Magic Chef RB15HA-1 User manual

I Refrigerator/Freezer_
.ofro. J
I1,,, I
w'-
Pleaseread the enclosed instructions to become better acquainted with your new model. In order to
prevent unnecessary service calls, refer to theself-service check list. If you do need service, be sure
to report the model and serial numbers to the service man. They are found on the serial plate, located
lit the upper front left corner of the lower liner. Here is a convenient place to record these numbers.
MODEL NO. SERIAL NO.

INSTALLATION A., U.L. listedrefrigeratorsandfreezersare ENERGY SAVER CONTROL
equipped with this type plug. During extremely humid weather, mois-
LOCATION SAFETY REMINDER ture has a tendencyto collect onobjectsthat
If possible, placeyour model out of direct If you are not going to useyour old refrige- are cooler than the surrounding air,just as
sunlightand away fromheat sourcessuch as rator, be sureto REMOVE THE DOORSso a droplets ofwater accumulate ona glass con-
a radiator, oven, or range, child won't be accidentally trapped insideraining an iced drink during a hot summer
and suffocate. This isrequired by law in day.This refrigerator is built to exacting
Your model should not be installed wheremany communities, standards a'nd, therefore,contains conden-
the temperaturewill go below 55°F. because satedriers that are designedto minimize any
it will notrunfrequently enough to maintain collectionof moistureonthe cabinet external
proper temperatures in the freezer. OPERATIONsurface during periods of high humidity.
Forease of installation,you shouldleave a -ENERGY SAVER
space of about one-half inch between your SAVES ,_=UCESE_T_,O=
refrigeratorand adjacentwalls or cabinets.If 81: I IING CONTIROLS .,,,;v4 awl_cH _MO ......
a wallprevents either door fromopening at Your new refrigerator has two controls.
least90°, movethe cabinetsidewaysan inch Onefor regulating the temperaturein the
or so to permit a 90Oopening so baskets and fresh food compartment and one for the If you liveinanareaoflow humidity,or
crisperscan be easily removed, freezer. The freshfood compartment and the one inwhichthe humidity is considerably
freezer compartment controlsare located at lower during certain seasons, you can
LEVELING IS IMPORTANT the topfront of the freshfood compartment,move the EnergySaver Switchto "Saves
A refrigerator will not operate properly on- Turn both controlsto "No.5"to start your Energy" which will disconnect thecon
less it islevel and rests firmly on altfourcor- refrigerator, densatedriers and decreasetheamount
ners.Your modelhas four wheets and a of electricity you use.
leveling screw beneath each front corner at Inareasofrelatively highhumidity,the
thebase of the cabinet that can be turned in [[ FRESHFOOD Energy Saver Switch inthe "'ReducesEx-
or out as required. _L L I " 5 • J-- terior Moisture"position will minimize any
1_ - - -collection ofmoisture on the outside sur-
face of the cabinet.
,.EEZE. lJFEATURES
16• _.4J The fresh food compartment is cooled by
Your refrigeratormayrunfor several hours a gentle stream of circulating chilled air.
when you first start it. This is normal and To maintainthe natural flavor, moisture
shouldn'tbe causefor alarm, and nutrition of fresh foods,we recommend
If the floor isnot level and it is necessary In a dayor two, you may decide thatone that you cover open food containers. Dishes
or trayscontaining leftovers should also be
to raise the rear of the cabinet, we suggestor both compartments should be colder or covered to seal in flavors. Storing foods in
rolling the rear wheels on to a piece of ply- warmer. If so,adjust the control(s) as in- plasticbags or in their originalairtightstore
wood or other shimmaterial,structed in the accompanying chart, wrappings reduces the evaporationof mois-
Besure that the two front levelers touch ture from themand lengthens storage time.
the floor to lock thecabinet in place.H
Se ................... ,,5,* SHELVES
I_1I=c'rR|CAL CONNECTION To,t,_t. i s,._......... _,o,o,"s." 1SLIDE-OUT SHELVES move onplastic
AND GROUNDING A,f,_,,,o, ,ooWA,M .... ,.,. ,ooo...... ,to,..t railsand maybe easily pulled forwardfor ac-
Iligh_r number.
