the [DOWN] buon to turn the alarm ON or OFF. The dot in
the lower lecorner of the clock display will light up when the
alarm is turned on.
•The clock display will turn on when the clock is connected to power.
•If the clock is disconnected from power, it will only save the me
and sengs for 60 seconds.
Display Modes
•Press the [UP] buon on the back of the clock to switch between
clock display modes. Press the [SET] buon to save as the default
mode.
•Mode 1 shows the me for 10 seconds and the date and
temperature for 2 seconds.
•Mode 2 shows the me, alarm, date and temperature at all mes.
Seng the Time
•Press the [SET] buon unl the me is displayed.
•Press and hold the [SET] buon to set the me. The me hours will
begin flashing. Press the [UP] and [DOWN] buons to adjust. The
dot in the upper lecorner of the display will appear when the hour
is PM. Press the [SET] buon to save the hour seng.
•The minute digits will begin flashing. Press the [UP] and [DOWN]
buons to adjust, and press the [SET] buon to save. The clock will
return to its default display mode.
Changing Temperature Units
•Press the [SET] buon unl the temperature is displayed.
•Press the [DOWN] buon to switch between degrees Fahrenheit (⁰F)
and Celsius (⁰C).
•Press the [SET] buon to save. The clock will return to default
display mode.
•When the alarm is turned on, press and hold the [SET] buon to set
the alarm me. The alarm hours will begin flashing. Press the [UP]
and [DOWN] buons to adjust. Press the [SET] buon to save alarm
hour seng.
•The alarm minute digits will begin flashing. Press the [UP] and
[DOWN] buons to adjust, and press the [SET] buon to save. The
clock will return to its default display mode.
Seng the Date
•Press the [SET] buon unl the date is displayed.
•Press and hold the [SET] buon to set the date. The year will begin
flashing. Press the [UP] and [DOWN] buons to adjust. Press the
[SET] buon to save year seng.
•The month will begin flashing. Press the [UP] and [DOWN] buons
to adjust, and press the [SET] buon to save month seng.
•The day will begin flashing. Press the [UP] and [DOWN] buons to
adjust, and press the [SET] buon to save. The clock will return to
default display mode.
Using the Bedside Light
•Press the [SNOOZE/LIGHT] buon on the top of the clock to turn
the bedside light ON in white light mode.
•Press the [SNOOZE/LIGHT] buon to adjust the light brightness
between low, medium and high.
•Press and hold the [SNOOZE/LIGHT] buon to switch to color-
changing light mode.
•In color-changing light mode, press the [SNOOZE/LIGHT] buon to
choose a light color.
•Press and hold the [SNOOZE/LIGHT] buon to switch back to white
light mode.
Snooze Funcon
•Press the [SNOOZE/LIGHT] buon on the top of the clock when the
alarm goes offto acvated the Snooze funcon. The alarm will ring
again in 5 minutes. The sunrise light will connue to shine at full
brightness during the snooze me.
•To turn the alarm and sunrise light offcompletely, press and hold
the [SNOOZE/LIGHT] buon when alarm goes off. This only turns
them offfor the day, and they will acvate again as normal the next
day.
Using the Sunrise Light
•The clock’s sunrise light funcon will turn on 20 minutes before
your alarm me, and gradually increase in brightness unl your
alarm goes off.
•To use the sunrise light, set the alarm before your go to sleep.
Wireless Charging & USB Output
Note:
•The bedside light can only be powered OFF from white light mode.
•The bedside light can NOT be used when the clock is in sunrise mode
or snooze mode.
•The LED indicator will flash RED and BLUE alternavely, then turn
RED to indicate the charging pad is in standby mode and ready to
begin charge, when the clock is connected to power.
•Place a wireless charging enabled device on the charging pad, the
wireless charger will begin to charge automacally. The LED
indicator will glow BLUE to indicate your device is charging properly.
If your device does not begin to charge, try reposioning your
device on the charging pad. You may need to remove your
smartphone case to charge properly.
•When your device is fully charged, the wireless charging LED
indicator will turn RED. Remove your device from the charging pad.
•Note: If the LED indicator is flashing RED and Blue when the charging
pad is in use, either the device is NOT wireless charging enabled, or
there is an object between the device and charging pad interfering with
the charging process.
• To power or to charge a USB device using the USB power output
port on the back of the clock, simply plug your device’s USB
connector into the USB output port and the other end into your
device.
Tech Specificaons
• USB-C Input: DC 5V/2A
• Wireless Charging Output: 5W (Max)
• USB-A Output: DC 5V/1A
FCC Informaon
TThis device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Made in China
Product
Connecng to Power
•Plug the small connector of the included charging cable into the
USB-C charging port on the clock.
•Plug the large connector into a USB power source, such as a
compable 5V/2A USB power adapter (not included) and plug into
a wall outlet.
Wireless Charging Surface
83MM
front
back
83MM 83MM 83MM
83MM 83MM 83MM 83MM
120MM120MM
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the
device must be respected.

Sunrise Alarm Clock with Himalayan Salt Lamp
& Wireless Charger
Instrucon Manual
XO-9917
•XO-9917 Sunrise Alarm Clock with WirelessCharger (x1)
•Power Cable (x1)
•User Manual (x1)
•This product is NOT a toy, keep away from children and pets.
•Only use the device according to the instrucons in this manual. Never
use the device for anything other than its intended purpose.
•This device is NOT a substute for proper medical equipment or
aenon.
•ONLY use the supplied power cable.
•Do not open this product or aempt to repair the unit yourself if it is
not working properly. Doing so risks fire, shock or injury.
•When not in use, the device should be stored in a dry, cool locaon,
away from sources of water or heat.
