Lone Rider ADV User manual

ADV Tent
User Guide

Contents:
Quick-Start Reference . . . . . . . . . . . . . . . . 2
Detailed Step-by-Step Setup Guide . . . . . . . . . 3
Rain Fly Setup Guide . . . . . . . . . . . . . . . . . 9
Tent Packing Guide . . . . . . . . . . . . . . . . . 13
1

Quick-Start Reference:
Stake out tent,
assemble frame
and attach to
corners of tent.
Attach tent to
frame using
corresponding
fasteners.
Attach rain fly
to tent using
corresponding
fasteners and
stake out doors.
2

Detailed Step-by-Step Setup Guide:
Step 1:
Unpack contents
of bag and spread
out tent on a flat
and suitable
ground surface.
Step 2:
Use supplied
stakes to evenly
tension floor of
tent from each
corner, as shown:
(If ground is wet or
rocky, place tent on top
of included
groundsheet)
3

Step 3:
Remove aluminum
tent frame from
pouch and
assemble.
Step 4:
Insert each end of
the tent frame into
the aluminum
pole-captures
found at each
corner of the tent.
4

Your tent should
now appear as
shown:
Step 5:
Fasten the top
two tent clips to
the tent frame,
just outside of
each upper pole.
5

(Photo of top tent
clip properly
fastened to tent
frame)
Step 6:
Insert each end of
the upper frame
poles into the
aluminum pole
captures located
above each door.
6

(Photo of upper
frame poles
properly fastened
to aluminum pole
captures)
Your tent should
now appear as
shown:
7

Step 7:
Fasten the three
remaining tent
clips on each side
of the tent to the
tent frame as
pictured:
Your ADV Tent is
now properly set
up and suitable
for use in warm
and dry weather.
(Continue to next page for instructions on securing rain fly to tent) 8

Step 8:
Loosely place
rain fly over
tent, oriented
as shown:
Step 9:
Locate aluminum
pole capture found
at each corner of
the tent.
9

Step 10:
Secure each
aluminum pole
capture to its
corresponding
pole-end,
underneath the
aluminum pole
capture previously
secured, as shown:
Step 11:
Unzip both sides
of each door and
locate aluminum
pole capture
found at top of
each door zipper.
10

Step 12:
Secure each
aluminum pole
capture to its
corresponding
pole-end.
Step 13:
Zip up tent doors
and use supplied
stakes to secure
the tent doors
as shown:
11

Your Lone Rider ADV Tent is now ready for use
in virtually any conditions.
(Continue to next page for instructions on packing tent) 12

Step 1:
Detach and
remove rain fly,
set aside. Detach
tent from frame in
the reverse order
that it was
attached. Remove
tent frame, neatly
collapse and store
in designated bag.
Step 2:
Remove stakes
from ground and
store in
designated
pocket, then fold
tent by ⅓,
as shown:
13

Step 3:
Fold tent again
by ⅓, then place
groundsheet bag
and frame/stake
bag on one end
of tent as shown:
(Lengh of frame/stake
bag should be roughly
equal to width of
folded tent)
Step 4:
Roll the folded
tent tightly
around the
frame/stake bag
and groundsheet
bag, so that it
appears as shown:
14

Step 5:
Place rain fly on
ground surface
and fold in half
along it’s
longest axis,
as shown:
Step 6:
Fold rain fly in
half once more
along its
longest axis,
as shown:
15

Step 7:
Fold rain fly in
half a final time
along its
longest axis,
as shown:
Step 8:
Fold rain fly in
half along its
shortest axis
and place
rolled-up tent
on wide end
of rain fly,
as shown:
16

Step 9:
Roll tent
tightly into
rain fly. The
entire tent roll
should now fit
easily back
into provided
dry bag.
Step 10:
Fold roll-top
enclosure of
dry bag 3 time
and clip to
secure.
Your Lone
Rider ADV Tent
is now properly
packed and
ready for
transport.
17