Lucasey LC200WT User manual

LC200WT
Security Wall Mount with Tilt
for up to 32" Flat Screens
Caution: Improper installation of this mount may void the warranty on your monitor.
Caution: Wall attachment should be performed by qualified installers only, using construction methods prescribed
by authorized architects or engineers that comply to all applicable codes and standards.
The maximum weight of monitor to be installed on the LC200WT is 75 Lbs. (34.1Kg.)
Inspect all parts to make sure there is no shipping damage. Do not install if any parts are damaged.
Please call 1-800-LUCASEY or 1-510-534-1435 if you have any questions about this installation.
Important! Please read all warnings and cautions before installing the mount.
The LC200WT Security Wall Mount with Tilt is designed to
secure up to a 32" flat panel monitor to the wall while
still allowing the monitor to tilt.
The VESA® mounting patterns on the front of the
LC200WT allow it to be mounted to monitors that have
mounting patterns of 200mm x 100mm and 100mm x 100mm.
Convenient cutouts for electrical and A/V wiring in the wall.
The security screws provided with the mount can be used
to prevent easy removal of the monitor without having
the appropriate security tool (purchased separately).
Standard socket head screws are also provided to
mount the monitor without using the security hardware.
Our mounts are tested at four times the rated load
limit to ensure that they can hold the monitor during
seismic or other extreme loading events.
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
LC200WT INSTALLATION INSTRUCTIONS
LC200WT (8/07) ©2007 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Page 1 of 6

WARNING: Improper installation can result in serious personal injury. It is the responsibility of the installer to ensure
that all safety precautions are taken during the installation and that all safety features of the mount are properly utilized.
WARNING: The structure to which the mount is attached needs to be capable of supporting five times the stated load limit.
Additional reinforcement of the structure may be necessary and a certified architect
or engineer is needed to make this determination.
WARNING: Take into consideration the combined weight of the mount, the monitor and any auxiliary equipment when
determining the total load on the wall and mount.
WARNING: Do not place your fingers between movable parts on the LC200WT mount. The LC200WT Back Plate
and FSCT VESA® Mounting Plate, when adjusting the tilt or putting the monitor in place, create pinch points that can
cause injury.
WARNING: Make sure that the screws used to attach the monitor to the mount are the appropriate size and length. An
assortment of monitor attaching screws are provided for convenience. The appropriate screws to use for mounting the
monitor is determined by the monitor manufacturer. Failure to use the screws recommended by the monitor manufacturer
can result in the monitor dropping from the mount and/or damage to the electronic components inside the monitor.
Page 1 ... Title Page & Product Description
Page 2 ... Warnings, Item List & Tools Required
Page 3 ... Dimensional Drawings
Page 4 ... Installation Instructions forLC200WT Wall Plate
Page 5 ... Installation Instructions for Monitor Attachment
Page 6 ... Tilt Adjustment, Monitor Removal & Warranty
Table of Contents
Stud Finder
Drill with 1/8"Drill Bit
Phillips Screw Driver
1/4" Socket Driver w/ 1/4" Socket
1/4"Socket Extension 12" - 16"
5/32" Hex Driver for 1/4" Socket
(optional security tool 5/32" Hex
Driver with hole for 1/4" Socket)
6 ...
12 ...
6 ...
12 ...
6 ...
12 ...
6 ...
36 ...
6 ...
18 ...
6 ...
4mm x 25mm Set Screws
4mm Hex Nuts
5mm x 30mm Set Screws
5mm Hex Nuts
6mm x 30mm Set Screws
6mm Hex Nuts
4mm x 12mm Phillips Screws
5mm Flat Washers
5mm x 12mm Phillips Screws
1/4" Flat Washers
6mm x 12mm Phillips Screws
Monitor Attaching Screw Assortment
1 ...
1 ...
8 ...
4 ...
3 ...
LC200WT Wall Plate
LC200WT VESA® Mounting Plate
#10-24 x 1" Socket Head Cap Screws
#10-24 x 1/2" Button Head Screw with Security Pin
#14 x 2-1/2" HWH Lag Screws
Tools Required
Item List
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
LC200WT INSTALLATION INSTRUCTIONS
LC200WT (8/07) ©2007 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Page 2 of 6

10.2"
8.0"
3.0"
3.0"
4.0" 4.0"
3.85"
2.35"
LC200WT Back Plate
10.0"
8.0"
200mm
3.934
7.872
LC200WT VESA® Front
8°
3.6"
LC200WT Tilted
2.5"
LC200WT Side View LC200WT Isometric View
2.5"
LC200WT Top View
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
LC200WT INSTALLATION INSTRUCTIONS
LC200WT (8/07) ©2007 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Page 3 of 6

