Luma Surveillance Turret 710 Series User manual

710 Series Bullet
510 Series Bullet
310 Series Bullet
HD Analog Surveillance Camera
Installation &
Operation
Manual

2
Luma 310/510/710 Series Bullet Camera
Box Contents
}Camera
}Self-adhesive mounting template
}4 x wall anchors with screws
}3mm hex wrench
}CC tester cable
Required Equipment
Aside from the contents of this box, you will need to provide
}Phillips screwdriver
}Power source: either 12V DC or 24V AC
}CC-TV tester (recommended)

3
Luma 310/510/710 Series Bullet Camera
Inspection
Ensure that the device is in good condition and all the assembly parts are included.
We recommend installing with RG-59 or RG-6 cabling with two-wire power (either regular or
siamese). This provides better performance over distance than using traditional category cable
with baluns. For more details, see the product page at SnapAV.com.
}Make sure that all equipment is powered off during installation.
}Ensure the wall is strong enough to withstand three times the weight of the camera and
the mount.
}If the mounting surface is cement, use the included expansion screws to install the
camera. If mounting to a wood surface, use self-tapping wood screws (not included) to
secure the camera.
}If the product does not function properly, please contact technical support. Do not
disassemble the camera for repair or maintenance.
WARNING: This product can expose you to chemicals including cadmium, which
is known to the State of California to cause cancer. For more information go to
www.P65Warnings.ca.gov.

4
Luma 310/510/710 Series Bullet Camera
Overview
Before installing, familiarize yourself with the parts of your camera.
Access Panel
Sunscreen
Adjustment
Screw
Sunscreen
Lens
(square on
the 710)
IR Emitters
Mounting
Anchors

5
Luma 310/510/710 Series Bullet Camera
Prepare for Installation
1. Drill a cable hole and pilot holes for your screws in the ceiling, using the supplied
template.
2. If you are installing this camera in an older system that does not support HD-TVI,
unscrew the access panel cap on the bottom of the camera, and flip the camera’s
resolution toggle, shown below, to the CVBS position.
Video Test Port
(300 series has no
local test power)
OSD Joystick
Resolution
Toggle

6
Luma 310/510/710 Series Bullet Camera
Install the Camera
1. Route the cables through the cable hole.
2. Attach the base of the camera to the ceiling and secure it with screws.
3. This camera has an elbow joint flanked by two rotational joints for perfect pan
and tilt control. Loosen the three hex screws in the camera. Adjust the angle of the
elbow as desired, and tighten the elbow hex screw, A. Rotate the camera so that
it’s facing in the proper direction, and tighten the base screw, B. Finally, spin the
camera casing so that the picture is level, and tighten the level hex screw, C.
Level Screw C Elbow Screw A
Base
Screw
B

7
Luma 310/510/710 Series Bullet Camera
Adjust the Camera
1. Optional: If this is an HD installation and you want to use the camera’s on-screen
display through your DVR or the web interface, go into the DVR’s menu and set the
camera protocol to HIK-C (Coaxitron). To do so from the DVR’s local interface, go to
Settings > Camera > PTZ, then click the PTZ Settings button. From the web interface,
go to Configure the Recorder > Camera Settings > PTZ Settings. If this is a 960H
installation, you can only use the OSD menu locally at the camera.
2. Adjust or remove the sunscreen. You can slide the shade back and forth by loosening the
screw slightly; tighten when finished. You can remove the sunscreen by removing the
screw, then removing the shade; then replacing the screw when finished. Do not remove
the sunscreen unless the camera is never in direct sunlight, and only if the camera is
angled down so dust does not get on its lens.
3. If necessary, adjust the camera’s zoom and focus by using the OSD and the joystick (see
page 5). See our website for a manual covering operation of the in-camera menu.
4. If you want to adjust the camera settings using a CC tester, do that now (see the OSD
manual on our website). Otherwise, use the DVR’s controls to adjust the camera settings.

8
Luma 310/510/710 Series Bullet Camera
Support
Need Help? Contact Tech Support!
If you need further clarification, please email [e-mail]. For more information,
instructional videos, support documentation, or ideas, visit our website and view your
item’s product page.
5-Year Limited Warranty
This Luma Surveillance™ product has a 5-Year Limited Warranty. This warranty includes
parts and labor repairs on all components found to be defective in material or workmanship
under normal conditions of use. This warranty shall not apply to products that have been
abused, modified or disassembled. Products to be repaired under this warranty must be
returned to a designated service center with an assigned return authorization (RA) number.
Contact technical support for an RA number.
Copyright ©2015–2019 by SnapAV. All rights reserved. SnapAV, Luma Surveillance, and all
related marks and images are trademarks or registered trademarks of SnapAV.
Version 181204-2010