This appliance is designed to operate on a _,,, ,.,, ,oDd,o,t,o,_o...,cessto foods placed toward therear. To re-
nominal 115 volt,15 amp., 60 cycleline. Ao_,_._.to_t_ colo. ,....... _,,.movea slide-out shelf,pull ittoward you un-
Turnfr4.iszf.r_ont,Oltonext tilit stops, then liftthefront edge slightly
There should be a separate, grounded cir- Ft_zert_WARM highe'numc=e'.
cult, serving this applianceonly. DO NOT and pull completely out.
usa an extension cord. F,_,rtooCOLD lowernumber
POW_R SUPPLY CORD - Refri_tato_O,¢:F: Set fr(tsh loc.d control O_off. __LI]l
WITH 3-PRONG •
o,oo.o,.oPL00"\1I)USEOFCONTRO'S
IMPORTANT: EXCEPT WHEN START-
ING,DO NOT CHANGE EITHER CON-
_ _ _•|_ TROL MORE THAN ONE NUMBER AT
A TIME.ALLOW 24 HOURS FOR FRUIT EtVEGETABLE CRISPERS
TEMPERATURE TO STABILIZE BE- The fruitand vegetablecrispers slideout
FORE RESt:=I'ING. foreasy access to foods stored within.
Changingeither control will have some ef-Theyare completelyremovable for clean-
GROUNDINGType ing (hand washonly) orfor use elsewhere
WALLRECEPTACLE feet on the temperatureofthe other corn- in your kitchen.The plastic crisper cover
•LOCATIONOFPRONGSONPOWERCORD partment, also serves as a refrigeratorstorage shelf.
PLUGMAy8EDIFFERENTONYOURMODELThe No.9freezer controlsetting is recom- To remove the cover, lift thefrontedge
THAN SHOWN HERE.
This appliance is equipped with a three-mended for short term use only. and pull straight out. To replace the coy-
pronged grounding plug for your protection er, set rear bars on supports and push
against possible electrical shock hazards. It WARM CABINET SURFACES back until front can be lowered into place.
must be plugged into a grounding recepta- At times, the front surfaces of your refrig- Ifa restricted door opening does not per-
cle. Wherea standard two prongwall recep- erator cabinet may be warm to the touch, mit removal of a drawer,tilt crispers and
tacle is encountered,it is the personal re- This isa normal function of your refrigerator, shelf assembly up and remove by lifting
sponsibility and obligation of thecustomer This feature prevents moisture fromcon- straight out.
to have it replacedwith a properlygrounded densing on the outsideof your refrigerator Keep your crisperstightly closed to insure
three-prong wall receptacle.DO NOT, under during humid weather. This condition may crispnessand freshness.Storing leafy vege-
any circumstances, cut or remove the third be noticeablewhen you firststart your refrig- tables, such asceleryand lettuce in plastic
(ground) prong from the power cord. erator,during hotweather, and excessiveor bags reduces the evaporation of moisture
DO NOT use an adapter plug. lengthy door openings, from them.

Leveling Crisper Shelf 2.Refrigeratoris notto be used for a CONNECTING ICE MAKER
Ifthecrispershelf is not level,adjusttheconsiderable time, such as vacations. TO WATER SUPPLY
support leg as shown.Also, turn offthewater supply to the
icemaker in this instance, if practical All installations must bein accordance
__ withlocal plumbing coderequirements.
3. Water supply is to be shut-off for Do not use plastic tubing or plastic fit-
__111_L_ / severalhours.
_1 s_,_ tings because the connection between the
How the Icemaker Works water supply and the refrigerator water
:_- valve inletis under constant pressure.
Water fills the empy cube mold when Also,certain types of plastic tubing may
the freezer compartment has cooled to become brittle with age and crack,result-
freezing temperature. Cold air is forced Jng in water leakage.
directly over mold. When frozen, the cubes Tubing (V4" O.D.) and saddle valve can
MAGNETIC DOOR GASKETS _ be purchasedfrom localhardware stores.
Door gasketsaremagnetized to insure an _ _ Sweat or flare connectioncan be used in-
air tight seal all around. Thesegasketscling [__ _i_lUTu stead ofthecompressionunion, ifdesired.
to thecabinet front, once thedoors are be
closed to within their magnetic range. Note: When using unfiltered well water, it
isadvisable to usea filter inthe water sup-
AUTOMATIC ICE MAKER plyline. Thiseliminates all possibility of
Theautomatic ieemaker is designed to small particlesfromentering thewater
furnish a continual supply of ice cubes,are rotated upand out of themold. The valve.
