MagicBox Torque User manual

Torque
Cordless DECT telephone with answering machine
Torque User Guide.indd iTorque User Guide.indd i 5/2/10 17:13:495/2/10 17:13:49

22
TABLE OF CONTENTS
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Handset range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Signal strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting up the base and handset . . . . . . . . . . . . . . . . . . . 5
Handset battery low warning. . . . . . . . . . . . . . . . . . . . . . . 6
Handset battery performance . . . . . . . . . . . . . . . . . . . . . . 6
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Set the date and time manually. . . . . . . . . . . . . . . . . . . . . 7
Product set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Your Torque handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Your Torque base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
To make a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
To make a call by pre-dialling. . . . . . . . . . . . . . . . . . . . . . . 10
Call from the phonebook. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Call from the calls list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Answer a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Handsfree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
To adjust the volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Secrecy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
To end a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
To switch the handset on/o . . . . . . . . . . . . . . . . . . . . . . . 11
Mood lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using text messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the calls list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using the agenda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Clock & alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Handset settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Base settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Answering machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Simple solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Technical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Torque User Guide.indd Sec1:2Torque User Guide.indd Sec1:2 5/2/10 17:13:575/2/10 17:13:57

3
WELCOME
to your Torque cordless DECT phone with full touch
sensor keypad.
This user guide provides you with all the information
you need to get the most from your Torque handset
and answering machine.
Before you use your product or make your rst
call, please read the important information on
this page.
IMPORTANT NOTE:
Your Torque handset has a high quality full touch
sensor keypad, which is much more sensitive than
a normal telephone keypad. It provides very fast
and responsive keying, however like most new
technology it can take a little time to get used to
using it.
Some tips to help you get the best from your phone
quickly are:
• Pick the handset up by the sides, touching the area
just below the front black touch sensor panel, then
cradle the back of the handset in your hand whilst
you dial.
• During use, avoid touching the keypad area
unnecessarily to prevent accidental triggering of
the keypad.
• The keypad will automatically disable when you
hold the receiver to your ear to reduce the risk of
accidental keypad presses while the handset is held
against the side of your face.
• To ‘wake’the keypad to enable you to dial further
digits, e.g. if you want to access the menu, you just
need to take the handset away from your ear and
wait for the backlight to come on. You can then
dial normally.
• It is very easy to tell when the keypad is disabled, as
the keypad backlight will be o.
• When dialling digits to select from a voice menu, e.g.
Press 1 for accounts..., please ensure that you hold
the handset away from the display area.
• Holding the handset at the top around the display
area may activate the secrecy feature.
Torque User Guide.indd Sec1:3Torque User Guide.indd Sec1:3 5/2/10 17:13:575/2/10 17:13:57

4
PRODUCT SET UP
Where to place your product
It is important that you consider carefully in advance
where your Torque base and cordless handset will be
situated and make sure that they are:
* on a at and stable surface
* within 1.8 metres of a power socket and telephone
socket
* at least 1 metre away from other electrical appliances
to avoid any interference
* away from bright sunlight or heat sources, such as
a radiator
* not in a humid or very damp place such as a bathroom
Note: Your Torque product works by sending radio
signals between the handset and the base. The
strength of the signal depends on where you site
the base. Putting it as high as possible ensures the
best signal.
Handset range
The Torque handset has a range of 300 metres
outdoors when there is a clear line of sight between
the base and the handset. Any obstruction between
the handset and the base will reduce the range
signicantly. With the base indoors and the handset
either indoors or outdoors, the range will normally be
up to 50 metres. Thick stone walls can severely aect
the range.
Signal strength
The icon on your handset indicates when you are
in range. When out of range of the base, Searching...
is displayed and the icon will ash.
If you move out of range during a call, the telephone
call will be disconnected. Move back within range
before you make any further calls. The handset will
automatically re-connect to the base.
Torque User Guide.indd Sec1:4Torque User Guide.indd Sec1:4 5/2/10 17:13:575/2/10 17:13:57