LC200WT Back
Electrical and/or A/V
wiring plug box cutout
#14 X 2-1/2" Lag Screws
Determine the best possible viewing location for your
monitor taking into account the tilt angle to be used.
Locate a wood stud using a stud finder in the location
where the monitor is to be mounted.
Note: The LC200WT can be mounted on the stud with
the mount centered or offset to the left or right 4".
(Optional Toggle Bolts are required for offset
installations or metal stud installations)
Use the LC200WT Back Plate as a template to mark
the locations for three pilot holes in the wood studs.
Drill 1/8" pilot holes in the three marked locations.
Use the provided #14 x 2-1/2" Lag Screws to attach
the LC200WT Back Plate to the wall.
Wood Stud Installation
This end up.
Metal Stud Installation
(Using optional WMATB3 Toggle Bolt Kit)
Determine the best possible viewing location for your
monitor taking into account the tilt angle to be used.
Locate a stud using a stud finder in the location
where the monitor is to be mounted.
Follow the instructions that come with the toggle bolt
kit to install the toggle bolt plastic retainers at
each of the three mounting hole locations.
Use the Screws provided with the toggle bolt kit
to attach the LC200WT Back to the wall.
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
LC200WT INSTALLATION INSTRUCTIONS
LC200WT (8/07) ©2007 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Page 4 of 6

Monitor Attaching Screws
Flat Washers
Monitor Attachment to Front Plate
Determine which type of monitor attaching hardware is required
for the monitor as specified by the monitor manufacturer. Various
sizes of monitor attaching screws are provided for convenience.
Make sure the top of the LC200WT Front is oriented in the same
direction as the top of the monitor. The holes on the side of the
LC200WT Front Plate are closer to the bottom edge than the top edge.
Align the LC200WT front plate with the VESA mount pattern on the
back of the monitor. Attach the LC200WT Front Plate to the back of
the monitor using the appropriate size screws and washers.
Make sure all of the Monitor Attaching Screws are tight before
proceeding with the rest of the installation.
LC200WT Front
This end up.
Security Screws
or Socket Head Screws
Socket Head Screws
with 1/2" of Thread Exposed
LC200WT Back
LC200WT Front
Mounting Slots
Screw four of the provided Socket Head Screws into the threaded
inserts closest to the monitor on the LC200WT Front. Leave 1/2"
of thread exposed.
With two people, lift the monitor, with attached LC200WT Front,
onto the LC200WT Back making sure that the Socket Head Screws
are engaging the Mounting Slots.
Using a long extension and the appropriate security socket tool
or socket head driver, insert the Tilt Adjusting Screws and Pivot
Screws into the threaded inserts farthest from the monitor.
Remove the Socket Head Screws, only after making sure the Tilt
Adjusting Screws and Pivot Screws are installed. Adjust the tilt
to the desired viewing angle and tighten all four screws.
Note: Security Screws and Socket Head Screws are provided for
convenience. Either can be used to safely install the mount.
Mounting Slots
Attaching Front Plate to Back Plate
Tilt Adjusting Screws
Pivot Screws
Remove Socket Head Screws
after Pivot and Tilt Screws
are installed.
Remove Socket Head Screws
after Pivot and Tilt Screws
are installed.
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
LC200WT INSTALLATION INSTRUCTIONS
LC200WT (8/07) ©2007 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Page 5 of 6

Monitor Removal
Adjust the monitor tilt to 0 and insert four Socket Head
Screws into the threaded inserts closest to the monitor.
Remove the Tilt Adjustment Screws and the Pivot Screws.
Lift the monitor with attached LC200WT Front and separate
the front from the back. Carefully set the monitor down and
remove the monitor attaching screws.
Socket Head Screws
Tilt Adjusting Screws
Pivot Screws
Socket Head Screws
LC200WT Back
LC200WT Front
Tilt Adjusting Screws
Pivot Screws
Tilt Adjustment
Loosen the Tilt Adjusting Screws
Tilt the monitor to the desired viewing angle.
Tighten the Tilt Adjusting Screws.
LUCASEY MANUFACTURING CORPORATION MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED except that the goods sold under this agreement
shall be free of defects in materials and workmanship for a period of one year from the user's date of purchase. User assumes all risk and liability
resulting from the use of the goods, whether used singly or in combination with other goods. Lucasey Manufacturing Corporation neither assumes
nor authorizes any person to assume for it any other liability in connection with the sale or use of the goods sold and there are no oral agreements
or warranties collateral to or affecting this limited warranty. Lucasey Manufacturing Corporation will repair or replace defective parts or equipment
within one year of the date of purchase, at its option, provided the part or equipment is returned pre-paid to Lucasey Manufacturing Corporation's
plant. The repaired or replaced part shall be shipped to the user, FOB Lucasey Manufacturing Corporation's plant. NO allowance for outside labor
charges are implied within the terms of this limited warranty. Under no circumstances will Lucasey Manufacturing Corporation be responsible for
special, indirect or consequential damages. The remedies set forth in this Limited Warranty are exclusive and the liability of Lucasey Manufacturing
Corporation with respect to any contract of sale or anything done in connection therewith, whether in contract, in tort, under any warranty or
otherwise shall not, except as expressly provided herein, exceed the price of the equipment or part on which such liability is based. Any damage
caused by the improper use, operation beyond capacity, substitution of parts or equipment not approved by Lucasey Manufacturing Corporation,
improper packaging, failure to observe installation or other instructions, transit, or repair by one other than Lucasey Manufacturing Corporation,
will not be covered by and shall void this Limited Warranty.
LIMITED WARRANTY
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
LC200WT INSTALLATION INSTRUCTIONS
LC200WT (8/07) ©2007 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Page 6 of 6