luceco Mosi series Manual

Tech Help Line
UK - 0845 194 7584
Non UK - [phone]
Visit our website at
Luceco is a registered trade mark of Nexus Industries Ltd.
Supplied by
BG Electrical Ltd
Stafford Park 1 TF3 3BD ENGLAND www.luceco.co
LED IP65 Mosi Bulkhead
PART CODE: LBM290W11S40, LBM290B11S40,
LBM200W6S40, LBM200B6S40
Installation & Operating Instructions
SPECIFICATIONS
• Suitable for use with Mains voltage of 220-240V AC
• This product must be disconnected before insulation
resistance testing of the lighting circuit
• Check for electrical cables and pipes before installation
NOTE – To comply with regulations, installation must be carried
out by qualified electrician and in accordance with the current IEE
Wiring Regulations (BS7671) and Building Regulations.
ENSURE ELECTRICAL SUPPLY IS DISCONNECTED/ISOLATED
BEFORE COMMENCING INSTALLATION
• To maintain the IP65 rating of the bulkhead, a suitable 20mm
cable gland should be used in conjunction with rubber
insulated cable to ensure the supply cable is sealed in the
gland. Failure to use a gland and/or rubber insulated cable
may result in water ingress
Page 1
SUGGESTED METHOD OF INSTALLATION
The bulkhead is designed for mounting in any of the
following options: –
• Surface Wall Mounting
• Surface Ceiling Mounting
1. Surface mounted options may use rear cable entry for flush
mounting or there is facility for surface Conduit ‘besa’ box
mounting or side conduit entry. (Image 1)
2. With the method of mounting chosen, remove the front
Diffuser, by undoing the three front Screws. (Image 2)
3. To remove LED tray, loosen two retaining screws,
and twist tray clockwise and remove. (Image 3)
4. This Bulkhead can be mounted on ceilings and vertical walls.
Ensure the mounting surface is suitable for installation. Once
mounting points are decided, drill out mounting holes and any
cable entry points needed.
5. Cable Entry Points must be drilled out with a 20mm bit, cleaned of
any loose burrs and fitted with a suitable IP65 gland, if the IP65 rating
is to be maintained. Otherwise the IP rating would be reduced.
4
1
cable entry
points
cable entry
points
2
loosen
screws here
3
loosen
screws here
CRI
80
>
IP65
RATED 3
GUARANTEE
year
650
LUMINAIRE
LUMENS
Code Rated Voltage Power Current PF
Lumens with
no diffuser
Lumens with
diffuser
LBM20X6S40 200-240V 9W 45mA >0.8 850 Llm 650 Llm
LBM29X11S40 200-240V 14W 67mA >0.8 1400 Llm 1100 Llm
TECHNICAL INFORMATION
THIS LUMINARE CONTAINS NO USER REPLACEABLE COMPONENTS.

WIRE UP
With the bulkhead securely fixed in the desired position,
make the electrical connection to the terminal block,
observing the correct polarity. (Image 5)
Note – the bulkhead is a class II construction and does not
require an earth connection, but a earth termination point is
fitted.
Once the electrical connections have been made, the gear
tray can be fitted back into position and secured by twisting
Anti-clockwise and tightening the 2no. Fixing screws.
Re-fit the front diffuser and tighten 3 securing screws. Turn
on power and operate. (Image 7)
56
tighten
screws here
Page 2
Tech Help Line
UK - 0845 194 7584
Non UK - [phone]
Visit our website at
Luceco is a registered trade mark of Nexus Industries Ltd.
Supplied by
BG Electrical Ltd
Stafford Park 1 TF3 3BD ENGLAND www.luceco.co
Installation & Operating Instructions
Environmental Protection W.E.E.E
This symbol is known as the “crossed-out wheelie Bin Symbol”. When this symbol is marked on a product or battery, It means that
it should not be disposed of with your general household waste. Some chemicals contained within electrical/electronic products or
batteries can be harmful to health and the environment. Only dispose of electrical/electronic/battery items in separate collection
schemes, which cater for the recovery and recycling of materials contained within. Your co-operation is vital to ensure the success of
these schemes and for the protection of the environment
WARRANTY
Products are protected by warranty for a period of 3 year warranty from date of purchase against defects in material and workmanship
(unless otherwise stated). Should a product fail to perform as described within the warranty period it will be repaired or replaced with
the same or equivalent product by Luceco, free of charge provided that you: (1) return the product to us with shipping charge prepaid,
(2) provide us with proof of the original date of purchase and (3) quote our return authorization number
Repaired or replaced products will be returned to you with shipping charges prepaid. Replacement products may be refurbished
or contain refurbished materials. If in our sole discretion, we are unable to repair or replace a defective product, we will refund the
purchase price of the product
This warranty will not apply if in our judgment, the product fails due to damage in shipment, handling, storage, accident, abuse or
misuse, or if it has been used in a manner not conforming to our product instructions, has been modified in any way, or has any serial
number removed or defaced. Repair or attempted repair will void this warranty. Our maximum liability under the terms of this warranty
is limited to the purchase price of the product covered by the warranty
The warranty is given under English Law. If any part of this warranty is deemed unenforceable (including any provision in which we
exclude our liability to you) the enforceability of any other parts of the warranty will not be affected. These terms do not reduce your
statutory rights
THESE TERMS AND CONDITIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
For further details, terms and conditions and online registration please see www.luceco.co