WAGO I/O SYSTEM 750 Service manual

Pos: 2/ Do ku ment ati on all ge mein /Ei nba nd/ Einb and H a ndb uch -D ec kbl att ohne Varia nt enfel d ( S tan dar d) @ 9\mod_1285229289866_0.doc@64941 @ @ 1
Quickstart Reference
WAGO-I/O-SYSTEM 750
ETHERNET Programmable Fieldbus
750-880
10/100 Mbit/s; digital and analog signals
Version 1.0.0
Pos: 3/ All e S eri en (A llg em eine M od ule) /Hi nw eise zur D ok umen tati on/ Impr essu m für St andar dhan dbüch er - allg . Angab en, Ansc hrifte n, Telef onnu mmern un d E-Mail-A dress e n @ 3 \mod_1219151118203_21.doc@ 21060@ @1

2 WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
© 2012 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]om
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]om
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende d er Liste f ür T e xtmar ke E inb and _v orne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 5/ Do ku ment ati on all ge mein /V erzei ch niss e/I nhal ts verz eich nis - o hne Gli eder ung - und Ver zeic hni s @ 3\mod_1219151230875_21.doc @ 21063@ @ 1
Table of Contents
1Notes about this Documentation................................................................. 4
1.1 Validity of this Documentation................................................................. 4
1.2 Copyright................................................................................................... 4
1.3 Symbols..................................................................................................... 5
1.4 Number Notation....................................................................................... 7
1.5 Font Conventions ...................................................................................... 7
2Important Notes........................................................................................... 8
2.1 Legal Bases ............................................................................................... 8
2.1.1 Subject to Changes............................................................................... 8
2.1.2 Personnel Qualifications....................................................................... 8
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions...... 8
2.1.4 Technical Condition of Specified Devices........................................... 9
2.2 Safety Advice (Precautions).................................................................... 10
3Quickstart Description .............................................................................. 12
3.1 Hardware Design..................................................................................... 12
3.2 Preparatory Measures.............................................................................. 16
3.2.1 Download documentation and sample projects.................................. 16
3.2.2 Installing WAGO-I/O-PRO................................................................ 16
3.2.3 Starting Up the ETHERNET Network............................................... 22
3.2.3.1 Determine the IP address of your PC and change it if required .... 23
3.2.3.2 Assigning an IP address to the fieldbus controller ........................ 25
3.2.3.3 Testing the ETHERNET link......................................................... 27
3.2.4 Installing the USB Driver................................................................... 28
4Application example: Starterkit880_App1_FUP.pro............................. 30
4.1 Open project............................................................................................ 31
4.2 Configure hardware................................................................................. 31
4.3 Main Program "PLC_PRG" .................................................................... 35
4.4 Subprogram "Blink"................................................................................ 36
4.5 Subprogram "UserLED" ......................................................................... 38
4.6 Commissioning ....................................................................................... 42
4.6.1 Configuring a Communication Driver for an ETHERNET Link....... 42
4.7 Configuring a Communication Driver for a USB Link .......................... 44
4.7.1 Starting the Program........................................................................... 46
4.8 Visualization ........................................................................................... 47
4.8.1 Opening Visualization via the WAGO-I/O-PRO Software................ 47
4.8.2 Opening Web Visualization in the Internet Browser ......................... 48
4.8.3 Operating the Visualization................................................................ 49
List of Figures...................................................................................................... 50
List of Tables........................................................................................................ 52
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

