Lumantek VENTUS-A+ User manual

VENTUS-A+ DTV Analyzer / Manual v 1.2.3.0a
Updated Jan. 2016
Chapter No. 1-4
Manual
VENTUS-A+ DTV Analyzer
USB DTV Analyzer –ATSC/QAM/DVB-T2/DVB-T/DVB-C

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 2
VENTUS-A+ DTV Analyzer Manual
Revision Number: 1.2.3.0a
Distribution Date: Jan. 2016
Copy Rights
Copyright © 2006~2015 LUMANTEK Co., Ltd.
All Rights Reserved
This document contains information that is proprietary to LUMANTEK.CO., LTD. The
information in this document is believed to be accurate and reliable; however, LUMANTEK
assumes no responsibility or liability for any errors or inaccuracies that may appear in this
document, nor for any infringements of patents or other rights to third parties resulting from
its use.
This publication may contain technical issues, inaccurate information or typos. These will be
revised in revised edition, if there is any. No part of this publication is subject to be reproduced,
stored in retrieval system, or transmitted in any forms, or any means without the prior consent
by Lumantek.
Trademarks
HD ENCODULATORTM, SD ENCODULATORTM LUMANTEK Logo, Mega CruiserTM, ORIXTM, X-
CruiserTM, DTA-PlusTM, Media BlasterTM, are Trademarks of Lumantek. Co., Ltd.
Any other trademarks than stated above in this document belongs to its pertinent corporation.
Warranty Period
Lumantek’s products comes with One(1) year limited warranty. Please contact below if you
need more information. .
LUMANTEK CUSTOMER SERVICES
[e-mail] / TEL:[phone] / FAX:[phone]

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 3
Contents
1. Introduction -------------------------------------------------------
1.1 Features
1.2 Specification
1.3 Software Specification
2. VENTUS-A Plus System Package -------------------------
2.1 Parts Name
2.2 Package Contents
3. Installation --------------------------------------------------------
3.1 Software Installation
3.2 Driver Installation
4. DTV Analyzer Software ---------------------------------------
4.1 Control Window
4.2 Analysis Window –Services Tab
4.3 Analysis Window –PID Tab
4.4 Analysis Window –Table Tab
4.5 Analysis Window - Service View Tab
4.6 Analysis Window –Bit-Rate Tab
4.7 Analysis Window - TR 101 290 Tab
4.8 Analysis Window –Table History Tab
4.9 System Message & TR101290 Summary Window
4.10 TR 101 290 Summary Tab
4.11 RF Status Window
4.12 Operation Status Window
APPENDIX A. TR 101 290 Analysis Criteria
** Specification Sheet ------------------------------------------------
4
4
5
5
6
6
6
7
7
11
13
14
32
33
34
35
40
43
45
48
49
50
51
52
55

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 4
VENTUS-A+ DTV Analyzer
USB type DTV Analyzer for ATSC/QAM/DVB-T2/DVB-T/DVB-C
1. Introduction
VENTUS-A DTV Analyzer is designed to analyze MPEG-2 TS stream in real time/off line bases,
Hardware and Software as in a package. The Hardware interlocks with the PC via USB cable to
maximize its utilization as a mobile analyzer. Furthermore, it supports TS file output through
ASI and real time input can re-transmitted via ASI.
1-1. Features
①Real time analysis via RF/ASI/IP input plus offline analysis via TS files
②ETSI TR 101 290 based error detection
③Bit-rate, PTS-PCR, DTS-PCR measurement, Table repetition cycle analysis
④Provide configuration information for each PID, Service and Table
⑤Provide Table History and detailed Table analysis tool
⑥Provide Media player and detailed analysis information for each services
⑦Load/Save TS recording & Analysis log
⑧Support the newest TTA standard (Korean type 3D TV and multi-channel service)
⑨Provide MER/Packet error rate and receiver sensitivity during RF reception

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 5
1.2 Specification
•Demodulation : 8VSB, OpenCable(64QAM, 256QAM)
•Size : 154mm x 76.8mm x 28.4mm
•USB 2.0 bus powered, no power supply required.
•RF input connector : 75Ω F-Type 1ea
•ASI/SMPTE310M input connector : 75Ω BNC 1ea
•ASI/SMPTE310M output connector : 75Ω BNC 1ea
•ASI input bit-rate : 0~108Mbps
•ASI output bit-rate : 0~108Mbps
•SMPTE310M input bit-rate : 19.392Mbps
•SMPTE310M output bit-rate : 19.392Mbps
•RF Input Frequency Range : 40 ~ 1002 MHz
•RF Input Level : +7 ~ -84 dBm +6~ - 75 dBm(64QAM), +6 ~-66dBm(256QAM)
1.3 Software Specification
•TS input : ASI, SMPTE310M, File, IP(UDP/TS or UDP/RTP/TS), RF
•TS output : ASI or SMPTE310M (Not supported in IP Input, high speed analysis mode)
•Analysis mode : MPEG-2, ATSC, DVB
•Analysis Result Window
•Service, PID, Table, Service View, Bit-rate, TR 101 290, Table History
•Minimum System Requirements
•CPU : Intel Core i3 3.1GHz (Sandy Bridge) or above
•RAM : 2GB or above
•OS : Window 7
•Resolution : 1680x1050 or above

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 6
2 VENTUS-A Plus System Package
2.1 Parts Name
RF Input Port
LED Status lamp
ASI/SMPTE Input Port
ASI/SMPTE Output Port
USB 2.0 Port
2.2 Package Contents
DTV Analyzer USB Connection Cable
USB Memory
(w/ Software installation file)

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 7
Please disconnect USB cables from the DTV analyzer before installation.
Run ‘DTV Analyzer Setup’ file in the USB memory provided with the package. Press ‘Next’ to
proceed installation. (Run under ‘Administrator Authority’ for Windows OS 7 or above)
3 Installation
3.1 Software Installation

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 8

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 9
If you see below messages, please select ‘Do not close the application’

VENTUS-A+ DTV Analyzer / Manual
Chapter No. 1-4 10
After the installation is completed, the ‘WinPcap’ file needs to be installed. This must be
done during the installation, no reinstallation required for version updates.
Automatically start the WinPcap
driver at boot time’ must be
selected during the installation.
After the software installation is
completed, the Driver will
automatically start its installation
when the hardware is connected.
If not, please run ‘3.2 Driver
Installation’.