Siemens SIMATIC ET 200SP User manual

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
ET 200SP
Digital input module
DI 4x120..230VAC ST
(6ES7131-6FD01-0BB1)
Manual
09/2017
A5E32043398
-AC
Preface
Guide to documentation
1
Product overview
2
Wiring
3
Parameters/address space
4
Interrupts/diagnostics alarms
5
Technical specifications
6
Parameter data record
A

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32043398-AC
Ⓟ
10/2017 Subject to change
Copyright © Siemens AG 2014 - 2017.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
4Manual, 09/2017, A5E32043398-AC
Preface
Purpose of the documentation
This manual supplements the system manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
Functions that generally relate to the system are described in this manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the system.
Changes compared to previous version
Compared to the previous version, this manual contains the following change:
Due to the change in hardware, the article number of the module has been changed from
6ES7131-6FD00-0BB1 to 6ES7131-6FD0
1
-0BB1. Both modules are compatible, except for
the firmware-update function.
Conventions
CPU: When the term "CPU" is used in this manual, it applies to the CPUs of the S7-1500
automation system as well as to the CPUs/interface modules of the distributed I/O system
ET 200SP.
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.

Preface
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
Manual, 09/2017, A5E32043398-AC 5
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens' products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit (http://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under (http://www.siemens.com/industrialsecurity).

Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
6Manual, 09/2017, A5E32043398-AC
Table of contents
Preface ................................................................................................................................................... 4
1 Guide to documentation .......................................................................................................................... 7
2 Product overview .................................................................................................................................. 12
2.1 Properties............................................................................................................................... 12
3 Wiring ................................................................................................................................................... 14
3.1 Wiring and block diagram ...................................................................................................... 14
4 Parameters/address space ................................................................................................................... 17
4.1 Parameters............................................................................................................................. 17
4.2 Explanation of parameters ..................................................................................................... 17
4.3 Address space ....................................................................................................................... 18
5 Interrupts/diagnostics alarms................................................................................................................. 19
5.1 Status and fault displays ........................................................................................................ 19
5.2 Diagnostics alarms................................................................................................................. 21
5.3 Load voltage status ................................................................................................................ 21
6 Technical specifications ........................................................................................................................ 22
6.1 Technical specifications ......................................................................................................... 22
A Parameter data record .......................................................................................................................... 26
A.1 Parameter assignment and structure of parameter data record............................................ 26

Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
Manual, 09/2017, A5E32043398-AC 7
Guide to documentation
1
The documentation for the SIMATIC S7-1500 automation system and the SIMATIC
ET 200MP distributed I/O system is arranged into three areas.
This arrangement enables you to access the specific content you require.
Basic information
The System Manual and Getting Started describe in detail the configuration, installation,
wiring and commissioning of the SIMATIC S7-1500 and ET 200MP systems. The STEP 7
online help supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.

Guide to documentation
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
8Manual, 09/2017, A5E32043398-AC
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
S7-1500 and ET 200MP systems, e.g. diagnostics, communication, motion control, Web
server, OPC UA.
You can download the documentation free of charge from the Internet
(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-
overview/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.
You can download the product information free of charge from the Internet
(https://support.industry.siemens.com/cs/us/en/view/68052815).
Manual Collection S7-1500/ET 200MP
The Manual Collection contains the complete documentation on the SIMATIC S7-1500
automation system and the ET 200MP distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/86140384).
SIMATIC S7-1500 comparison list for programming languages
The comparison list contains an overview of which instructions and functions you can use for
which controller families.
You can find the comparison list on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/86630375).
"mySupport"
With "mySupport", your personal workspace, you make the best out of your Industry Online
Support.
In "mySupport", you can save filters, favorites and tags, request CAx data and compile your
personal library in the Documentation area. In addition, your data is already filled out in
support requests and you can get an overview of your current requests at any time.
You must register once to use the full functionality of "mySupport".
You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en).
"mySupport" - Documentation
In the Documentation area in "mySupport" you can combine entire manuals or only parts of
these to your own manual.
You can export the manual as PDF file or in a format that can be edited later.
You can find "mySupport" - Documentation on the Internet
(http://support.industry.siemens.com/My/ww/en/documentation).

