Macma MM2315 User manual

BELT SANDER
MODEL MM2315
OWNER’S MANUAL
PLEASE SAVE THIS MANUAL FOR FUTURE REFERENCE
1401

WARNING
For Your Own Safety Read instruction Manual Before Operating Sander.
1. Wear eye protection.
2. Support workpiece with backstop or workable.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning on.
3. KEEP WORKAREACLEAN. Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations or expose
them to rain. Keep work area well lighted.
5. KEEP CHILDRENAWAY.ALL visitors should be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
9. WEAR PROPER APPAREL. Wear no loose clothing, gloves, neckties, rings, bracelets, or other jewelry
which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to
contain long hair. Exception: The reference to gloves may be omitted from the instructions for a grinder.
10. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses, they are NOT safety glasses.
11. SECURE WORK. Use clamps or a vise to hold work when practical. It’s after than using your hand and it
frees both hands to operate tool.
12. DON’T OVERREACH. Keep proper footing and balance at all times.
13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
14. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and th
like.
15. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging
in.
16. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The
use of improper accessories may cause risk of injury to persons.
17. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function-check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions
that may affect its operation.A guard or other part that is damaged should be properly repaired or replaced.
19. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or
cutter only.
20. NEVER LEAVE TOOL RUNNING UNATTENDED TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
A. GROUNDING INSTRUCTIONS
1. All grounded, cord-connected tools: in the event of a malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an
electric cord having an equipment, grounding conductor and a grounding plug. The plug must be plugged
into a matching outlet that is properly installed and grounded in accordance with all local codes and

ordinances.
Do not modify the plug provided-if it will not fit the outlet, have the proper outlet installed by qualified
electrician. Improper connection of the equipment grounding conductor can result in a risk of electric shock.
The conductor with insulation having an outlet surface that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal
Check-with a qualified electrician or service personnel if the grounding instructions are not completely
understood. or if in doubts to whether the tool is properly grounded. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. Repair or replace damage
or worn cord immediately.
2. Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating less than 150
volts.
This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A in
Figure in Figure. The tool has a grounding plug that looks like the plug illustrated in Sketch A in Figure.
Atemporary adapter, which looks like the adapter illustrated in Sketches B and C, may be used to connect
this plug to a 2-pole receptacle as shown in Sketch B if a properly grounded is not available. The temporary
adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The
green-colored rigid ear, plug and the like extending from the adapter must be connected to a permanent
ground such as a properly grounded outlet box.
3. Grounded, cord-connected tools in tended for use on a supply circuit having a nominal rating between
150-250 volts, inclusive:
This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch D in
Figure. The tool has a grounding plug that looks like the plug illustrated in Sketch D in Figure.
Make sure the tool is connected to an outlet having the same configuration as the plug. No adapter is
available or should be used with this tool. If the tool must be reconnected for use on a different type of
electric circuit, the reconnection should be made by qualified service personnel; and after reconnection, the
tool should comply with all local code and ordinances.

NO.
DESCRIPTION
Q’TY
NO.
DESCRIPTION
Q’TY
1
Clamp
3
45
Thread column
2
2
Locating arm
1
46
Locking nut
1
3
Locating arm fixing plate
1
47
Screw M6X16
1
4
Extension support
1
48
Nylon washer
1
5
Extension platform
1
49
Clamp M20X1.5
3
6
Sliding block
4
50
KJD18(--) Switch
1
7
Belt cover
1
50A
KJD12 Switch box
1
8
Handle
8
51
Washer 9X28X3
1
9
Sanding belt 2515*152 60P
1
52
Motor roller
1
10
Handle
1
53
Motor washer
1
11
Belt replacing plate
1
54
Key 6X12
1
12
Handle
1
55
Base
1
13
Bracket
1
59
Big locking handle
1
14
Sanding belt platform
1
62
Nut
1
15
Tension bar
1
63
Stopping iron
1
16
Table
1
64
Pointer
1
Sticking graphite plate960X180X2
1
65
Sliding iron
1
17
Spring
1
66
Scale
1
18
Roller arm
1
67
Handle
1
19
Driver roller
1
67A
Big washer 6
4
20
Shaft
1
68
Bolt M6X25
3
21
Globular sleeve
1
68A
Bolt M6X12
1
22
Nut
1
69
Spring washer 6
14
23
Screw
1
70
Bolt M8X30
1
24
Driver wrench
1
71
Motor
1
25
Nut M12
1
72
Nut M6
1
26
Handle
2
73
Washer 6
22
27
Scale fixing plate
1
74
Shaft coupling
1
Scale
1
75
Elastomer
1
28
Washer
1
76
Screw M8X55
2
29
Spring
1
77
Ring 19
1
30
Upper guide bush
1
77A
Ring 42
2
31
Sliding shaft
1
78
Bearing 6004
2
32
Lower guide bush
1
79
Washer 8
1
33
Bearing bolt
1
80
Shaft coupling
1
34
Bearing 60/7
1
81
Washer 8
32
35
Nut M6
3
81A
Big washer 8
13
36
Bearing base
1
82
Bolt M8X35
8
37
Motor base
1
83
Bolt M8X45
1
38
Screw M8X35
5
84
Nut M8
22
39
Screw M6X20
8
84A
Locking nut M8
1
40
Pin
1
85
Nut M5
1
41
Fixing plate
1
85A
Locking washer 5
1
42
Fixing block
2
86
43
Nylon block
1
87
Washer 5
1
44
Up-and-down board
2
88
Screw M5X16
1
89
Pin 6X32
1
124
Cone-shaped gear I
1
90
Screw M8X25
4
125
Ring 80
1

90A
Screw M8X20
6
126
Bearing 6208
1
91
Spring washer8
30
127
Ring 40
1
92
Screw M6X10
2
128
Bearing base
1
93
Protection box
1
129
Bolt M8X30
6
94
Screw M6X10
3
130
Washer 8
12
95
Screw M4X20
3
132
Left iron
1
96
Screw M4X12
3
133
Right iron
1
96A
Locking washer 4
1
113
Washer 6
3
96B
switch box
1
114
Washer
1
97
Pin 3X6
1
115
Thread shaft
1
98
Nut M4
9
116
Bearing 6204
1
99
Nut M10
2
117
Pressing board
1
100
Washer 10
2
118
Pressing block
1
101
Screw
1
119
Handle
1
102
Spring
1
120
Bolt M6X110
3
103
Screw M6X6
1
121
Up-and-down base
1
104
Screw M4X16
3
122
Screw M8X10
2
105
Screw M8X25
4
123
Up-and-down shaft
1
106
Gear case
1
124
Cone-shaped gear I
1
107
Table
1
125
Ring80
1
108
Big washer 6
2
126
Bearing 6208
1
109
Bent board
2
127
Ring 40
1
110
Locking screw
1
128
Bearing base
1
111
Washer 10
1
129
Bolt M8X30
6
112
Collector
1
130
Washer 8
12
113
Locking washer 6
1
132
Left angle iron
1
114
Washer
1
133
Right angle iron
1
115
Shaft
1
134
Cone-shaped gear II
1
116
Bearing 6204
1
135
Ring 18
1
117
Pressing board
1
136
Turning shaft
1
118
Pressing block
1
137
Turning shaft base
1
119
Handle
1
138
Bush
1
120
Screw M6X110
3
139
Key 5X5X16
1
121
Up-and-down base
1
140
Handle
1
122
Screw M8X10
2
141
Big washer12
1
123
Up-and-down shaft
1
142
Nut M12
1
143
Locking nut M8
6
144
Shaft circle bush
1