5
IMPORTANT
Only use the mains power adaptor and telephone
line cord supplied with the product.
This equipment is not designed for making
emergency telephone calls when the power fails.
Alternative arrangements should be made for access
to emergency services.
Setting up the base and handset
1. Plug the power adaptor and telephone cable into the
underside of the base.
2. Plug the power adaptor into the mains wall socket
and switch the power on.
3. Remove the battery cover from the back of the
handset and insert the 2 x AAA rechargeable batteries
supplied. Please note the‘+’and ‘-’ markings inside
the battery compartment and insert the batteries the
correct way around. Slide the battery compartment
shut.
WARNING
Never use non-rechargeable batteries. Only use the
approved rechargeable batteries supplied. Using
unapproved batteries will invalidate your guarantee
and may damage the telephone. If you are unsure,
please call the helpdesk on 0845 833 1673.
4. Place the handset onto the base to charge for at least
24 hours. Your Torque handset has ‘reverse charging’
and so can be placed either way around on the base.
Check that the round connector on the back of the
handset is in contact with the round connector in the
middle of the base. When the handset is fully charged
the battery icon in the top right of the display will
indicate this.
5. After 24 hours, plug the telephone line cord from the
Torque base into the telephone wall socket.
Torque multipack users only:
Place each Torque charger within reach of a mains
power wall socket.
1. Plug the mains power adaptor into the power socket
on the underside of the charger and plug the other
end into the mains power wall socket.
PRODUCT SET UP
Torque User Guide.indd Sec1:5Torque User Guide.indd Sec1:5 5/2/10 17:13:595/2/10 17:13:59

6
2. Insert the 2 x AAA rechargeable batteries supplied,
taking note of the ‘+’ and ‘-’ markings inside the
battery compartment, then slide the battery
compartment shut.
3. Place the handset on the charger. Your Torque
handset has ‘reverse charging’and so can be placed
either way around on the base or charger. Check that
the round connector on the back of the handset is
in contact with the round connector in the middle
of the charger. You should let the batteries charge
continuously for at least 24 hours.
The display will show the handset number, e.g. 2, to
show it is registered to the base.
Handset battery low warning
If the icon ashes in the display, you will need to
recharge the handset before you can use it again.
During charging, the icon in the display will scroll.
Handset battery performance
In ideal conditions, fully charged batteries should
give about 10 hours talk time or 100 hours standby
time on a single charge.
Note that new batteries do not reach full capacity
until they have been in normal use for several days.
To keep your batteries in the best condition, leave
the handset o of its charger base for a few hours
at a time.
Running the batteries right down at least once a
week will help them last as long as possible.
The charge capacity of rechargeable batteries
will reduce with time as they wear out, giving the
handset less talk/standby time. Eventually they will
need to be replaced.
The batteries and handset may become warm during
charging. This is normal.
Date and time
Providing you have subscribed to your network’s
Caller Display service, the date and time is set
automatically every time a call is received.
If you do not subscribe to the Caller Display service
or would like to set the correct time and date straight
away, you can set the date and time manually.
PRODUCT SET UP
Torque User Guide.indd Sec1:6Torque User Guide.indd Sec1:6 5/2/10 17:14:005/2/10 17:14:00

7
PRODUCT SET UP
Set the date and time manually
1. On the handset press the button with the line on it,
under ‘Menu’on the display. Scroll to ‘Clock &
Alarm’. Press ‘Select’. ‘Date & Time’ will be displayed,
then press ‘Select’ again. ‘Please wait....’will be
displayed for a few seconds.
2. Using the keypad, enter the date using the format
DD-MM-YY e.g. 04-08-10 for 4th August 2010.
3. Press ‘Save’ and enter the time using the 24 hour
format HH-MM, e.g. 14-45 for 2.45pm.
4. Press ‘Save’ to conrm or RED to return to
standby.
Your Torque handset is now ready for use.
7
Torque User Guide.indd Sec1:7Torque User Guide.indd Sec1:7 5/2/10 17:14:015/2/10 17:14:01

8
YOUR TORQUE HANDSET
8
Power on/o button
Menu / Select / Secrecy
Use to access and select the options
in the menu
Secrecy to mute the microphone
during calls
Redial / Pause / Scroll Up / Volume up
Touch sensor to detect when the handset
is next to your ear
Full graphic display
Talk / Handsfree
End Call / Exit
Phonebook / Scroll Down / Volume down
Recall
Hash - to change the case when
entering letters/editing
Keypad lock
Intercom - to make an internal call
Clear / Back
Clear incorrect input during text editing
Back / to return to previous menu
Torque User Guide.indd Sec1:8Torque User Guide.indd Sec1:8 5/2/10 17:14:015/2/10 17:14:01