Guide to documentation
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
Manual, 09/2017, A5E32043398-AC 9
"mySupport" - CAx data
In the CAx data area in "mySupport", you can access the current product data for your CAx
or CAe system.
You configure your own download package with a few clicks.
In doing so you can select:
●Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
●Manuals, characteristics, operating manuals, certificates
●Product master data
You can find "mySupport" - CAx data on the Internet
(http://support.industry.siemens.com/my/ww/en/CAxOnline).
Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus on individual products.
You will find the application examples on the Internet
(https://support.industry.siemens.com/sc/ww/en/sc/2054).
TIA Selection Tool
With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).

Guide to documentation
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
10 Manual, 09/2017, A5E32043398-AC
SIMATIC Automation Tool
You can use the SIMATIC Automation Tool to perform commissioning and maintenance
activities simultaneously on various SIMATIC S7 stations as a bulk operation independent of
the TIA Portal.
General function overview:
●Network browsing and creation of a table showing the accessible devices in the network.
●Flashing of device LEDs or HMI display to locate a device
●Downloading of addresses (IP, subnet, gateway) to a device
●Downloading the PROFINET name (station name) to a device
●Placing a CPU in RUN or STOP mode
●Setting the time in a CPU to the current time of your PG/PC
●Downloading a new program to a CPU or an HMI device
●Downloading from CPU, downloading to CPU or deleting recipe data from a CPU
●Downloading from CPU or deleting data log data from a CPU
●Backup/restore of data from/to a backup file for CPUs and HMI devices
●Downloading service data from a CPU
●Reading the diagnostics buffer of a CPU
●Performing a CPU memory reset
●Resetting devices to factory settings
●Downloading a firmware update to a device
You can find the SIMATIC Automation Tool on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/98161300).
PRONETA
With SIEMENS PRONETA (PROFINET network analysis), you analyze the PROFINET
network during commissioning. PRONETA features two core functions:
●The topology overview independently scans PROFINET network and all connected
components.
●The IO check is a fast test of the wiring and the module configuration of a system.
You can find SIEMENS PRONETA on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/67460624).

Guide to documentation
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
Manual, 09/2017, A5E32043398-AC 11
SINETPLAN
SINETPLAN, the Siemens Network Planner, supports you in planning automation systems
and networks based on PROFINET. The tool facilitates professional and predictive
dimensioning of your PROFINET installation as early as in the planning stage. In addition,
SINETPLAN supports you during network optimization and helps you to exploit network
resources optimally and to plan reserves. This helps to prevent problems in commissioning
or failures during productive operation even in advance of a planned operation. This
increases the availability of the production plant and helps improve operational safety.
The advantages at a glance
●Network optimization thanks to port-specific calculation of the network load
●Increased production availability thanks to online scan and verification of existing systems
●Transparency before commissioning through importing and simulation of existing STEP 7
projects
●Efficiency through securing existing investments in the long term and optimal exploitation
of resources
You can find SINETPLAN on the Internet (https://www.siemens.com/sinetplan).

Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
12 Manual, 09/2017, A5E32043398-AC
Product overview
2
2.1
Properties
Order number
6ES7131-6FD01-0BB1
View of the module
①
Module type and name
⑦
Function class
②
LED for diagnostics
⑧
Color coding module type
③
2D matrix code
⑨
Function and firmware version
④
Wiring diagram
⑩
Color code for selecting the color identification labels
⑤
LEDs for channel status
⑪
BU type
⑥
LED for supply voltage
⑫
Article number
Figure 2-1 View of the module DI 4x120..230VAC ST

