M-system R30NCIE1 User manual

MODEL: R30NCIE1
R30NCIE1 SPECIFICATIONS ES-9020 Rev.6 Page 1/7
https://www.m-system.co.jp/
Remote I/O R30 Series
NETWORK MODULE
(CC-Link IE Field network)
Functions & Features
• Interchanges analog or discrete I/O signals with the
filedbus (CC-Link IE Field network)
• Combined with R3 Series I/O modules
98 [3.86]
110
[4.33]
25
[.98]
mm [inch]
MODEL: R30NCIE1[1]
ORDERING INFORMATION
• Code number: R30NCIE1[1]
Specify a code from below for [1].
(e.g. R30NCIE1/Q)
• Specify the specification for option code /Q
(e.g. /C01)
[1] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
CAUTION
• The internal bus communication period for R3 series I/O
modules installed on the R30EBS is as follows.
Internal bus communication period = 6 msec. × number of
I/O module + 10 msec. (Data update period of main CPU)
Example: Four R3 I/O modules
6 msec. × 4 + 10 msec. = 34 msec.
Even when the R30EBS is mounted to the R30BS, the
internal bus communication period of R30 series is kept to
approx. 1 msec.
RELATED PRODUCTS
• PC configurator software (model: R30CFG)
• PC configurator software (model: R3CON)
Downloadable at M-System’s web site.
For connecting to PC, use commercially available Mini-B
type USB cable. (provided by user)
• R3 series I/O modules (except R3-TC2 and R3S-CM2A)
GENERAL SPECIFICATIONS
Connection
CC-Link IE Field: RJ-45 connector
Internal bus: Via the Installation Base (model: R30BS)
Internal power: Via the Installation Base (model: R30BS)
Isolation: CC-Link IE Field to internal bus or internal power
Input type & range:
R30 series I/O module: PC configuration software (model:
R30CFG)
R3 series I/O module: PC configuration software (model:
R3CON)
Network address: PC configuration software (model:
R30CFG)
Internal bus communication cycle: Approx. 1 msec.
Status indicator: RUN, RD, SD, D LINK, ERR, L ER, LINK
(Refer to the instruction manual.)
CC-Link IE Field COMMUNICATION
Protocol: IEEE 802.3
Transmission type: 1000BASE-T
Communication speed: 1 Gbps
Network cable: Cable conformed to CC-Link IE Field
Double shielded twist pair cable (CAT5e)
RJ-45 connector
Network topology: Line, star and ring
Max. number stations: 120 (Total slave station)
(Number of max. connectable slaves may vary depending
on the master module. Refer to the instruction manual of
the master module)
Max. station-to-station distance: 100 m
Station type: Remote device station
Link device: RX/RY 128 points, RWw/RWr 64 points

MODEL: R30NCIE1
R30NCIE1 SPECIFICATIONS ES-9020 Rev.6 Page 2/7
https://www.m-system.co.jp/
(Number of points summation of I/O module for R30 series
and R3 series)
NetWork No.: 1 to 239 (factory default: 1)
INSTALLATION
Current consumption: 160 mA
Operating temperature: -10 to +55°C (14 to 131°F)
Storage temperature: -20 to +65°C (-4 to +149°F)
Operating humidity: 10 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R30BS)
Weight: 125 g (0.28 lb)
PERFORMANCE
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute (CC-Link IE Field
to internal bus or internal power)
1500 V AC @ 1 minute (power input to FE; isolated on the
power supply module)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EXTERNAL VIEW
CN1
CN2
10
1
STATION No.
CONFIG
L ERLINKL ERLINK
RUN
RD
SD
D LINK
ERR
NCIE1
■FRONT VIEW
■BOTTOM VIEW
■SIDE VIEW
Status Indicator LEDs
PC Configurator Connector
CC-Link IE Field Communication
RJ-45 Modular Jack
Station No. Rotary SW
Lock Tab
Base Fixing Screw
Positioning Guide
Specifications