9
YOUR TORQUE BASE
9
Mood lighting on
the base to indicate
incoming calls, new
SMS and answering
machine messages
Page / Find
handset key
Use to turn mood
lighting on / o
Mains power socket
Telephone line
socket
Reverse charging
contact, handset
can be placed
either way around
on the base
Torque User Guide.indd Sec1:9Torque User Guide.indd Sec1:9 5/2/10 17:14:025/2/10 17:14:02

10
USING THE HANDSET
To make a call
1. Press GREEN.
2. Dial the telephone number.
To make a call by pre-dialling
1. Enter the phone number (maximum 24 digits).
If you make a mistake press ‘Clear’.
2. Press GREEN to dial the phone number entered.
Call from the phonebook
NOTE
You will rst need to add new entries to the
phonebook. See page 13.
1. Press . The rst entry in the phonebook is
displayed.
2. Scroll up or down to the entry you want.
3. Press GREEN to dial the number.
TIP
Instead of scrolling to browse the phonebook entries,
press the numeric key corresponding to the rst letter
of the entry you wish to locate. For example, pressing
2 will show the entries starting with A. Pressing 2
again will show the entries starting with B, etc...
Call from the calls list
NOTE
You need to subscribe to your network’s Caller Line
Identication service to be able to see the caller’s
number in the calls list.
1. Press ‘Menu’, scroll to ‘Calls Lists’ and press ‘Select’.
2. Use the or to highlight ‘Missed’, ‘Received’ or
‘Dialled’ calls. Press ‘Select’.
3. Scroll or to the entry you want.
4. Press GREEN to dial the number.
Torque User Guide.indd Sec1:10Torque User Guide.indd Sec1:10 5/2/10 17:14:035/2/10 17:14:03

11
USING THE HANDSET
Answer a call
1. When the phone rings , press GREEN to answer
the call. When answering the handset from the
charger base with ‘Auto Talk’ set to On, nothing needs
to be pressed.
Handsfree
1. When the phone rings , press GREEN twice to
answer the call in Handsfree mode. You can press
GREEN each time you wish to switch between
handset and handsfree mode.
WARNING
When the phone is ringing, avoid holding the
earpiece too close to your ear as it may damage your
hearing. Handsfree activation can suddenly increase
the volume in the earpiece to a very high level. Make
sure the handset is not too close to your ear.
To adjust the volume
1. During a call, press or to adjust the earpiece
or loudspeaker volume. The level is shown in the
handset display.
Secrecy
Use the secrecy feature when you would like to speak
to someone else in the same room as you, without
your caller hearing you.
1. During a call, press ‘Secrecy’. ‘Secrecy On’is displayed.
2. Press ‘O’ again to turn the microphone back on and
speak to your caller again.
To end a call
1. Press RED.
After you hang up, the duration of your call is
displayed for 5 seconds.
To switch the handset on/o
1. Press and hold the small power button on the top left
of the handset, just beneath the black touch panel.
2. Press and hold the small power button again to
switch the handset back on.
Torque User Guide.indd Sec1:11Torque User Guide.indd Sec1:11 5/2/10 17:14:045/2/10 17:14:04

12
USING THE HANDSET
Mood lighting
Your Torque base has ‘Mood lighting’which is a ring
of white light around the circular area of the base,
where it sits on a surface. This light will ash when
you have a new incoming call, when you make a
call and when you receive new SMS or answering
machine messages.
To turn the mood lighting on/o.
1. Press and hold the page button on the
underneath of the base for 5 seconds. You will hear
2 beeps. Continue to hold the page button until
the Mood light switches on or o as appropriate.
Torque User Guide.indd Sec1:12Torque User Guide.indd Sec1:12 5/2/10 17:14:055/2/10 17:14:05