Product overview
2.1 Properties
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
Manual, 09/2017, A5E32043398-AC 13
Properties
The module has the following technical properties:
●4 digital inputs
●Supply voltage L+
●Suitable for connection of switches and 2-wire sensors in accordance with IEC 61131,
type 3
The module supports the following functions:
Table 2- 1 Version dependencies of the functions
Function
HW version
FW ver-
sion
STEP 7
GSD file
TIA Portal
V5.x
PROFINET IO
PROFIBUS DP
Identification data
I&M0 to I&M3
FS01 V0.0.0
and
higher
V14 or higher
with
HSP 0222
V5.5 SP3 or higher
with HSP 0229 V7.0
X X
Configuration in RUN FS01 V0.0.0
and
higher
V14 or higher
with
HSP 0222
V5.5 SP3 or higher
with HSP 0229 V7.0
X X
Value status FS01 V0.0.0
and
higher
V14 or higher
with
HSP 0222
V5.5 SP3 or higher
with HSP 0229 V7.0
X X
Accessories
The following accessories must be ordered separately:
●Labeling strips
●Color identification labels
●Reference identification label
●Shield connector
See also
You can find additional information on the accessories in the ET 200SP Distributed I/O
System (http://support.automation.siemens.com/WW/view/en/58649293) system manual.

Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
14 Manual, 09/2017, A5E32043398-AC
Wiring
3
3.1
Wiring and block diagram
This section includes the block diagram of the DI 4x120..230VAC ST module with the
terminal assignments for a 2-wire, 3-wire and 4-wire connection.
Information about wiring of the BaseUnit is available in the system manual ET 200SP
distributed I/O system (http://support.automation.siemens.com/WW/view/en/58649293).
Note
You may use and combine the different wiring options for all chan
nels.
NOTICE
Hazardous voltage, risk of fatal or serious injury
Always disconnect the system and module from the power supply before commencing
work.
Note
Limiting overvoltage
You must ensure overvoltage is limited to 1
kV for the encoder supply.
Note
Power limitation
To limit power, each input voltage must have a fuse with a maximum rating of 10
A tripping
current. The fuse must be a quick
-acting microfuse.

Wiring
3.1 Wiring and block diagram
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
Manual, 09/2017, A5E32043398-AC 15
Connection: 2-wire and 3-wire connection
The following figure shows the block diagram and an example of the terminal assignment of
the digital input module DI 4x120..230VAC ST on the BaseUnit BU type B1 without
AUX terminals (2-wire and 3-wire connection).
①
2-wire connection
DIn
Input signal, channel n
②
3-wire connection
L1
Encoder supply, channel n
③
Backplane bus interface
1L / 2L
Infeed 120 ... 230 V AC
④
Input electronics
1N / 2N
N-conductor connection
⑤
Color identification label CCxx (optional)
DIAG
Error or Diagnostics LED (green, red)
P1, P2, AUX Internal self-assembling voltage buses
Connection to left (dark-colored BaseUnit)
Connection to left interrupted (light-colored
BaseUnit)
PWR Power LED (green)
.0 to .3
Channel status LED (green)
Figure 3-1 Wiring and block diagram for 1-wire and 2-wire connection of encoders

Wiring
3.1 Wiring and block diagram
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
16 Manual, 09/2017, A5E32043398-AC
Connection: 4-wire connection:
The following figure shows the block diagram and an example of the terminal assignment of
the digital input DI 4x120..230VAC ST on the BaseUnit BU type B1 with AUX terminals
(4-wire connection).
①
4-wire connection
DIn
Input signal, channel n
②
Backplane bus interface
L1
Encoder supply, channel n
③
Input electronics
1L / 2L
Infeed 120 ... 230 V AC
④
Color identification label CCxx (optional)
1N / 2N
N-conductor connection
P1, P2, AUX Internal self-assembling voltage buses
Connection to left (dark-colored BaseUnit)
Connection to left interrupted (light-colored
BaseUnit)
DIAG Error or diagnostics LED (green, red)
.0 to .3
Channel status LED (green)
PWR
Power LED (green)
Figure 3-2 Wiring and block diagram for 4-wire connection of encoders.

Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
Manual, 09/2017, A5E32043398-AC 17
Parameters/address space
4
4.1
Parameters
Parameters of the DI 4x120..230VAC ST
Specify the module properties with the various parameters in the course of your STEP 7
configuration. The following table lists the configurable parameters. The effective range of
the configurable parameters depends on the type of configuration.
The following configurations are possible:
●Central operation with an ET 200SP CPU
●Distributed operation on PROFINET IO in an ET 200SP system
●Distributed operation with PROFIBUS DP in an ET 200SP system
When performing the configuration in the user program, use the "WRREC" instruction to
transfer the parameters to the module using data records (refer to the section Parameter
assignment and structure of parameter data record (Page 26)).
The following parameter settings are possible:
Table 4- 1 Configurable parameters and their defaults (GSD file)
Parameters
Value range
Default
Configuration in
RUN
Scope with configuration software,
e.g. STEP 7 (TIA Portal)
GSD file
PROFINET IO
GSD file
PROFIBUS DP
Channel activated •Disable
•Enable
Enable Yes Channel Channel
4.2
Explanation of parameters
Channel activated
Determines whether a channel is enabled or disabled.

Parameters/address space
4.3 Address space
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
18 Manual, 09/2017, A5E32043398-AC
4.3
Address space
The module can be configured differently in STEP 7; see following table. Depending on the
configuration, additional/different addresses are assigned in the process image of the inputs.
Configuration options of DI 4x120..230VAC ST
You can configure the module with STEP 7 (TIA Portal) or with a GSD file. If you configure
the module using a GSD file, the configurations are available under various short
designations/module names; see the table below. The following configurations are possible:
Table 4- 2 Configuration options with GSD file
Configuration
Short designation/module
name in the GSD file
Configuration software, e.g. with STEP 7 (TIA Portal)
Integrated in
hardware catalog
STEP 7
GSD file
PROFINET IO
GSD file
PROFIBUS DP
1 x 4-channel without value
status
DI 4x120..230VAC ST V0.0 V14, SP1 or high-
er with HSP 0222
X X
1 x 4-channel with value status DI 4x120..230VAC ST
V0.0, QI
V14, SP1 or high-
er with HSP 0222
X ---
Evaluating the value status
An additional two bytes are allocated in the input address space if you enable the value
status for the digital module. Bits 0 to 3 in these bytes are assigned to a channel. They
provide information about the validity of the digital value.
Bit = 1: No fault is present on the channel.
Bit = 0: Channel is disabled or there is a fault/error on the module.
If a fault/error occurs on a channel with this module, the value status for all channels is 0.
Address space of the digital input module DI 4x120..230VAC ST
The following figure shows the assignment of the address space for the
DI 4x120..230VAC ST with value status (Quality Information (QI)). The addresses for the
value status are only available if the value status is enabled.
Figure 4-1 Address space of the DI 4x120..230VAC ST digital input module with value status
Note
Value status
The value status is independent of the connected supply voltage 120 ... 230
V AC.

Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
19 Manual, 09/2017, A5E32043398-AC
Interrupts/diagnostics alarms
5
5.1
Status and fault displays
LED displays
The figure below shows the LED displays (status and fault displays) of the
DI 4x120..230VAC ST.
①
DIAG (green/red)
②
Channel status (green)
③
PWR (green)
Figure 5-1 LED display

Interrupts/diagnostics alarms
5.1 Status and fault displays
Digital input module DI 4x120..230VAC ST (6ES7131-6FD01-0BB1)
20 Manual, 09/2017, A5E32043398-AC
Meaning of the LEDs
The tables below explain the meaning of the Status and fault displays.
LED DIAG
Table 5- 1 LED DIAG fault display
LED DIAG
Meaning
Off
Backplane bus supply of the ET 200SP not OK
Flashing
Module parameters not assigned
On
Module parameters assigned
Flashing
Module diagnostics is available
LED channel status
Table 5- 2 Channel status LED status and fault display
LED channel
status
Meaning
Off
Process signal = 0
On
Process signal = 1
LED PWR
Table 5- 3 LED PWR status display
LED PWR
Meaning
Off
Supply voltage L+ missing
On
Supply voltage L+ present