Withthis useful feature,youno longer sweeper arm ejects theminto theice stor- 1.Working at the right rear of thecabi-
havethe inconvenience of filling icecubeagebin below. Thesensor armsenses
trays,or the frustrationof running out of net, removethe screws fromtheright
ice. ________'_ and leftend of the black fiber panel
The amountof ice produced depends on __q._ thatcovers the machinecompart-
the temperature in the freezer sectionof Icement with an adjustable wrench,and
your refrigerator. The colder the freezer remove the panel. Save the screws
section, the more ice is produced.We sug- t] for later reinstallation as this panel is
II"_--'-- Ice Panrequired for proper and safeoperation
gest you start with your refrigerator and
freezer controls at their mid settings. In _ J of the refrigerator.
mostcases, this is satisfactory. If the door. _j
to the refrigerator or freezerisopened fre- --I_
quently or temperatures in the kitchen are when the bin is full and signals the icemak-
abnormally high, a colder setting may be er to stop ejecting more cubes.Meanwhile, _
necessary, the mold has been refilled and cubes fro- 0
After your modelhas been installed and zensothe new supplyis ready whenneed-
the water supply connected to the icemak- ed. As soonasice is removed from the bin, (_, _" RemoveScrews
er, it may be 8 to 12 hours before the the sensor arm signals that more is need- l_:_-.,
icemaker furnishes any usableice cubes,ed. The icemaker resumes operation by _"_'AccessPanel
The firstone or two harvests will, proba- ejecting ready-and-waiting frozencubes.
bly contain undersized and irregular cubes _"11_
because of air in the supply line. _ 2.Find a 3/8" to 1"vertical COLD wa-
The initial harvest may also containim- tar pipenear the refrigerator. Water
purities from the new water supply piping, pressure must be between 20 and
Therefore,all cubes from the first two or 120 p.s.i. Vertical pipe is preferable,
three harvests should be discarded. Once but a horizontal pipe will work. If a
this initial starting period is past, your horizontal pipe is used,install the sad-
icemaker will perform steadily and dle valve on the top or the side of the
dependably, pipe,noton the bottom.
lee cubes that have been in theice stor-
age bin for aconsiderable length of time 3. Turn OFFthe main water supply and
may pick up off-flavor taste,stick togeth- drain the selected pipe.
er, and gradually become smaller.We sug- 4. Followthe installation instructions
gest that these cubes be thrown away. We
also suggest using an open box of baking For Your Safety that are supplied with the saddle
valve for proper and safe installation.
soda in the refrigeratorfor food odor Do notplace fingers or hands on theaut.,___i_lll=_j/_pipe
absorption,tomatic icemaking mechanismwhile the PiPeClamps
Certain soundsmay accompany the var- refrigerator is plugged in. This will help
ious cyclesof the icemaker. The motor protect you from possible injury. It will also
may have aslight hum--the cubeswill rat prevent interference with moving parts of
tie as they fall into an empty storage the ejector mechanism and theheating BtassSleeve
pan--the water valve may click or "buzz" element that releases the cubes.
occasionally. All ofthesesounds are nor- Under certain rare circumstances,ice BT,.Nut
mal andshould be ignored, cubes may be discolored, usually appear- Manual
The icemaker has awire sensor arm thating withagreen-bluish hue. The cause of shu_off
is connected to ashut-offswitch. This arm this unusual discoloration is apparently a valve
stops the mechanism when the ice cube combination of factorssuch as certain Co_dwater
storage pan is full,and restarts it aftercharacteristics of local waters, householdu.e
several ice cubes have been used. You can plumbing and the accumulation of copper Copp*r
Tubing
use the stop arm to stop all productionssalts in an inactive water supply linewhich
of ice at any time. All you need to do is feeds the icemaker.
raise the arm into the OFF position. Continued consumption of such dis- 5. Route the copper tubing through the
The icemaker should be turned off (arm colored ice cubes may be injurious to floor, wall or sink cabinet to the sad-
health. If such discoloration is observed,die valve location. Form the excess
up) when: discard the ice cubes and contact the deal- tubing into a large loop. This allows
1.Ice storage bin is to be removed for er from whom the refrigerator was movement of therefrigerator without
extended period of time. purchased, disconnecting the tubing.

,TYPICAL WAYSTO CONNECT OUTSIDE
TOWATERSUPPLY Wash regularlywith mild soap and water.
rinse with clear water. Never useabrasive
scouring powders, automobilepolish or fur-
niturepolish.Appliance Wax or a similarpro-
duct will clean and protect the finish satis-
factorily.
Your door gaskets are vinyl. They may
becleaned with abaking soda solution,
_1_ I soap and water or with a mild scouring
powder.