13
USING THE PHONEBOOK
The Torque handset phonebook can store up to 100
names and numbers.
NOTE
Numbers can be up to 24 digits long and names up to
12 characters long. Entries are stored in alphabetical
order.
To view and dial phonebook entries
1. Press . Display shows the rst entry.
2. Scroll or to the entry you want. Or to search
alphabetically, press then press the key with the
rst letter of the name, e.g. if the name begins with
N, press 6 twice. The display shows the rst entry
beginning with N. If required, press or to
scroll to the exact entry.
3. Press ‘Options’, then scroll to ‘Show Details’.
Press ‘Select’.
4. Press GREEN or ‘Dial’ to dial the entry displayed.
5. Press RED to end the call (if dialled), or return to
standby.
To view an entry during a call:
1. Press ‘Names’ to open the phonebook menu.
2. Enter the rst letter of the name you want then scroll
or if necessary to the exact name.
3. Press ‘Options’, then scroll to ‘Show Details’.
Press ‘Select’.
4. Press ‘Back’ to cancel the Phonebook display.
5. Press RED to end the call.
To add an entry
1. Press ‘Names’. Scroll to highlight ‘Add Entry’ .
2. Press ‘Select’. ‘Enter Name:’ is displayed.
3. Enter a name using the keypad and press‘OK’.
4. Enter a number. Press ‘OK’ to save. Use the or
to select a melody and press ‘Select’ to conrm.
5. Press RED to return to standby.
Enter a pause
If your Torque handset is connected to a switchboard,
you may need to enter a pause in a stored number.
Torque User Guide.indd Sec1:13Torque User Guide.indd Sec1:13 5/2/10 17:14:055/2/10 17:14:05

14
This gives the switchboard time to nd an outside
line. A Pause is normally stored after the switchboard
access code (e.g. 9)
1. When storing a number, press and hold until the
display shows‘P’. You can then continue storing the
phone number.
NOTE
You can cancel storing an entry at any time during
the process by pressing RED to return to standby.
Entering characters/names
Use the alphanumeric keypad to enter names in
the phonebook.
For instance to enter the name Paul:
P Press ‘7’ once
A Press ‘2’ once
U Press ‘8’ twice
L Press ‘5’ three times
To enter a space press‘0’
Press ‘Clear’ to ‘Delete’ a character.
To edit an entry
1. Press .
2. Scroll or to the entry you want to edit and press
‘Options’. Scroll to ‘Edit Entry’ and press ‘Select’.
3. Edit the name and press ‘OK to conrm. Press ‘Clear’
to ‘Delete’ characters.
4. Press ‘OK’ and edit the number.
5. Press ‘Save’ to conrm.
6. Use the or to select a melody and press
‘Select’ to conrm.
7. Press RED to return to standby.
To change a ringtone
You can change a ringtone assigned to a phonebook
entry, quickly and simply.
1. Press .
USING THE PHONEBOOK
Torque User Guide.indd Sec1:14Torque User Guide.indd Sec1:14 5/2/10 17:14:075/2/10 17:14:07

15
USING THE PHONEBOOK
2. Scroll or to the entry with the ringtone you
want to change and press‘Options’. Scroll to
‘Ringtone’and press ‘Select’.
3. Use the or to select a dierent melody and
press ‘Select’ to conrm.
4. Press RED to return to standby.
To copy an entry (multipack users)
If you purchased a Torque multipack with more than
1 handset, you can copy Phonebook entries to the
other handset/s
1. Press .
2. Scroll or to the entry you want to copy and
press ‘Options’. Scroll to‘Copy Entry’ and press
‘Select’. ‘To Handset’ is displayed. Press ‘Select’.
3. The other handsets registered to the base are
displayed, e.g. Handset 2. Use the or to select
the handset that you would like to copy the entry to
and press ‘Select’ to conrm. ‘Please wait...’
is displayed.
4. On the receiving handset, e.g. Handset 2., ‘Copy
Phonebook? is displayed. Press ‘Yes’ to accept or‘No’
to reject the phonebook entry.
5. Press RED to return to standby.
To copy all entries (multipack users)
If you purchased a Torque multipack with more than
1 handset, you can copy all the Phonebook entries
from 1 handset to the other handset/s
1. Press ‘Names’.
2. Scroll to ‘Copy Phonebook’ and press ‘Select’. ‘To
Handset’ is displayed. Press ‘Select’.
3. The other handsets registered to the base are
displayed, e.g. Handset 2. Use the or to
select the handset that you would like to copy the
entries to and press‘Select’ to conrm. ‘Please wait...’
is displayed.
4. On the receiving handset, e.g. Handset 2., ‘Copy
Phonebook? is displayed. Press ‘Yes’ to accept or‘No’
to reject the phonebook entries.
5. Press RED to return to standby.
Torque User Guide.indd Sec1:15Torque User Guide.indd Sec1:15 5/2/10 17:14:085/2/10 17:14:08