4 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 7/ All e S eri en (A llg em eine M od ule) /Üb ers chr ifte n für all e S erie n/Hi n weis z ur D oku ment ati on/ Hin weis e z ur D o kume ntati on - Ü b erschr if t 1 @ 4\mod_1237987661750_21.doc @ 29029@ 1 @ 1
1 Notes about this Documentation
Pos: 8/ Ser ie 750 ( WAGO -I/O-SY STEM) /Hi n weis e zur Do kume ntati on /G ültig keit sb ereic h D ok ume ntati on Koppl er /Cont rol ler 750-xxxx,ohneVariantenangabe@ 4\mod_1239095911562_21.doc @ 30110@ 2@ 1
1.1 Validity of this Documentation
This documentation is only applicable to the 750-880 ETHERNET Programmable
Fieldbus of the WAGO-I/O-SYSTEM 750 series.
Pos: 9.1 / Alle Seri en ( Allg em ein e M odule) /H in weise zur Doku ment ati on/U rh eber sch utz ausf ührli c h @ 4 \mod_1235565145234_21.doc@ 27691@ 2 @ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 9.2 /D o kume ntati on allge mei n/Gl ie deru ngs el ement e/---S eite nwec hsel--- @ 3\mod_1221108045078_0.doc@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 9. 3/ Alle S erien (A llge meine M odule) /Üb erschr iften für all e Serie n/Hi nweis zur Dokumentation/Symbole- Ü bersc hrift 2 @ 13\mod_1351068042408_21.doc @ 105270@ 2 @ 1
1.3 Symbols
Pos: 9.4. 1 / Alle Seri en ( All ge mei ne M od ule) /Wi c htig e Er l äuter ung e n/Si cher hei t s- un d s onsti ge H in weis e/G efa hr/ Gefa hr: _War nung vor P ers on ensc hä den al lg em ein_ - Er läu ter ung @ 13 \mod_1343309450020_21.doc@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 9.4. 2 / Alle Seri en ( All ge mei ne M od ule) /Wi c htig e Er l äuter ung e n/Si cher hei t s- un d s onsti ge H in weis e/G efa hr/ Gefa hr: _War nung vor P ers on ensc hä den d urc h el ektr isc hen Str om_ - Erläuterung@ 13\mod_1343309694914_21.doc@ 101030@ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 9. 4.3 /Al le Seri en (Allg emei ne Modul e)/Wi chtig e Erl äuter ungen/ Sic her heit s- u nd s ons tig e Hi nweis e/ War nu ng/W arn ung : _W arn ung vor P erso nens ch äde n al lg emei n_ - Er l äuter ung @ 13\mod_1343309877041_21.doc@ 101035@ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 9.4. 4 / Alle Seri en ( All ge mei ne M od ule) /Wi c htig e Er l äuter ung e n/Si cher hei t s- unds onstig e Hi nweis e/ Vor sic ht/V orsi cht : _ War nung vor Pers one nsc häd en all ge mein _ - Erläuterung@ 13\mod_1343310028762_21.doc @101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 9.4. 5 / Alle Seri en ( All ge mei ne M od ule) /Wi c htig e Er l äuter ung e n/Si cher hei t s- un d s onsti ge H in weis e/Ac ht ung/ Ac htung : _ War nung vor Sachs ch äde n al lgem ei n_ - Erläuterung@ 13\mod_1343310134623_21.doc @ 101041@ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 9.4. 6 / Alle Seri en ( All ge mei ne M od ule) /Wi c htig e Er l äuter ung e n/Si cher hei t s- un d s onsti ge H in weis e/Ac ht ung/ Ac htung : _ War nung vor Sachs ch äde n dur ch elek tros tatis che Aufladung_- Er l äuter ung @ 13\mod_1343310227702_21.doc @ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 9.4. 7 / Alle Seri en ( All ge mei ne M od ule) /Wi c htig e Er l äuter ung e n/Si cher hei t s- und sonstigeHi nweise/Hinweis/Hinweis:_Wichtiger Hinweis allgemein_- Eräuterung @ 13\mod_1343310326906_21.doc@ 101047@ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 9.4. 8 / Alle Seri en ( All ge mei ne M od ule) /Wi c htig e Er l äuter ung e n/Si cher hei t s- un d s ons tig e Hi n weis e/In for m atio n/In for m atio n: _ W eit ere I nfor m atio n al lg emei n _ - Erl äuter ung @ 13\mod_1343310439814_21.doc@ 101051@ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 9.5 /D o kume ntati on allge mei n/Gl ie deru ngs el ement e/---S eite nwec hsel--- @ 3\mod_1221108045078_0.doc@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 9. 6/ Alle S erien (Al lgem eine M odule) /Hin weise zur Do kument atio n/Zahl ens ysteme @ 3\mod_1221059454015_21.doc@ 21711@ 2 @ 1
1.4 Number Notation
Table 1: Number Notation
Number code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 9. 7/ Alle S erien (A llge meine M odule) /Hin weise zur Do kument atio n/Schr iftk onven tione n @ 3\mod_1221059521437_21.doc@ 21714@ 2 @ 1
1.5 Font Conventions
Table 2: Font Conventions
Font type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Programme\WAGO-I/O-CHECK
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 10 /D oku menta tion all gemei n/Gli eder ungselemente/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810@ @ 1

