North Bayou MC27-2A User manual

D
a
5
B2.Install wall plate onto wood stud
b
Ф4mm
70mm+
NOT SUPPLIED
Step 1.
1.Use wall plate as guide ,mark 3 screws location on
wall.
Step2.
1.Use hand drill with 4mm drill bit (Not supplied), drill
hole on marked locations with 70mm+ depth.
Step3
1.Take wood screws and washers from pouch D, put one
each washer on wood screw, insert each through 3
wall plate screw holes and into drilled hole. Use socket
wrench (Not supplied) to tighten top screw first.
Check leveler and tighten the other respectively.
Ensure 3 screw are well tightened.
2.Cover up 3 screws by screw caps and you are done.
Leveler
Step 1.
1.Use wall plate as guide ,mark 3 screws location on
wall.
Step2.
1.Use hand drill with 10mm drill bit (Not supplied), drill
hole on marked locations with 70mm+ depth.
2.Take anchors from screw pouch E, insert anchor
into each hole and hammer it until flush with
wall surface.
Step3
1.Take wood screws and washers from pouch D, put one
each washer on wood screw, insert each through 3
wall plate screw holes and into anchor. Use socket
wrench (Not supplied) to tighten top screw first.Check
leveler and tighten the other respectively. Ensure 3
screw are well tightened.
2.Cover up 3 screws by screw caps and you are done.
Ф10mm
70mm+
a
E
b
D
ab
Leveler
NOT SUPPLIED
B1.Install wall plate onto
masonry or solid concrete
27-2AMC
By Hand
Adjustment
Tightening Direction
loosening Direction
Hex Wrench
Phillips Screwdriver
Pencil
Optional
Warning
Reminder
Ratchet Wrench
Hand Drill
Star Wrench
用手
调整
拧紧方向
拧 方向松
六角扳手
螺丝起子
铅笔
可选
警告
提示
套筒扳手
手电钻
安全扳手
Remove
移开
定点恒力加大
定点恒力减小
+
-
:Torque increased
:Torque reduced
+
-
:Torque increased
:Torque reduced
拧紧方向
拧 方向松
Tightening Direction
loosening Direction
NOTE
定点恒力加大
定点恒力减小
Max Load：13.2-26.4lbs(6-12kg)
4001080502 A1
180°
± °12
0~ 0~7.5"( 191mm)
0~2.4"(0~60mm)
+10°/-12°
0~ 0~18.9"( 480mm)
39.8"(1011mm)max
180°
26.4"(670mm)max
360°
456
9
8
7
Ф16× 1.5mmФ8.2×10-70
3mm 5mm
4mm
C
D E F
M4×15mm
A
4x
B
M5×12mm
B
4x
3x3x each 1x 1x 1x
4x
Ф7×70mm
Ф10× 1.0mmФ4.5×
2x
123
2x
Part List
Fits Most Displays Size:22"~27"
Max Load 13.2~26.4:Ibs (6~12kg)
VESA:75×75,100×100mm
Workstation Wall Mounted
Instruction Manual
Severe personal injury and property damage can result from improper installation or assembly.
Read the following warning carefully before beginning.
● Products must be installed by professional or installer.
● If you do not understand the instructions or have any concerns or questions, please
contact a qualified local installer.
● Do not install or assemble if the product or hardware is damaged or missing, if you
require replacement parts, please contact you local distributor for assistance.
● This product fits most 22"-27" LCD / monitor; maximum weight of LCD / monitor:
12kg / 26.4lbs.
● Installer-friendly and straight forward.
● For safe installation, the desk you are mounting to must support minimum 3 times the
weight of the total load (the mount, the monitor and all accessories weight).
● Do not use this product for other than the original designed.
● This product contain moving parts, please use with caution.
● When installing monitor, please do not damage electrical wiring or power source.
● Installation and routing of monitor cables on the monitor bracket must comply with
electro-technical regulations.