16
USING THE PHONEBOOK
To Delete an entry
1. Press .
2. Scroll to the entry you want to ‘Delete’ and press
‘Options’.
3. Scroll to ‘Delete Entry’and press‘Select’.
4. Display shows‘Delete?’ and the name of the entry.
Press ‘Yes’ to conrm or ‘No’ to return to the options.
5. Press RED to return to standby.
To Delete all entries
1. Press ‘Names’.
2. Scroll to ‘Delete’ Phonebook’ and press ‘Select’.
3. ‘Delete All Entries?’ is displayed. Press ‘Yes’ to conrm
or ‘No’ to return to the options.
4 Press RED to return to standby.
Memory status
You can check how many phonebook entries you
have saved on your handset and how many entries
you still have available.
1. Press ‘Names’.
2. Scroll to ‘Memory Status’ and press ‘Select’. The
following information will be displayed, this is an
example if only 3 phonebook entries have been
saved:
Memory Used: 3
Memory Free: 97
3. Press RED to return to standby.
Torque User Guide.indd Sec1:16Torque User Guide.indd Sec1:16 5/2/10 17:14:095/2/10 17:14:09

17
USING TEXT MESSAGING
Your Torque handset can send and receive text
messages from participating mobile networks and
compatible landline telephones in the UK.
The xed line text service is provided under BT’s
terms and conditions for telephone service. These
can be found by visiting the BT.com website at:
http://www.bt.com/terms
Total number of messages
Your handset can store up to a total of 50 short
messages across all handset Outbox, Draft and
Inboxes.
Memory full alert
If the text mailboxes are full when you attempt to
write a new message the display shows Memory
Full Delete Messages for 2 seconds. You must delete
messages before you can write and send
a new one.
Subscribe to the ‘Text Messaging’ service
When you send your rst text message from your
handset you will automatically be registered for
the service.
You must subscribe to your Network Provider’s Caller
Display service so that you can use Text Messaging
and you must not withhold your telephone number.
On most networks if you normally withhold your
number the 1470 prex will present your number
for you.
A quarterly fee may be payable, please contact your
telephone network provider for more details.
You may also send messages to landline phones
that are NOT text compatible. Messages to non-
compatible lines will be connected to voice text and
delivered in spoken words.
The xed line text service is provided under BT’s
terms and conditions for telephone service. These
can be found by visiting the BT.com website at:
http://www.bt.com/terms.
Cost of the xed line Text Messaging service
There is no subscription charge (other than the
subscription to Caller Display). Visit the BT.com
website (www.bt.com) to nd out how much it costs
to send a text message.
Torque User Guide.indd Sec1:17Torque User Guide.indd Sec1:17 5/2/10 17:14:105/2/10 17:14:10

18
USING TEXT MESSAGING
Send a text message
1. Press ‘Menu’, ‘Text Messaging’ is displayed, press
‘Select’.
2. ‘Write Message’is highlighted. Press‘Select’.
3. Use the keypad to enter your message.
The maximum number of characters in a text
message is 160.
Press # to switch between upper case ABC, lower case
abc letters and digits.
4. Press ‘Options’. Send’ is highlighted.
Press ‘Select’ to send the message. Enter the phone
number or press ‘Search’to open the phonebook,
then scroll to the number you want and press ‘Select’.
Now press‘Send’.
You can also scroll or to:
SAVE
Press ‘Select’ to save the message in the Drafts folder.
INSERT SYMBOL
Press ‘Select’. The symbol table is displayed. Press
or to highlight the symbol you want and
then press ‘Insert’.
INSERT EMOTICON
Press ‘Select’. The Emoticon table is displayed. Press
or to highlight the Emoticon you want then
press ‘Insert’.
INSERT TEMPLATE
Press ‘Select’. The list of Templates is displayed.
Press or to highlight the Template you want
then press ‘Insert’.
NOTE
If you select ‘Send Message’ from within the
Phonebook menu, the phone number of the person
you are sending the text to will be entered for you.
(Press , scroll or to the entry you want to
send the text to. Press ‘Options’. Scroll to ‘Send
Message’ and press ‘Select’).
5. When Sending a message, ‘Sending Message’ will be
displayed, followed by ‘Message Sent’.
Torque User Guide.indd Sec1:18Torque User Guide.indd Sec1:18 5/2/10 17:14:105/2/10 17:14:10