MODEL: R30NCIE1
R30NCIE1 SPECIFICATIONS ES-9020 Rev.6 Page 3/7
https://www.m-system.co.jp/
TRANSMISSION DATA DESCRIPTIONS
This unit recognize type of I/O module (number of occupied station) configured the same base, and assign it to I/O Modules
data with slot order automatically. However, I/O module assignment is performed only when power is turned on, in the case of
changing configuration of I/O module, please turn on power again.
Keep number of station occupied of I/O module under 64, because max number of occupied station is 64 per a node. When the
I/O module has space, data is transmitted close to HOST PC/PLC.
Station type: Remote device station
Link device: RX/RY 128points, RWw/RWr 64points
(Points are total of R30 series and R3series module)
E.g. I/O data is assigned as shown below in the case of following configuration.
BASE SLOT NO. MODEL REQUIRED NODES
R30BS08 PWR R30PS1 –
COM R30NCIE1 –
1 R30SV4 4
2 R30US2 2
3 R30TS4 4
4 R30YV4 4
5 R30XN16A 1
6 R30XN16A 1
7 R30YN16A 1
8 R30YN16A 1
R30EBS04 1 R3-SV8 8
2 R3-YV8 8
3 R3-DA32A 2
4 R3-DC32A 2
0 15
RWr n+0 Slot 1
+
2
+ 4
+ 6
+ 8
+ 10
+ 12
+ 14
Slot 2
Slot 3
Slot 4
■INPUT DATA
The figure below shows the data sent from the device to the master.
+
16
Slot 6
Slot 5
Slot 7
Slot 8
R30SV4
R30YN16A
R30YN16A
R30XN16A
R30XN16A
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH1
CH2
R30TS4
R30US2
R30YV4
+ 18
+ 36
+ 34
+ 32
+ 30
+ 28
+ 26
+ 24
+ 22
+ 20
0 15
RWw n+0 Slot 1
+
2
+ 4
+ 6
+ 8
+ 10
+ 12
+ 14
Slot 2
Slot 3
Slot 4
+
16
Slot 6
Slot 5
Slot 7
Slot 8
R30SV4
R30YN16A
R30YN16A
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH1
CH2
R30XN16A
R30XN16A
■OUTPUT DATA
The figure below shows the data received from the master.
R30TS4
R30US2
R30YV4
+ 18
+ 36
+ 34
+ 32
+ 30
+ 28
+ 26
+ 24
+ 22
+ 20
R30BS08
R30EBS04 Slot 1
Slot 2
Slot 3
Slot 4
Slot 1
Slot 2
Slot 3
Slot 4
R30BS08
R30EBS04
R3-YV8
R3-SV8
R3-DC32A
R3-DA32A
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH5
CH6
CH7
CH8
Di16 points
Di16 points
Do16 points
Do16 points
Di16 points
Di16 points
Do16 points
Do16 points
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH5
CH6
CH7
CH8
Di16 points
Di16 points
Do16 points
Do16 points
Di16 points
Di16 points
Do16 points
Do16 points
R3-YV8
R3-SV8
R3-DC32A
R3-DA32A

MODEL: R30NCIE1
R30NCIE1 SPECIFICATIONS ES-9020 Rev.6 Page 4/7
https://www.m-system.co.jp/
0
0
RX(n+0)
Remote READY
Module Status (R30 Series)
Module Status (R3 Series)
Error Status (R30 Series)
Data Error Status (R30 Series)
Error Status (R3 Series)
Data Error Status (R3 Series)
15
2 1 A B C D E 3 F 9 8 7 6 5 4
RX(n+3)
RX(n+4)
RX(n+5)
RX(n+6)
RX(n+2)
RX(n+1)
RX(n+7) Unused
• RX(n+0)0 to 7 is reservation area, RX(n+0) is used as Ready signal, the bit is “1” when this module is in normal.
RX(n+0)8 to A, RX(n+0)C to F are not used.
• Module Status
RX(n+1)0 to RX(n+1)F indicate whether individual I/O modules of R30 series are mounted or not .
RX(n+2)0 to RX(n+2)F indicate whether individual I/O modules of R3 series are mounted or not.
The bit corresponding to the mounted slot turns to “1”, and the unmounted slot to “0”
• Error Status
RX(n+3)0 to RX(n+3)F indicate error status for each module of R30 series.
The bit corresponding to such module turns to “1”, as described below.
When the each module is detached, the error bit is cleared.
However, when the last module is detached, the error bit is held.
R30X16(under development) input power in error or disconnected.
R30Y16(under development) output current in error (e.g. load unconnected)
RX(n+4)0 to RX(n+4)F indicate error status for each module of R3 series.
The bit corresponding to such module turns to “1”, as described below.
When the each module is detached, the error bit is held.
R3-TSx, R3-RSx, R3-US4 Input burnout.
R3-DA16A input power in error or disconnected
R3-YSx output current error (e.g load unconnected)
R3-PC16A external power supply in error or disconnected
• Data Error Status
RX(n+5)0 to RX(n+5)F indicate data error status for each module of R30 series.
The bit corresponding to such module turns to “1”, as described below.
When the each module is detached, the error bit is cleared.
However, when the last module is detached, the error bit is held.
Input value is out of -15% to +115%
R30TS4, R30RS4, R30USx Input burnout.
RX(n+6)0 to RX(n+6)F indicate error status for each module of R3 series.
The bit corresponding to such module turns to “1”, as described below.
When the each module is detached, the error bit is held.
Input value is out of -15% to +115%
In the case of R3-US4 (voltage input) input level out of -10% to +110%.
RX(n+1)0, RX(n+3)0, RX(n+5)0 R30 series slot 1
RX(n+1)1, RX(n+3)1, RX(n+5)1 R30 series slot 2
RX(n+1)2, RX(n+3)2, RX(n+5)2 R30 series slot 3
:
RX(n+1)F, RX(n+3)F RX(n+5)F R30 series slot 16
RX(n+2)0, RX(n+4)0, RX(n+6)0 R3 series extension slot 1
RX(n+2)1, RX(n+4)1, RX(n+6)1 R3 series extension slot 2
RX(n+2)2, RX(n+4)2, RX(n+6)2 R3 series extension slot 3
:
RX(n+2)F, RX(n+4)F, RX(n+6)F R3 series extension slot 16
Link devices other than the above are not in use.