,= Through TheFlCOtTOBasementColdWaterPipe
_DEFROST PAN
6.Locate the brass nut and sleeve, IJDefrost water drains into ashallow pan
which comes withthesaddle valve._/ beneath the cabinet and evaporates.Dur-
Slide themonto the¼" copper tub- ing periods of high humidity, water could
ing. Insert theend ofthetubing into remain in the pan. This pan should be
thesaddle valve asfar as it will go cleaned once a month with asolution of
and tighten the nut with anadjusts- strong soap and water.
blewrench. Turnoff the saddlevalve.
7. Turn ON themain water supplyand . f//_J_--,
flush out thepipe untilthewater runs
clear.At the same time,check for ,.t,_C,.w,S_.Und_,You,.om_
leaks atthe saddle valve.Next pre-
pare toflush out the ¼" tubing. Po-
sition a bucket or other container at To remove thedefrost pan, grasp the base
the open end ofthe¼'"tubingso it _'_ grille at both ends and pull it straight out.
will catch the water. Turn onthe sad- _ Slidethe pan out from underneath the
die valve and allow water to flow un- I___1 cabinet.
til it has cleared.Turn off saddle valve. ,.iS_FORT_A,LS
8. Connect the water line fromthesad-_ILl /_EF_o_rm.
die valve to the water valveas shown .... _L 1 __
Insert the water line into the com- UctderTheSinkToTheColdWater_pe
pression union as far as it will go.
Tighten each brass nut with one
wrench on the nut andthe other _ To replace thedefrost pan,position the
wrench on the compressionunion. _ side flanges to fit over slide railsand push it
Return water line to vertical. Securein until it stops.
watersupplyline clamp.Tighten hose _ To replacebasegrille, align spring clips
nut with pliers,with square opening in cabinet and tapeach
and until grille locks in place.
r Thewaterintettubing assemblyrequired
to completethe water connectionto the CONDENSER
watervalveislocatedinthecrisperdrawer in = Your refrigerator will operate more er-
abag,ThrOugh The WalPToTheUtility RoomColdWater Flpeficiently when the condenser is clean. It
C'>) CAUTION: ice Melter tubing _ld itot boinltlllled should becleaned at least twice a year or
T,_tenReturnwale,su_p=vh_etove.,Ca=ho_enutonwe=weSecure Wae_ou_nupp_mv where temper=ture may fellbelow frmwJ.g, more often if conditions require it. It can
w_ter linewith clamp"_
_I ,,_ be adequately cleaned through the right
front of the base opening. Grasp the base
grille at both ends and pull straight out.
_=_'_1 \/ :l I ,_S ............ ELF_PLACING Then reach through the base opening with
HOSeNut _/_ I ] , I _'_ ....... line your vacuumcleanerattachment to clean
.......... LIGHT BULB thefrontandopenendofthecondenser.water SupplyIr_wate[lines
\ _ ))_V/t_jr_xf_ _ i_['??........ °C'°° DISCONNECT THE POWER .-_1
.......... CO.DBE,=O.E.EPLAC,NG
................ LIGHT BULBS
Lmeassh_n ALWAYSUSE A 40 WA'l-r, STANDARD
9 .Turnon saddle valve. Tighten any BASE, APPLIANCE TYPE BULB WHEN RE-
connections that leak. PLACING A LIGHT. To replace base grille, align spring clips
10. Re-install the fiber panel andsecure CLEANINGwith squareopening in cabinet and tapeach
with the screws removed and saved end until grille locks in place.
inStep 1. DISCONNECT THE POWER
11.Plug in the power cord and push the CORD BEFORE CLEANING GOING ON
refrigerator into place,arranging the INSIDE
copper tubingsothat is does not vi-
brateagainst the back of the refriger- Clean both compartments andinnerdoor VACATION
panelswith mild soapand water. Do not use
ator oragainst the wall. an abrasive powder, solvent, polish cleaner If you willbegone for a month or less,
or undiluted detergent, leave the control knob at its usualsetting.
IMPORTAN3_ Becausethe refrigerator You may noticeaslight discolorationap- During longer absences,(a) removeall
and icemaker arewarm, it maytake up peering at thetop and nearthe center of the food,(b) disconnectfrom electricaloutlet, (c)
to12 hours before the icemaker back wall of the fresh food compartment,clean therefrigerator thoroughly, including
produces the first supplyof icecubes. This is no causefor alarm, but it should be defrost pan, (d) leave doors open to prevent
cleaned off periodically,odor formation.