19
USING TEXT MESSAGING
Standard text entry
With standard text entry you can enter a word by
pressing each letter button a number of times to
display the character you want. for example: to write
the word‘Hello’, press 4 twice, 3 twice, 5 three times,
5 three times and 6 three times.
Receiving and reading text messages
When you receive a new text message, an icon is
displayed on the handset as well as ‘You have X new
message/s’on the handset display.
If ‘Mood lighting’ is switched on, this will also ash on
the base.
Read a new message
1. ‘Press ‘Read’, the inbox is opened and the list of
messages is displayed. If you press ‘Back’ the
message is stored in the Inbox for reading later.
2. In the Inbox Scroll (to more recent messages), or
(to older messages) through the list of messages.
3. Highlight the message you want to read and press
‘Read’ or press ‘Back’ to return to the Text Messaging
Menu.
4. Press RED to return to standby.
NOTE
If you are writing a text and you receive a call the text
will be lost.
Read, forward, delete, view and save
numbers of texts in the Inbox.
When you see the new message alert, if you press
‘Back’the message is stored in your Inbox so that you
can read it later.
1. Press ‘Menu’, ‘Text Messaging’ is displayed, press ‘Select’.
If you have new messages you will go straight to the
Inbox, if not scroll to Inbox and press‘Select’.
2. Scroll or to the message you want to read and
press ‘Read’. Scroll or through the message.
3. Press ‘Options’ and scroll or to:
REPLY
Press ‘Select’, Write your reply then press ‘Options’ and
select ‘Send’.
FORWARD
Press ‘Select’. The message is displayed. Press
‘Options’, ‘Send’ is highlighted. Press ‘Select’ and
enter a number or search for the number and then
press ‘Send’.
Torque User Guide.indd Sec1:19Torque User Guide.indd Sec1:19 5/2/10 17:14:115/2/10 17:14:11

20
USING TEXT MESSAGING
MESSAGE DETAILS
You can see who sent the message and then
call them. Press ‘Select’, the ‘Sender’s number is
displayed. Press ‘Dial’ if you want to call the number.
USE NUMBER
To call the sender, press ‘Select’. ‘Call’ will be displayed.
Press ‘Select’ to call the sender OR to save the
number, scroll to ‘Save’ and press ‘Select’. Enter a
name and press OK, edit the number if required then
press ‘Save’. Scroll or to the ringtone and
press ‘Select’. The number is saved in the phonebook.
‘Delete’
Press ‘Select’. Press ‘Yes’ to conrm or ‘No’ to cancel.
Edit or send texts in the Drafts box
1. To open the Drafts box, press ‘Menu’, ‘Text Messaging’
is displayed. Press ‘Select’.
2. Scroll to ‘Drafts’ and press ‘Select’.
3. Press ‘Edit’ to edit your message content.
4. Press ‘Options’ and scroll or to ‘Send’, ‘Save’,
‘Insert Symbol’, ‘Insert Emoticon’, ‘Insert Template’ or
‘Message Type’.
Forward or ‘Delete’ texts in the Outbox
1. To open the Outbox, press‘Menu’, ‘Text Messaging’
is displayed. Press‘Select’.
2. Scroll to ‘Outbox’ and press ‘Select’.
3. Scroll or to the message you want and press
‘Read’. Scroll or through the message.
4. Press ‘Options’ and scroll or to ‘Forward’
or ‘Delete’.
5. Press RED to return to standby.
Edit templates
1. Press ‘Menu’, ‘Text Messaging’ is displayed.
Press ‘Select’
2. Scroll to ‘Templates’ and press ‘Select’.
3. Scroll or to the template you want to edit
and press ‘Options’. Scroll or to ‘Edit’ and
press ‘Select’.
4. Use the or to scroll through the template,
together with the keypad and ‘Clear’ to edit the
template. Press ‘Save’.
5. Press RED to return to standby.
Torque User Guide.indd Sec1:20Torque User Guide.indd Sec1:20 5/2/10 17:14:125/2/10 17:14:12