Maimiao MX5 User manual
1
Key Features
Smart Security Light Camera
User Manual
Installation Steps
2.Download and install
“TuYa Smart” app
>Open app
>Registered account
1.Fix the Wall Mouting Plate
> Connect the power cable
>Mount the Camera housing
> Power it up
3. Click Add Device > select Security &
Sensors > Smart Camera
> click Other Mode(upper right)
> select Mode
> click next step
Spare Parts List
Cover Pad
(Option)
PIR
Main Light
Top Light
Wall Mouting Plate
Speaker
Reset Button
MIC
Micro SD
Bottom Lock Screw Hole
Indicator
Top Lock Screw
Power wire via Hole
Camera Lens
●1080P Full HD Security Camera
●1200 Lumen White LED Lamp
● APP View Live Video & Playback
●PIR & Sensor Dual Detection
●Two Way Audio
●APP Push Notifications
●APP Control Light & Adjust Brightness
●Waterproof
X8
X2
X2
X1 X1
Bracket
(Option)
★NOTE: This product only supports QR code & Smart Mode & Wired
Network(Option,Only for Ethernet Version)
★ Product as AP mode are not supported; Please refer to the following APP
Installation And Initial Configuation
TM
Maimiao MX5
2
Product Installation Instruction
AA
AA
B B
D
C
C
D
A.Screw hole
B.Square outlet fixing screw
hole
C.Rectangleoutlet fixing
screw hole
D.Round bracket nut fixing
hole
E.Green Power socket
G.LAN Socket(Option)
A. (For no Outlet):Mark 4 A position points with a pen>Drill holes above marked points>Tap in 4 plastic
plugs> Lock 4 screws to fix the Wall Mouting Plate on the wall.
B. (For Square Outlet):Use 2 M4 screw to aim the outlet screw hole >lock the screw to fix the Wall
Mouting Plate and square Outlet .
C. (For Rectangle Outlet):Use 2 M4 screw to aim then outlet screw hole> lock the screw to fix the Wall
Mouting Plate and Rectangle Outlet .
D.(For Circular Outlet): First lock 2 long M4 screws on the circular bracket >use two short M4 screws fix
the circular bracket to outlet>place the Cover Pad on the bracket >Insert 2 bracket screws after aligning the
Plate holes > lock the nut to finish Wall Mouting Plate fixed to the circular bracket.
EF
LAN
3. Align the Housing back Rectangle gap
with the Wall Mouting Plate
> press the Housing close to the Plate
>lock the up & bottom lock screws to
complete the installation.
Recommend installation height is 2.5M:
Distance from the ground to the bottom of
the product.
For Circular Outlet (option): as shown in the
figure above
first lock two long M4 screws on the circular
bracket.
>use 2 short M4 screws to fix the bracket on the
outlet.
> place Cover Pad between bracket and plate
>insert two screws into the screw holes of the
plate.
>lock two spare nuts at D position to fix the plate
& circular bracket.
1.Hold the side of Wall Mouting Plate by hand, slightly rock up and down,
then pull out the Wall Mouting Plate
2.First made the power cable via to the F hole> connect the cable to green
power socket (E position)> use screwdriver to fix the cable tight>according to
the installation environment>select one installation mode (A to D) to fix the Wall
Mouting Plate on the wall.
Top Lock Screw
Bottom Lock Screw Hole M4 Screw
M4 Screw
G
Cover Pad
3
APP Installation And Initial Configuation
1.Preparation
After power on 1 minute
> check the device is waiting for installation (red
Indicator light is flashing ),if not please reset the
device(Press and hold the reset button for 5 seconds
then release)
>Cell phone connected to the same WiFi router
>Check the WiFi signal strength displayed by the cell
phone at the place where the device is installed is no
less than 2 bars.
2.Use APP store to search "Tuya Smart" >download and
install>open Tuya Smart app>Registered Account
3. Open APP main page > click Add device > Select Security & Sensors > Smart Camera > Other
Mode (upper right) to select Mode
● QR code mode:Focus the Cell Phone Screen’s QR code on the Lens(the distance is about 20
cm)>after the QR code is identified,the device will make beep sound>Click I Heard a Prompt>Waiting
for Conneting device(about 1 minute)>click Done.
● Smart mode: Input WiFi password>next step>waiting for Conneting device(about 1 minute)>click
Done.
●Wired Network(option): First insert network cable to the Lan Socket >observe that the green and
yellow indicator lights are flashing>click next step>click found device>(about 1 minute)>click
Done.(only for support ethernet device）
● AP Mode :(not supported)
QR code Mode
4
1.Red indicator : blinks means searching network.
Blue indicator: blinks means network connection is successful.
meanwhile searching the server. Always lights means device online.
Yellow indicator: blinks means Ethernet active.
Green indicator: blinks means Ethernet access successful.
2. Reset to factory setting: After powered on 1 minute , press and hold
the reset button for more than 5 seconds then release, and hear the
voice"reset complete" means reset to factory setting successful.
Fault type Indicator Status Solution
No Power Indicator off Check the power connection status
Boot Failed Red & Blue LED
always lights Power off 5 seconds, then power on again
Connect to
WiFi Failed Red LED always blinks
Check the W iFi signal strength near the
installation of the device through the
mobile phone (it needs to be greater than
or equal to 2), check whether the W iFi
password is correct, if the password is not
correct, please click return, reenter
password.
Connect to
Server
Failed
Blue LED always blinks Check whether the network is connected
to the Internet normally
Common Fault List
Main Parameter
Operation Status Description
Product Name Smart Security Light Camera
Model Number MX5
Camera Resolution 1920*1800（1080P)
Viewing angle 110°
Operational Temperature -20℃ to +50 ℃
WIFI IEEE 802.11b/g/n
Power Supply 100-240VAC ,50/60HZ,0.2A
Power 25W(MAX)
Weight 980g
Dimensions(H x W x D) 300mmx111mmx112mm
5
This device complies with part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference
(1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that
may cause undesired operation.Changes or modifications not expressly approved by the
party responsible for compliancecould void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.If this equipment does cause
harmful interference to radio or television reception,which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.-- Connect the
equipment into an outlet on a circuit differentfrom that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be
installed and operated with minimum distance between 20cm the radiator your body: Use
only the supplied antenna. Changes or odifications made to this equipment not expressly
approved by manufacturer name) may void the FCC authorization to operate this
equipment.
FCC ID:2AWK9-MX5
NOTE Contact us
Manufacturer:
Shenzhen Maimiao Innovation Technology Co., Ltd
Address:
1F No. 116, Long shi Road, Xin lian Community, Long gang District,
Shenzhen ,China
Tel:
+86075528998667
Email:
Table of contents