● Importantly, mains- and data-cables must be secured against twisting and squeezing or
shearing.
● The manufacturer will bear no responsibility to the desk of mounting, or incidental
or consequential damages arising thereof.
● The manufacturer disclaims any liability for the modifications, improper installation, or
installation over the specified weight range. The manufacturer will not be liable for any
damages arising out of the use of , or inability to use, the product.
● This product is designed for indoor used only, use of this product outdoor could lead to
product failer and severe personal injury.
▲ This product contains a high pressure gas spring, fire and percussion are prohibited. Also
it is strictly prohibited to dismantle without professionals. Please return to the manufacturer
or hand over to professional agencies if the product is abandoned. In order to ensure
the performance of gas spring, full direction adjustment of the product arm is recommended
several times per month.
A、Full adjustment after installation
Symbols

a
b
2
3
4
1
2
3
4
5
6
66
9
2
2
Tighten set screw
flush with surface.
Q. Product unable to adjust manually during free state?
A. Full product must be assembled and installed onto wall plate to
gain support in order to move arm upright or down.
Q. Product cannot hovered as it is during upright or down
movement after Installed?
A. Monitor must be installed and pressure (Torque) must be
readjust (Refer to G torque adjustment).
Q. When monitor is at the max upright or position after Installed?
A. Pressure (Torque) must be re-adjust (Refer to G adjustment).
Q. What size of drill bits used for masonry, concrete wall and wood
stud?
A. Used diameter 10mm drill bits for masonry or concrete wall.
Diameter 4mm for wood stud . Holes depth must be than
60mm+.
To adjust pressure torque , Arm 1 must be held down
and adjusting screw then appeared for adjustment.
F
() 5mm
-12°
+12°
①
③②
F
（3mm）
-12°
+12°
F
（3mm）
①
②
360°
1
2
4
5
1
3
（5mm）
F
（5mm）
F
（5mm）2
F
F
(3mm)
F
(3mm)
5
F
(3mm)F (3mm)
3
4
D、Display height adjustment
G、Torque adjustment
"+": Torque increase direction shown fig-1
"-": Torque decrease direction shown fig-2
Notes：Ensure display weight is within load range.
If display and keyboard tray can be hovered at any height after
display installed. No adjustment needed.
1.
If display and keyboard tray rise up automatically after display
installed, adjust the following: One man hand press down the
screen,the other wind set screw at the bottom of upper arm
at joint to ' – ' direction to reduce torque by using F, 5mm.
Allen key as shown in Fig-1 and Fig-2 until display and keyboard
tray can be hovered at any point of positions.
2.
C、Workstation assembly & installation H、Display rotation
I、Keyboard tray extends adjustment
J、Keyboard tray angle adjustment
F、Power and display lines installation
Declind adjustment:
Inclined adjustment:
①Turn screw anti-clockwise direction using 3mm Allen key D to
release. ②Turn screw clockwise direction using 3mm Allen key
D to tilt upright angle.③Turn screw clockwise direction using
3mm Allen to tighten and secure set angle.
①Turn screw anti-clockwise direction using 3mm Allen key D to
tilt down side angle.②Turn screw clockwise direction using
3mm Allen to tighten and secure set angle.
Inclined adjustment Declind adjustment
Warning:
Ensure screws are
secured firmly.
Tighten set screw
flush with surface.
b
a
Loosen screw but
not drop off.
Loosen screw but
not drop off.
K、Common Q & A.
I f d i s p l a y a n d k e y b o a r d t r a y a t t h e l o w e s t p o s i t i o n a f t e r
installation, repeat #2 procedures but winding set screws to ' + '
direction to increase torque as Fig-1 and Fig-2 until display and
keyboard tray can be hovered at any point of positions.
3.
E. Display installation
Warning:
Ensure screws are
secured firmly.
Note：
The pre-sre force is
at the medium.
9