LTS Security POE-SW1602N User manual

16/24-Port 100M Long-Range PoE Switch
Quick Start Guide

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
i
TABLE OF CONTENTS
Chapter 1 Introduction ...............................................................................................................1
1.1 Overview ..................................................................................................................................1
1.2 Packing List ...............................................................................................................................1
1.3 Appearance ..............................................................................................................................2
1.3.1 Front Panel ......................................................................................................................2
1.3.2 Rear Panel .......................................................................................................................4
Chapter 2 Installation .................................................................................................................5
2.1 Preventive and Cautionary Tips ...............................................................................................5
2.2 Working Environment Requirements.......................................................................................5
2.2.1 Temperature and Humidity .............................................................................................5
2.2.2 Static Electricity Protection .............................................................................................5
2.2.3 Lightning Protection........................................................................................................6
2.2.4 Installation Position.........................................................................................................6
2.3 Installation................................................................................................................................6
2.4 Grounding ................................................................................................................................7
2.4.1 With Grounding Bar ........................................................................................................7
2.4.2 Without Grounding Bar ..................................................................................................8
Chapter 3 Physical Connection....................................................................................................9
3.1 Connecting RJ45 Port ...............................................................................................................9
3.2 Connecting 1000M Combo Port...............................................................................................9
3.3 Checking the Cabling..............................................................................................................10
3.4 Powering on Switch................................................................................................................10

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
ii
Quick Start Guide
About this Manual
The Manual includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version in the company website.
Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY
WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
iii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at
his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of
as unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed
of as unsorted municipal waste in the European Union. See the product documentation
for specific battery information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return
the battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
iv
Applicable Models
This manual is applicable to POE-SW1602N, POE-SW2402N series switches.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
During the installaon and ulizaon of the device, please strictly conform to electrical safety
rules in different naons and regions.
The device must be installed in machine room only, and only maintenance staffor qualified
person should access to the device.
Do not touch the upper cover area of the device that may be overheated.
Power must be shut down during cable connecon, device installaon and dismantlement.
You shall acknowledge that the use of the device with Internet access might be under network
security risks, please strengthen protecon for your personal informaon and data security. If
you find the device might be under network security risks, please contact with us.
Proper configuraon of all passports and other security sengs is the responsibility of the
installer, and you shall keep user name and passports properly.
The AC power supply has double pole/neutral fusing.
Symbol Description
Provides addional informaon to emphasize or supplement
important points of the main text.
Indicates a potenally hazardous situaon, which if not avoided,
could result in equipment damage, data loss, performance
degradaon, or unexpected results.
Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
1
Chapter 1 Introduction
1.1 Overview
POE-SWXX02N switches are layer 2 network switches used in the access of surveillance
network. The switches provide 16/24 10/100M RJ45 ports, 1000M combos, and support long-range
access up to 250 m. POE-SWXX02N switches support uplink aggregaon, increase uplink
bandwidth, and ensure reliable uploading of mul-channel video data. With high reliability,
convenience for installaon and maintenance, quick switch funcon, and mul-port, the switches
are applicable to device access in small-scaled local area network (LAN) or collecve uploading.
1.2 Packing List
Please refer to the packing list as below to check whether accessories with the switches are
complete or not.
If there is any damage or lack, take the original package and contact the dealer to change.
Table 1-1 Packing List of POE-SW1602N and POE-SW2402N
Name Item Quantity
Switch
1
L-shaped bracket
1
Power cord
1
Screw
4
User manual
1