8 Important Notes WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 11 /A lle Ser ien (Al lge meine Mo dule)/ Übers chrif ten für alle S erien /Wich tige Er läuter ung en/Wi chtig e Erläut erung en - Über schr ift 1 @ 4\mod_1241428899156_21.doc@ 32170 @ 1@ 1
2 Important Notes
Pos: 12 .1 /All e Serie n( Allg emeine M odul e)/Wic htig e Erläut erung en/ Einlei tung Wic htig e Erläut erung en @ 3\mod_1221059818031_21.doc @ 21717@ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 12 .2 /All e Serie n( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erien /Wich tige Er läuter ung en/Rec htlic he Grun dlag en -Ü bersc hrift 2 @ 3\mod_1221060626343_21.doc @21726 @ 2 @ 1
2.1 Legal Bases
Pos: 12 .3 /All e Serie n( Allg emeine M odul e)/Wic htig e Erläut erung en/ Änderu ngs vorbehal t -Ü bersc hrift 3 und I nhalt @ 3\mod_1221060036484_21.doc@ 217 20 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos:12.4/Serie750(WAGO-I/O-SYST EM) /Wic htig e Erlä uteru ngen/P erson alqu alifi katio n 750-xxxx @ 3\mod_1224061208046_21.doc @ 24063@ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on Series 750 devices may only be carried out by
electrical specialists with sufficient knowledge in automation. The specialists
must be familiar with the current norms and guidelines for the devices and
automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos:12.5/Serie750 (WAGO-I/O-SYST EM)/ Wichti ge Erlä uteru ngen/ Besti mmu ngsge mäße Ver wend ung 750-xxxx @ 3\mod_1224064151234_21.doc@ 24070@ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Couplers, controllers and I/O modules found in the modular WAGO-I/O-
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to the actuators or higher-level control systems. Using programmable controllers,
the signals can also be (pre-) processed.
The components have been developed for use in an environment that meets the
IP20 protection class criteria. Protection against finger injury and solid impurities
up to 12.5 mm diameter is assured; protection against water damage is not
ensured. Unless otherwise specified, operation of the components in wet and
dusty environments is prohibited.
Operating 750 Series components in home applications without further measures
is only permitted if they meet the emission limits (emissions of interference)
according to EN 61000-6-3. You will find the relevant information in the section
on "WAGO-I/O-SYSTEM 750" "System Description" "Technical Data" in
the manual for the used fieldbus coupler/controller.

WAGO-I/O-SYSTEM 750 Important Notes 9
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 12 .6 /All e Serie n( Allg emeine M odul e)/Wic htig e Erläut erung en/T echnis cher Zu stan d der Ger äte - Ü b ersc hrif t 3 und I nhal t @ 3\mod_1221060446109_21.doc@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The components to be supplied Ex Works, are equipped with hardware and
software configurations, which meet the individual application requirements.
WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in
case of changes in hardware or software as well as to non-compliant usage of
components.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos:12.7/Dokumentationallgemein/Gliederungselemente/---Seit enwec hs el--- @ 3\mod_1221108045078_0.doc @ 21810@ @1