•Do not expose device or power cable to extreme temperatures (heat or
cold), open flames, humid or wet condions.
•Do not submerge in water. Do not use in a locaon where the device or
power cable could fall into liquid.
•Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
•Do not use if device or power cable is damaged. If device or power
cable is damaged, it MUST be serviced or replaced by the manufacturer
or its service agent before using again.
•Aachments on the back of your device can impede effecveness of
the wireless charger, and lead to overheang. Remove aachments
from your device before charging on this wireless charger.
Safety Precauons
In the Box
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS
MANUAL
Seng the Alarm
•Press the [SET] buon unl the alarm me is displayed.
•Press the [DOWN] buon to turn the alarm ON or OFF. The dot in
the lower lecorner of the clock display will light up when the
alarm is turned on.
•The clock display will turn on when the clock is connected to power.
•If the clock is disconnected from power, it will only save the me
and sengs for 60 seconds.
Display Modes
•Press the [UP] buon on the back of the clock to switch between
clock display modes. Press the [SET] buon to save as the default
mode.
•Mode 1 shows the me for 10 seconds and the date and
temperature for 2 seconds.
•Mode 2 shows the me, alarm, date and temperature at all mes.
Seng the Time
•Press the [SET] buon unl the me is displayed.
•Press and hold the [SET] buon to set the me. The me hours will
begin flashing. Press the [UP] and [DOWN] buons to adjust. The
dot in the upper lecorner of the display will appear when the hour
is PM. Press the [SET] buon to save the hour seng.
•The minute digits will begin flashing. Press the [UP] and [DOWN]
buons to adjust, and press the [SET] buon to save. The clock will
return to its default display mode.
Changing Temperature Units
•Press the [SET] buon unl the temperature is displayed.
•Press the [DOWN] buon to switch between degrees Fahrenheit (⁰F)
and Celsius (⁰C).
•Press the [SET] buon to save. The clock will return to default
display mode.
•When the alarm is turned on, press and hold the [SET] buon to set
the alarm me. The alarm hours will begin flashing. Press the [UP]
and [DOWN] buons to adjust. Press the [SET] buon to save alarm
hour seng.
•The alarm minute digits will begin flashing. Press the [UP] and
[DOWN] buons to adjust, and press the [SET] buon to save. The
clock will return to its default display mode.
Seng the Date
•Press the [SET] buon unl the date is displayed.
•Press and hold the [SET] buon to set the date. The year will begin
flashing. Press the [UP] and [DOWN] buons to adjust. Press the
[SET] buon to save year seng.
•The month will begin flashing. Press the [UP] and [DOWN] buons
to adjust, and press the [SET] buon to save month seng.
•The day will begin flashing. Press the [UP] and [DOWN] buons to
adjust, and press the [SET] buon to save. The clock will return to
default display mode.
Using the Bedside Light
•Press the [SNOOZE/LIGHT] buon on the top of the clock to turn
the bedside light ON in white light mode.
•Press the [SNOOZE/LIGHT] buon to adjust the light brightness
between low, medium and high.
•Press and hold the [SNOOZE/LIGHT] buon to switch to color-
changing light mode.
•In color-changing light mode, press the [SNOOZE/LIGHT] buon to
choose a light color.
•Press and hold the [SNOOZE/LIGHT] buon to switch back to white
light mode.
Snooze Funcon
•Press the [SNOOZE/LIGHT] buon on the top of the clock when the
alarm goes offto acvated the Snooze funcon. The alarm will ring
again in 5 minutes. The sunrise light will connue to shine at full
brightness during the snooze me.
•To turn the alarm and sunrise light offcompletely, press and hold
the [SNOOZE/LIGHT] buon when alarm goes off. This only turns
them offfor the day, and they will acvate again as normal the next
day.
Using the Sunrise Light
•The clock’s sunrise light funcon will turn on 20 minutes before
your alarm me, and gradually increase in brightness unl your
alarm goes off.
•To use the sunrise light, set the alarm before your go to sleep.
Wireless Charging & USB Output
Note:
•The bedside light can only be powered OFF from white light mode.
•The bedside light can NOT be used when the clock is in sunrise mode
or snooze mode.
•The LED indicator will flash RED and BLUE alternavely, then turn
RED to indicate the charging pad is in standby mode and ready to
begin charge, when the clock is connected to power.
•Place a wireless charging enabled device on the charging pad, the
wireless charger will begin to charge automacally. The LED
indicator will glow BLUE to indicate your device is charging properly.
If your device does not begin to charge, try reposioning your
device on the charging pad. You may need to remove your
smartphone case to charge properly.
•When your device is fully charged, the wireless charging LED
indicator will turn RED. Remove your device from the charging pad.
•Note: If the LED indicator is flashing RED and Blue when the charging
pad is in use, either the device is NOT wireless charging enabled, or
there is an object between the device and charging pad interfering with
the charging process.
• To power or to charge a USB device using the USB power output
port on the back of the clock, simply plug your device’s USB
connector into the USB output port and the other end into your
device.
Tech Specificaons
• USB-C Input: DC 5V/2A
• Wireless Charging Output: 5W (Max)
• USB-A Output: DC 5V/1A
FCC Informaon
TThis device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Made in China
Product
Connecng to Power
•Plug the small connector of the included charging cable into the
USB-C charging port on the clock.
•Plug the large connector into a USB power source, such as a
compable 5V/2A USB power adapter (not included) and plug into
a wall outlet.
Wireless Charging Surface
83MM
front
back
83MM 83MM 83MM
83MM 83MM 83MM 83MM
120MM120MM
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the
device must be respected.