MODEL: R30NCIE1
R30NCIE1 SPECIFICATIONS ES-9020 Rev.6 Page 5/7
https://www.m-system.co.jp/
MODULE STATUS, ERROR STATUS, DATA ERROR STATUS
0 15
Module 1
Module 2
Module 3
:
Module 16
Shows each module's availability and error status.
I/O DATA DESCRIPTIONS
■OPERATION IN CASE OF A COMMUNICATION ERROR WITH I/O MODULES
When the communication between the network module and the I/O modules is lost due to an error in an input module, the last
process values are held until the communication is re-established.
■ ANALOG DATA (16-bit data, models: R30SV4, R30SV2, R30YV4, R30YS4, R30US4, etc.)
0 15
16-bit binary data.
Basically, 0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).
Negative percentage is represented in 2's complements.
■ ANALOG DATA (16-bit data, models: R30RS4, R30TS4, R30US4, etc.)
0 15
16-bit binary data.
With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.
With °F temperature unit, the integer section of raw data is directly converted into the data.
For example, 135.4°F is converted into 135.
Minus temperature is converted into negative values, represented in 2’s complements.
■ ANALOG DATA (16-bit data, models: R30CT4E etc.)
0 15
16-bit binary data.
Integer obtained by multiplying unit value (A) by 100.
In case of CLSE-R5, integer obtained by multiplying unit value (A) by 1000.
■ ANALOG DATA (32-bit data, models: R3-PA2, PA4A, WT1, WT4, etc.)
0 15
+0
0 15
Higher 16 bits+1
32-bit binary data is used for accumulated counts, encoder positions and active energy.
Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.
Lower 16 bits

MODEL: R30NCIE1
R30NCIE1 SPECIFICATIONS ES-9020 Rev.6 Page 6/7
https://www.m-system.co.jp/
■ ANALOG DATA (32-bit data, models: R3-BA32A, BC32A, etc.)
32-bit binary data is used for BCD.
Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.
0 15
+0 Lower 16 bits
0 15
+1
Higher 16 bits
■ 16-POINT DISCRETE DATA (models: R30XN16A, R30YN16x, etc.)
0 15
Input 1 (Output 1)
Input 2 (Output 2)
Input 3 (Output 3)
: :
Input 16 (Output 16)
0 : OFF
1 : ON
EXTERNAL DIMENSIONS unit: mm [inch]
110 [4.33]
25 [.98] 98 [3.86]

MODEL: R30NCIE1
R30NCIE1 SPECIFICATIONS ES-9020 Rev.6 Page 7/7
https://www.m-system.co.jp/
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
CC-Link IE Field CN1
CC-Link IE Field CN2
Regarding CN1 and CN2 of RJ-45 connector for CC-Link IE Field network, there is no restriction for connection order.
INTERNAL BUS
INTERNAL POWER
RJ-45 MODULAR JACK
RJ-45 MODULAR JACK
USB CONNECTOR
PC CONFIGURATOR
CONNECTOR
Control
Circuit
Isolation
Isolation
STATUS
IND. LED
STATION NO. SETTING
ROTARY SW
Comm.
Circuit
BUS CONNECTOR
Specifications are subject to change without notice.