10 Important Notes WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 12 .8 /All e Serie n( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erien /Wich tige Er läuter ung en /Sic her h eits hin wei se - Ü bersc hrif t 2 @ 6\mod_1260180299987_21.doc@ 46724@ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 12 .9 /All e Serie n( Allg emeine M odul e)/Wic htig e Erläut erung en/ Sicher heits- u nd so nsti g e Hin weis e/ Einl eitu ng S ic herh eits hin wei se H ar dwar e @ 6\mod_1260180170493_21.doc @ 46720@ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 12.1 0.1 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en/Si cher h eits - und so nstige H inwei se/G efahr/ Gefa hr: Nicht an Ger äten u nter Sp annung arb eite n! @ 6\mod_1260180365327_21.doc@ 46727 @ @ 1
Do not work on components while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 12.1 0.2 / Ser ie 75 0 ( WAG O-I/O-SY ST EM)/Wi cht ig e Erl äu ter ung en/Si cher hei ts - undsonstigeHinweise/Gefahr/Gefahr: Einbau0750-xxxx nurin Gehäusen, Schränkenoder elektrischenBetriebsräumen!@ 6\mod_1260180556692_21.doc@ 46731@ @ 1
Installation only in appropriate housings, cabinets or in electrical operation
rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 12.1 0.3 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en/Si cher h eits - und so nstige H inwei se/G efahr/ Gefa hr: Unf allver hütung svor schr iften b eachte n! @ 6\mod_1260180657000_21.doc @46735 @ @ 1
Pos: 12.1 0.4 / All e S erie n (Al lge mei ne M o dul e)/ Wich tig e Er läu ter ung en /Sic her h eits- un ds onstig e Hinw eise/G efahr/ Gefa hr: Auf nor mgerec hten A nschlus s achte n! @ 6\mod_1260180753479_21.doc@ 46739@ @ 1
Pos: 12.1 1.1 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en/Si cher h eits - und s onst ige Hinweise/Achtung/Achtung:Defekteoder beschädigteGeräteaustauschen!@ 6\mod_1260180857358_21.doc @ 46743@ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 12.1 1.2 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en /Sic her h eits- un ds onsti ge Hin weise /Acht ung/Ac htung : Gerä te vor kri eche nden un di soli erend en Stof fen sch ütze n! @ 6\mod_1260181036216_21.doc@ 46747@ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 12.1 1.3 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en/Si cher h eits - und s onst ige Hin weis e/Ac ht ung /Acht ung : R eini gu ng n ur mit zul äss ige n M ater iali en! @ 6\mod_1260181203293_21.doc@ 46751@ @ 1
Cleaning only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 12.1 1.4 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en/Si cher h eits - und so nstige H inwei se/Ac htung /Acht ung: K ein Ko ntakts pray ver wend en! @ 6\mod_1260181290808_21.doc @ 46755@ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 12.1 1.5 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en/Si c her hei ts- und s onstig e Hinwei se/Ac htung /Acht ung: Verp olung ver meide n! @ 6\mod_1260184045744_21.doc@ 46767@ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 12.1 1.6 / All e S erie n (Al lge mei ne M o dule) /Wi cht ige Erläu ter ung en/Si cher h eits - und s ons tig e H in wei se/A cht u ng/Ac ht ung: El ektr ost atis ch e E ntl adu ng verm eid en! @ 6\mod_1260181364729_21.doc@46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that you may destroy by
electrostatic discharge when you touch. Pay attention while handling the devices
to good grounding of the environment (persons, job and packing).
Pos: 13 /D oku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810@ @ 1