ENERGY TIPS 3 Usinge socket screwdriver or end 17. Whileholdingthedoor in a closed
wrench, removethescrewsfrom theup- position,takethe center hinge pin that
FOR EFFICIENT ENERGY USE. per hinge. Carefully liftthe door(includ- was removed in step 8,and insert it
ing upper hinge) off thecenter hinge through the left hole of the center
1. Be sure refrigerator is level and ventila- and placeit ona padded surfaceto pre- hinge and into the bottomdoor bush-
tionaround front grille is not blocked, vent scratching.Avoid losingthespacer ing. Makesurethe long pin goes into
2. Check door seals occasionally for leak- that was between the hingeand thecab- thebottom door and the short pin
age. Check at various places, top,but- inst top.goesinto thetopdoor.
tom, sides. 4.Using a putty knife,pry the plug button 18. Set the upper door on thecenter
coverfromthe plasticbushingat thetop hinge,making sure the hingepin
3. Check the temperature; avoid unneces- ofthedoor.Savethecoverforfutureusa. enters the door bushing. When you
sarilycold settings, closethis door, the gasket should ho(d
6. Lift the upperhinge and the spacer it in place.
4.Keepfreezer full to near capacity, less washers fromthedoor and install
cold air is lost during door openings,them at theopposite corner. 19. Making sure to use the same number
of spacers that were originally used
5. Let hotdishescool before putting intore- 5.Position theplug button cover, saved beneath theupper hinge,install the
ftigerator or freezer, from step 4, over the old hinge bush-hinge mounting screws. Beforetight-
6.Cover liquids;if uncovered,the unit must ing and pressit into p_ace, ening these screws, make sure the topof the door is leve_with the cabinet
work longer. 7. Pry out the3 plastic plug buttons top, and the spacebetween thedoor
7.Cleanrefrigeratorcondensercoilsat least from the cabinet top and press them is equidistant across theentirefront.
twice a year. intothe opposite corner. Avoid over-tightening these screws.
Tighten both until they are just snug,
8. Lift thecenter hingepin out of the then turn them in another one-half
SAFETY TIPS bottomdoor and center hinge.Care- turn.
fully lift the lower door off the lower 20. Examine thedoor gasket all around
1. In case of power failure, minimize door hinge and place it on a padded sur- each door, making sureno gaps are
openings.(f power failureisof longdura- face. If themetalhingepin pulls out visible between thegasket andcabi-
tion, protect frozen food by placing of the lower hinge when the door is net. If a gap shows, try stretching the
blocks of dry ice on top ofthepackages, removed, pull it out of the door but-gasket away from thedoor so the
or check with a local frozen foods locker tomand pressit back intothe hinge, magnet willcontact thecabinet sur-
plant about temporary storage. 9.Removethecenter hinge and spacer face.
2.Use the three-pronged plug only with a from the cabinet. Transfer the two 21.Usinga phillips screwdriver,remove the
propedygroundedthree-prongedreceptacle screws fromtheleft end of the divider screws thatattach thenameplate and in-
to provideprotectionfromelectricalshock, bar to theright end. Install thecenter sert to the handles and install themon
Do not use an adapter plug or extension hinge and spacer on the left end of theopposite handles as shown.
cord. the divider bar the sameway it was 22. Invert the handles and install on oppc-
installed on the right end. Tighten sitesidesofthedoors as shown.
3.Unplugrefrigeratorbeforecleaningtheinteri-
or,the condenseror replacinglight bulb.both screws until they arejust snug,
then turn them one-half turnmore.
4.Remove thedoors from out-of-use re-
frigerator. Prevent a child frombecom- 10.Pry the plug cover fromtheplastic
ing accidentally trapped and suf- bushing at thetop of the lower door
focating,and press into the plastic bushing on .,..A.EM.AT=.......
the opposite sideof the door.
CHANGING11 Removethe base grille by grasping at
both endsand pulling itstraight out.
REVERSIBLE 12Remove the lower hinge and spacer.
DOORS 13. Rotate the lower hinge counterclock-
wise90° and install it (including 23. To replacethebasegrille, lineupitsspr-
This refrigerator has been built withthe spacer)to the left legof thecabinet, ing clipswith the squareopenings inthe
doors hinged on the right. If you wish to cabinet and tap each end in until the
hinge the doors on theleft, follow thesein- NOTE: It will takeextra effort to install thegrille locks in place.
structions.If itbecomes necessaryto returnscrews. The screws are self tapping and
the hinges to theright side,merely trans wil_havetocutthreadsinthescrewholes. 24. Replace all food and return thefresh
poseallreferencesto"right'and"left'"____,__ food control to its usual operatingpoem-
when following these instructions, tion.