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
2
1.3 Appearance
1.3.1 Front Panel
Front panels of POE-SW1602N and POE-SW2402N are shown as below.
Front Panel of POE-SW1602N
Figure 1-1 POE-SW1602N Front Panel
Front Panel of POE-SW2402N
Figure 1-2 POE-SW2402N Front Panel
Indicator
Indicators are used to monitor the status of switches. See the following table for the descripon of
the indicators.
Table 1-2 Indicator Descripon
Indicator Status Description
PWR
indicator
Solid The switch is powered on normally.
Unlit No power supply connected or power supply is abnormal.
G1/G2
indicator
Solid The 1000M combo is connected.
Flashing The 1000M combo is transming data.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
3
Unlit No 1000M combo connected or connecon is abnormal.
LINK/ACT
indicator
Solid The port is connected.
Flashing The port is transming data.
Unlit The port is disconnected or connecon is abnormal.
PoE indicator Solid The switch provides power supply to PD normally.
Unlit The switch is disconnected to PD, or provides power supply to PD
abnormally.
PoE-MAX
indicator Solid/Flashing The output power of the switch will reach the upper limit. The power supply may be abnormal if more devices are connected.
Unlit The switch provides power supply to PD normally.
DIP Switch
DIP switch can be switched to three statuses: standard model, extend model, and aggregaon
model.
Table 1-3 DIP Switch Model
Model Funcon
Standard The corresponding port supports network transmission of up to
100 m, and the speed rate of the port is 100 Mbps.
Extend
POE-SW1602N :Extend (9-16)
POE-SW2402N:Extend (17-24)
The 9 to 16 ports of POE-SW1602N and the 17 to 24 ports of
POE-SW2402N support IP transmission of up to 250 m, and the
speed rate of the port is 10 Mbps.
Aggregaon (G1-G2)
The aggregaon funcon of the corresponding port is enabled, and
the 1000M port link aggregates. The two physical ports become a
logical port with 2G bandwidth.
PoE Ports
100M PoE ports connect to other PoE devices with network cable.
Ensure that your devices powered via the PoE port have their shells protected and fire-proofed,
because the switches are not compliant with the Limited Power Source (LPS) standard.
1000M Combos
When connected to a network cable, the 1000M combo is a PoE port. When plugged into with
an opcal module and connected to an opcal fiber, the 1000M combo funcons as a fiber
opcal interface.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
4
When connected to both the network cable and opcal fiber at the same me, the port works
as a fiber opcal interface.
1.3.2 Rear Panel
Rear panel of POE-SW1602N and POE-SW2402N is shown as below.
Rear Panel of POE-SW1602N and POE-SW2402N
Figure 1-3 POE-SW1602N and POE-SW2402N Rear Panel
Grounding Terminal
The grounding terminal connects with ground cable in case of lightning. For details about
grounding, see secon Grounding.
Power Interface
Connect power interface of the switch with power socket by power cord, and use 220 VAC to
provide power to the switch.
Please use the original power cord to power up the switch.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
5
Chapter 2 Installation
2.1 Preventive and Cautionary Tips
Put on anti-static gloves before installation.
During the installation, power off your switch.
Use the attached power adapter or power cord to connect the switch to power supply.
The input voltage range must be consistent with the voltage range of the power adapter and
switch.
Ensure the switch is installed in a well-ventilated position.
Do not open or dismantle the shell of the switch.
Cut off power supply before cleaning the switch. Do not clean the switch with any liquid.
Keep the switch away from power line, electric light, and power grid.
2.2 Working Environment Requirements
2.2.1 Temperature and Humidity
In order to ensure normal working and operation life of the switch, room temperature and
humidity must be kept at certain level.
If room humidity is too high for a long time, insulating materials may be ineffective or even
lead to electricity leakage, mechanical performance of materials may change, and metal
components may be rust, etc.
If relative humidity is too low in the room, insulating gaskets may shrink, which leads to the
loosening of screws and static electricity, and damages circuit of your switch.
If room temperature is too high for a long time, insulating materials may be aging in a fast
speed, which substantially reduces the reliability of your switch and seriously impacts its
operation life.
2.2.2 Static Electricity Protection
Dust may lead to electrostatic adsorption. To protect the device from static electricity harm, pay
attention to the following requirements:
Keep the environment air clean. A regular dusting is necessary.
Make sure the device is grounded well.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
6
2.2.3 Lightning Protection
In thunderstorm weather, a sudden strong current may damage the switch. To protect your switch
from lightning strike or strong current, please:
Make sure the switch, rack, installaon desktop, and power socket on the wall all are
well-grounded.
Route the switch cables properly.
If you need to route cables outdoors, it is advised to use a lightning arrester.
2.2.4 Installation Position
No maer whether your switch is installed on a rack or desktop, follow the instrucons below:
Make sure the rack or desktop be stable and firm enough.
The room must be well-venlated. Keep at least 10 cm distance between all sides for cooling.
Do not place any heavy or big-size object on the switch.
Keep at least 1.5 cm vercal distance between each switch while installing it on a rack.
2.3 Installation
POE-SW1602N and POE-SW2402N switches support rack installaon. Follow the steps below for
rack installaon.
The following panel is the front panel of the switch. For details about the ports, see secon
Appearance.
Step 1 Check the grounding and stability of the rack.
Step 2 Use the aached screws to fix two L-shaped brackets to the sides of the switch.
Figure 2-1 Install L-Shaped Bracket
Step 3 Place your switch on the rack, fix it to the rack with self-prepared screws, and ensure the
stable installaon of your switch to the rack.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
7
Figure 2-2 Fix Switch to Rack
Do not place any heavy object on the switch in case of any incident.
Make sure sound cooling and ventilation.
2.4 Grounding
Purpose:
Grounding is used to quickly release overvoltage and overcurrent induced by lightening for switch,
and to protect personal safety. Select the appropriate grounding method according to your needs.
2.4.1 With Grounding Bar
If a grounding bar is available at the installation site, follow the steps below.
Step 1 Connect one end of the grounding cable to the binding post on the grounding bar.
Step 2 Connect the other end of the grounding cable to the switch grounding terminal and fix the
screw.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
8
Figure 2-3 Grounding with Grounding Bar
2.4.2 Without Grounding Bar
Purpose:
If there is no grounding bar but earth is nearby and the grounding body is allowed to be buried,
follow the steps below.
Step 1 Bury an angle steel or steel pipe (≥ 0.5 m) into the mud land.
Step 2 Weld one end of the grounding cable to the angle steel or steel pipe and embalm the
welding point via electroplating or coating.
Step 3 Connect the other end of the grounding cable to the grounding terminal.
Figure 2-4 Grounding with Angle Steel