12 Quickstart Description WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 14 /A lle Ser ien (Al lge meine Mo dule)/ Übers chrif ten für alle S erien /Sch nells tartb eschrei bung - Ü bersc hrift 1 @ 9\mod_1287492268613_21.doc@ 65713 @ 1@ 1
3 Quickstart Description
Pos: 15 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /Ei nlei t ung /Fel d busk oppl er /-c ontr oller / Einl eit en der T ex t/Qui c kst art/ St arter Ki t 75 0-0880 :A ufbau d er Hard ware Ü2 u nd Einl eitu ng @ 13\mod_1348142899039_21.doc@ 103066@ 2 @ 1
3.1 Hardware Design
The fieldbus node is to be structured as follows (viewed from left to right):
Table 3: Fieldbus Node Structure
Position
I/O-Modul
1
PLC ETHERNET
750-880
2
Digital input module
750-400
3
Digital output module
750-501
4
End module
750-600
The 24VDC power supply unit is linked to the power (24V and 0V) for the
fieldbus controller and for the power jumper contacts (see No. 5 in the figures of
the PLC views and connections below).
For the application used in the example, it is sufficient to connect a jumper
between "24V" and "+" (see No. 6) or between "0V" and "-" (see No. 9).
Figure 1: View and 24V/0V connection of the ETHERNET-TCP/IP fieldbus controller
Pos: 16 /D oku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Quickstart Description 13
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 17 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht/ Fel db us koppl er /-co ntr oll er/ Leg end e/A nsic ht - Legendezur AnsichtSETHERNET(750-880,8 81,8 82) - Tabellenkopf undNr: 1 @ 7\mod_1266415064861_21.doc@ 50950@ @ 1
Table 4: Legend to the View ETHERNET TCP/IP Fieldbus Controller
No.
Designati
on
Meaning Details see Chapter:
1
LINK
ACT 1, 2,
MS, NS,
I/O, USR
Status LEDs Fieldbus "Device Description" >
"Display Elements"
Pos: 18 /S erie 7 50 (WA GO-I/O-SY STE M)/ Ger ät ebes c hrei bung /A nsic ht/ Fel db us koppl er /-co ntr oll er/ Leg end e/A nsic ht - L ege nde allg für K oppl er/Co ntrol ler Nr: 2-13 @ 4\mod_1238495560382_21.doc @ 29458@ @ 1
2 ---
Group marking carrier (retractable) with
additional marking possibility on two miniature
WSB markers
---
3 A, B or C Status LED’s System/Field Supply
"Device Description" >
"Display Elements"
4 --- Data Contacts
"Connect Devices" > "Data
Contacts/Internal Bus"
5 24 V, 0 V CAGE CLAMP® Connections System Supply
"Connect Devices" >
"Connecting a conductor to
the CAGE CLAMP
®
"
6 + CAGE CLAMP® Connections Field Supply DC
24 V
"Connect Devices" >
"Connecting a conductor to
the CAGE CLAMP
®
"
7 --- Power Jumper Contact 24 V DC
"Connect Devices" >
"Power Contacts/
Field Supply"
8 --- Unlocking Lug
"Assembly" >
"Inserting and Removing
Devices"
9 - CAGE CLAMP® Connections Field Supply 0 V
"Connect Devices" >
"Connecting a conductor to
the CAGE CLAMP
®
"
10 --- Power Jumper Contact 0 V
"Connect Devices" >
"Power Contacts/
Field Supply"
11 (Earth) CAGE CLAMP® Connections Field Supply
(Earth)
"Connect Devices" >
"Connecting a conductor to
the CAGE CLAMP
®
"
12 --- Power Jumper Contact (Earth)
"Connect Devices" >
"Power Contacts/
Field Supply"
13 --- Service Interface (open flap)
"Device Description" >
"Operating Elements"
Pos: 19 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht/ Fel db us koppl er /-co ntr oll er/ Leg end e/A nsic ht - L ege nde F el db usans chl uss 2 x R J-45 al s 2-Port-ET HER NET -Switc h Nr : 1 4 @ 7\mod_1266416127949_21.doc@ 50959 @ @ 1
14 X1, X2
Fieldbus connection 2 x RJ-45 as 2-Port
ETHERNET Switch
"Device Description" >
"Connectors"
Pos: 20 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht/ Fel db us koppl er /-co ntr oll er/ Leg end e/A nsic ht - L eg end e für S peic her kart en-St ec kplat z Nr : 1 5 @ 9\mod_1286270217424_21.doc@ 65383@ @ 1
15 --- SD card slot with cover lid
„Device Description“ >
„Operating Elements“
Pos: 21 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht/ Fel db us koppl er /-co ntr oll er/ Leg end e/A nsic ht - L egend e für Ver rieg elungs schei be Nr: 16 @ 9 \mod_1286271263513_21.doc@ 65386@ @ 1
16 --- Locking Disc "Assembly" > "Inserting
and Removing Devices"
Pos: 22 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht/ Fel db us koppl er /-co ntr oll er/ Leg end e/A nsic ht - L egend e für Adr essw ahls chal ter Nr: 17 @ 9 \mod_1296638222313_21.doc@ 69118@ @ 1
17 --- Address Selection Switch
"Device Description" >
"Operating Elements"
Pos: 23 /D oku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810@ @ 1

14 Quickstart Description WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 24 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /Ei nlei t ung /Fel d busk oppl er /-c ontroll er/Ei nlei tend er Text /Quic kst art 750-0 88x: Hi nwei s: Betri ebsart ensc halter i n die ober e Stel lung sc halt en! @ 9\mod_1287492632163_21.doc@ 65716 @ @ 1
Set the operating mode switch to the top position!
Set the operating mode switch to the top position. At this setting, the firmware
and application program are executed (Activate program execution / "RUN").
The mode selector switch is located behind the cover flap (see No. 13 in the
Figure above).
Figure 2: Mode selector switch (closed and open damper of the service port)
Table 5: Mode selector switch
Number
Description
1
Open the damper
2
Operating mode switch
Pos: 25 /D oku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Quickstart Description 15
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 26 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /Ei nlei t ung /Fel d busk oppl er /-c ontr oller / Einl eit en der T ex t/Qui c kst art/ St arter Ki t 75 0-0880:Speicherkarte@ 13\mod_1348217984343_21.doc@ 103159@ @ 1
Only use recommended memory cards!
Only use the SD memory card available from WAGO (Item No. 758-879/000001)
because it is specified for industrial applications under harsh environmental
conditions and for use in the fieldbus controller.
Compatibility with other commercially available storage media cannot be
guaranteed!
Figure 3: (1) Open the memory card slot, (2) insert the SD card
Pos:27/Dokumentationallgemein/Glieder ung sel em ent e/---Sei te nwec hsel ---@ 3\mod_1221108045078_0.doc@ 21810@ @ 1