TOO,SREOUIREB AVOID
Phillips screwdriver UNNECESSARY
End wrench (5/16")
Hex-head socket screwdriver (5/16")
Putty knife SERVICE CALLS
14. Pull the metal hinge pin from the side BEFORECALLINGATECHNICIAN, CHECK
CHANGING BOORSof the lowerhingeand place it,in-THE FOLLOWINGLIST FOR POSSIBLE
1. Turnthe fresh food control to OFF,unplug cluding thespacer washer, into thetop TROUBLES THAT YOU CAN REMEDY
the refrigeratorandremoveallfoodfromthe hole. WITHOUT DIFFICULTY.
interior.15. Pry out the two screw holeplug buttons
on the bottom left side ofthe top door NOISY OPERATION
2. Remove thehandles fromthe doors and lower door. Press in the plug but- • Fan noise--normal air flow.
and set aside. On thesideof the doors tons in theholes ontheright sideof Defrost pan not positioned correctly
thatyou aregoingto installthe hun- both doors.•
dies,removethesmall round screw• Cabinet not level.
hole plugs with a tableknife and press 16. Set the lower door on the bottom
theminto theholes on the opposite hinge, making sure the hinge pin •Weak floor.
sideofthe doors, entersthe bushingin the door bottom. •Dishes rattling against eachother

Additional motorsand controlsare usedto WATER ON FLOOR REFRIGERATOR RUNS TOO LONG
provide theimproved performance ofthis UNDER CABINET •Modern refrigerators arelarger and run
larger capacity refrigerator. Therefore,nor-
mal operatingsounds maybe more noticea- •Defrost panmissingor not positionedcor- colder, which requiresmorerunningtime
hiethan on the model it replaced,rectly • Prolonged door openings
•Water connection loose onwater valve•Control set too cold
SIZZLING SOUND IN FREEZER • Condenser needs cleaning
•Normal sound causedbydefrost water FOODS DRY OUT •Poor air circulationaround condenser
dripping ondefrostmechanism (FRESH OR FROZEN)
• Packages notwrapped orsealed properly REFRIGERATOR WON'T RUN
ICE CUBES EVAPORATE • Crisper not tightly closed • Temperaturecontrol turned toOFF.
• Cold air moving over icecubes causes•Linecord not pluggedin.
cubes to shrink when not usedregularlyMoIErURE COLLECTS ON •No power at electrical outlet.
OUTSIDE SURFACE * Housefuseblownorcircuitbreakertripped.
WARM AIR FROM • Hot humid weather increases condensa-
CABINET BoI-rOM tion. As humidity decreases,moisturewill AUTOMATIC ICE MAKER
•Normalair flow for condenser disappear. NOT OPERATING
•Check EnergySaverControlposition •Stoparmin OFF position
•Water supply turned off
CABINET VIBRATES ODOR IN CABINET • Water pressuretoo low
•Cabinet not level • Odor producing foods should becovered•Freezer too warm
•Weak floor •Interior needs cleaning
FRESH FOOD COMPARTMENT •Defrost pan needscleaning CABINET LIGHT NOT WORKING
•Bulb burned out
TOO COLD • No poweratoutlet
•Refrigeratorcontrolset too coldWATER IN FRESH FOOD
FRESH FOOD COMPARTMENT COMPARTMENT BO'rFOM
TOO WARM •Cabinetnot,eve, IF YOU NEED
•Refrigerator controlset too warm • Drain tube plugged SERVICE
• Freezer control set at coldest position
• Prolonged dooropenings REFRIGERATOR RUNS TOO The model number, serialnumber,and bill
FREQUENTLY of material (BM) number of your model are
listedon a serial plate. The serialplate is Io-
FREEZER COMPARTMENT • Frequent running provides more stable cated attheupper left front corner of the
TOO WARM temperatures lower liner,Refer to allof these numbersin
•Freezercontrol set too warm • Too manydoor openingsanycorrespondencewith your dealer or dis-
•Prolonged door openings •Prolongeddoor openings tributor concerning your model
The manufacturer, whosepolicy is one of continuous product development, reservesthe right to change specificationswithout notice.
Printed ;n U. S.A. 106455-1