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
9
Chapter 3 Physical Connection
3.1 Connecting RJ45 Port
Use a network cable to connect your switch to the RJ45 port of an opposite end device. The RJ45
port can connect with network camera, IP camera, NVR, switch, etc.
Figure 3-1 RJ45 Port Connection
3.2 Connecting 1000M Combos
This section uses dual-fiber SFP optical module as an example.
When connected to a network cable, the 1000M combo is a PoE port. When plugged into with an
optical module and connected to an optical fiber, the 1000M combo functions as a fiber optical
interface.
When connected to both the network cable and optical fiber at the same time, the port works as a
fiber optical interface.
Do not bend fiber optic (curvature radius ≥10 cm) overly.
Do not look directly at fiber optic connector because laser is harmful to eyes.

16/24-Port 100M Long-Range PoE Switch Quick Start Guide
10
Step 1 Connect the two paired SFP optical module with an optical fiber.
Step 2 Hold SFP optical module from one side, and smoothly plug it into the switch along with the
SFP port slot until optical module and the switch are closely attached.
Step 3 After powering on your switch, check the status of Link/Act indicator. If the indicator is lit,
the link is connected. If the indicator is unlit, the link is disconnected. Check the line, and
make sure opposite devices have been started. For more details, see section Indicator.
3.3 Checking the Cabling
Before powering your switch, make sure that:
The operating power supply is compliant with rated input standard.
Port cables and grounding cables are correctly connected.
If there is outdoor cabling, connect a lightning rod and lightening arrester to the cable.
Figure 3-2 Lightning Rod Connection
3.4 Powering on Switch
Please use the attached power cord to power up the switch.