16 Quickstart Description WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
Pos: 28 /A lle Ser ien (Al lge meine Mo dule)/ Übers chrif ten für alle S erien /Inbet rieb nehm en -K o nfig urier en - Para met rier en /V orb erei te nde M aß na hm en - Üb ersc hrift 2 @ 13\mod_1348215195986_21.doc@ 103153@ 2 @ 1
3.2 Preparatory Measures
Pos: 29 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /Ei nlei t ung /Fel d busk oppl er /-c ontr oller / Einl eit en der T ex t/Qui c kst art/ St arter Ki t 75 0-0 88x: Do kument ation u nd Beis piel proje kte her unterl aden @ 1 3\mod_1348215563298_21.doc@ 103156@ 3 @ 1
3.2.1 Download documentation and sample projects
Download documentation and sample projects!
Extensive documentation and sample projects for this Starterkit are available at
the WAGO homepage. You will find these at www.wago.com/startkits.
Figure 4: Download possibilities at the WAGO homepage
Pos: 30 /A lle Ser ien (Al lge meine Mo dule)/ Übers chrif ten für alle S erien /Inbet rieb nehm en -K o nfig urier en - Para met rier en / WAGO-I /O-PR O i nst alli eren - Ü b ersc hrif t 3 @ 13\mod_1348225656942_21.doc@ 103166@ 3@ 1
3.2.2 Installing WAGO-I/O-PRO
Pos: 31 /S erie 7 50 (WA GO-I/O-SYST EM )/ Ger ät ebes chr ei bung /Ei nlei tu ng /Fel d busk oppl er /-con tr oller /E inl eit end er T ext /Qui c kst art/ St arter Ki t 75 0-08 8 x: Li efer u mfang @ 13 \mod_1348225844857_21.doc @ 103189 @ @ 1
The Starterkit ETHERNET 750-880 includes a CD with the development
topology WAGO-I/O-PRO. This CD is also available individually under item
number 759-333.
Pos: 32 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /Ei nlei t ung /Fel d busk oppl er /-c ontr oller / Einl eit en der T ex t/Qui c kst art/ St arter kit 75 0-088 0: Besc hreibu ng - Teil 1 @ 13\mod_1350631197488_21.doc@ 104920@ 34443 @ 1
WAGO-I/O-PRO is a programming and visualization tool for control programs.
This software is used to develop PLC applications for WAGO I/O SYSTEM 750
programmable fieldbus controllers. WAGO-I/O-PRO runs in compliance with the

WAGO-I/O-SYSTEM 750 Quickstart Description 17
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
IEC 61131-3 standard, which specifies the requirements for a programming
system.
You can use this programming tool to develop application programs in the
programming languages AWL, KOP, FUP, CFC, ST and AS.
Proceed as follows to perform the installation:
1. Insert the WAGO-I/O-PRO CD into your CD-ROM drive.
2. If the installation does not begin automatically, start the file Setup.exe.
Figure 5: Contents of the WAGO-I/O-PRO CD (folder view), Setup.exe file
3. Select the language. Then confirm this selection by clicking [OK].
Figure 6: Selecting the setup language

18 Quickstart Description WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
4. Click the [Next] button in order to start setup using the "InstallShield
Wizard".
Figure 7: Starting the setup
5. Click on the [OK] button in order to accept the license agreement.
Figure 8: License agreement

WAGO-I/O-SYSTEM 750 Quickstart Description 19
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
6. Select the target directory. Then confirm this selection by clicking [Next].
Figure 9: Selecting the target directory
7. Select the components to be installed. Then confirm this selection by
clicking [Next].
Figure 10: Selection of components

20 Quickstart Description WAGO-I/O-SYSTEM 750
750-880 ETHERNET Programmable Fieldbus
Quickstart Reference
Version 1.0.0
8. Select the program folder. Then confirm this selection by clicking [Next].
Figure 11: Selection of program folder
9. Check the settings you have defined. Then confirm this selection by clicking
[Next].
Figure 12: Overview of configuration