LWA FRAZIER 74480 User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
74480
QUEEN BED
FRAZIER

PRE-ASSEMBLY PREPARATION
2
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
7.Assembly is to be carried out by a competent adult(s) ONLY
8.During assembly, children should be kept away from the product due to possible risk to
injury.
9.Do not use this item if any components are missing or damaged.
10.Please keep the instructions for future reference.
Allow 40 min
For 2 people

3
PARTS LIST
1
Head Board x 1pc
7
Centre Support Leg x 2pcs
2
Side Rail (L&r) x 4pcs
8
Centre Support Leg x1pc
3
Foot Board x 1pc
9
Siderail Support Leg x 2pcs
4
Centre Support Rail x 2pcs
10
Center Cross Bar x 1pc
5
HB/FB leg x 4pcs
11
Wood Side Rail Bar x 4pcs
6
Slat x 14pcs

4
STEP 1:
•Prepare a protected surface with a blanket or cardboard.
•Attach 2x HB/FB Legs(5) to the 1x Head Board(1) and 2x HB/FB
Legs(5) to the 1x Foot Board(3), as shown below.

5
STEP 2:
•Attach the 4x Wood Side Rails Bars(11) to the 4x Left and Right
Siderails(2), Use 3x Bolt(E) and 3x Flat Washer(G) per bar,
threaded from the top and fasten with allen key(I).
•Attach the 2x Side Rails Support Legs(9) to the 4x Left and Right
Siderails(2), as shown below. Use 4x bolt(C) and 4x Flat
Washer(G) per leg, threaded from the top. Fasten with allen
key(I). Ensure the connection is tight.

6
STEP 3:
•Connect a side rail to the Head Board and Foot Board. Secure
with 2x bolt(A) and 2x Lock Washer(D) & 2x Flat Washer(F) per
corner. Fasten with allen key(H).
•Repeat for the other side rail.

7
STEP 4:
•Attach the Center support leg(8) to the 2x Centre Support Rail(4),
as shown below. Use 2x bolt(A) with 2x Lock Washer(D) & 2x Flat
Washer(F). Fasten with allen key(H).
•Attach the 2x supports(7) to the Centre Support Rail(4), as shown
below. Use bolt(A) with Lock Washer(D) & Flat Washer(F) per leg,
threaded from the top. Fasten with allen key(H).

88
STEP 5:
•Attach the Centre Support Rail(4) to the Head Board(1) and the
Foot Board(3), as shown as below. Thread bolt(A) with Lock
Washer(D) & Flat Washer(F) from the top into the holes at the
middle of the Head Board and Foot Board. Fasten with allen
key(H).

9
9
STEP 6:
•Attach the Center Cross Bar(10) to the Centre Support Rail(4)
on the middle, as shown below. Use 1x bolt(B) with Lock
Washer(D) & Flat Washer(F). Fasten with allen key(H).
•Attach either end of the center cross bar(10) to the side rails
(2). Use 2x bolt(A) with 2x Lock Washer(D) & 2x Flat Washer(F).
Fasten with allen key(H).

10 10
STEP 7:
•Flatten the 14x slats (6) on the bed frame. Assembly is finished.

11
11
Assembly Is Complete

12
12
PRODUCT CARE:
FURNITURE / BED
1. When assembling your bed please ensure that you have checked the
contents for all relevant parts.
2. When tightening bolts make sure that they are fully tightened but not
forced.
3. When moving your fully assembled bed you must first remove the
mattress and lift the frame into position, take care when lifting and
always have two people handling the bed. PLEASE DO NOT DRAG THE
BED as this will cause damage to the rail.
4. It is advisable to use approved cleaning products when cleaning the
furniture and bed frame as certain chemical based cleaners could have
an adverse effect on the bed finish.