Mami GiSMo User manual

GiSMo
GSM/GPRS Programmable
Communicator
21 Hubert Mathew Road, Illiondale, 1609
Tel [phone] Fax [phone]
www.mami.co.za
M000153
The GiSMo 2 is a multi-purpose GSM unit used for monitoring and controlling devices via SMS and Mobile network
One time programmable missed call or one time pin
2000 Names & Numbers (intercom)
Non-restore time
Programmable via SMS or USB
Programmable: Trigger times per input
Event logging onboard (offline version) or web(online version)
Input names
Reverse polarity protection (24V)
Input action (Call, SMS, trigger output, GPRS)
Access control time for missed call
Input Delay (positive and negative)
Auto airtime check and recharge commands
GiSMo
Start up
For ease of setup we recommend using a USB cable(GiSMo4) and make use of PC software to program.
Please make sure that the SIM card in use does not have a security PIN number. This can be disabled by putting the SIM
card in a mobile phone and removing the PIN request. Insert the SIM card as show in Figure 3.
The GiSMo must have a power supply that can handle up to 2A spikes form SMS and GPRS usage. It is therefore
recommended to connect to a battery or good power supply.
The GiSMo is operational when the green LED flashes slowly (1 flash every 2seconds (offline version) or 1 flash every 3
seconds (online version)
Any problem with the SIM card (such as incorrect insertion or PIN number) will be indicated by the RED LED turning on
IMPORTANT!
All numbers need to contain the international dialing code (27 for South Africa) without a leading + or 0 eg: 27821234567 is correct
SMS Programming
žAll commands are confirmed with a reply SMS to the person sending the message or to the status number (if set)
žAll SMS commands start with an asterisk ‘*’ followed by a 4 alphanumeric password, eg. *2222 2222 is the default password
žAll commands and settings are converted to upper case.
Resetting
žHold down both buttons and apply power, continue to hold the buttons for 10 seconds and the green and red LEDs will begin to flash
alternately, release the button and wait for approx 4minutes while the memory is erased.
Hardware Features:
3 inputs
2 voltage free relay outputs
Built-in lead acid charger
Open Serial Port (optional-GPRS)
Built-in Radio Receiver (optional)
Compatible Accessories:
Intercom 2 button home intercom
Topo/SLIM remote control relay activation

SMS Format: *2222 ADDS=XXXXXXXXXXX
Example: *2222 ADDS=27821231234
This will add the selected telephone number to SMS when any input is triggered
SMS Format: *2222 ADDD=XXXXXXXXXXX
Example: *2222 ADDD=27821231234
This will add the selected telephone number to be called when the relative input is triggered.
Numbers are added sequentially so the first number added will be called when input 1 is triggered, second number when input 2 triggered
etc
INPUT MONITORING
SMS (Send SMS on input trigger)
CALL (Call on input trigger - intercom)
DELETING INPUT SMS/DIALING NUMBERS
SMS Format: *2222 DELT=XXXXXXXXXX
Example: *2222 DELT=27821231234
This will delete the SMS/Dialing number 27821231234
In1
In2
In3
Relay1
Relay1
Relay2
Relay2
Sim Card
2 1
+24V
+12V
- -
In1
In2
In3
Relay1
Relay1
Relay2
Relay2
Sim Card
2 1
+24Vin
+13.8V battery output
- -
Solar or
24V Input
12V Lead
Acid Battery
Gate Motor
or
Power Supply
Connections
12V
Input
24V
Input
1A Charge
Current
GSM Antenna
GSM Antenna
GiSMo 2
SMS PROGRAMMING
M000153

Automatic Way: To add number for a missed call it is also possible to hold down the two buttons until the ORANGE LED begins to
flash. This means the units is in programming mode. Any phone calling the unit within the next hour will automatically be added to
the system.
*2222 ADDN=27821231234,123,1,1 This will add 27821231234 as unit 123, user 1 for missed call on relay 1
ADDING MISSED CALL NUMBERS
Manual Way (SMS):
EXAMPLE:
OR
*2222 ADDN=27821231235,123,3,2 This will add 27821231234 as unit 123, user 3 for missed call on relay 2
*2222 DELN=0,123,3 Delete telephone number for unit 123 user 3
or
DELETE MISSED CALL NUMBER
*2222 DELT=27821231234 Delete number 27821231234
TRIGGER OUTPUT ON MISSED CALL
PUL[A] A = 1-4 (input number) Pulses according to the Pulse time set in Relay Time Below
SET[A]=B A = 1-4 (input number)
B = 1,0 (1=on, 0=off)
Example: *2222 SET1=1 Turn on Relay 1
*2222 PUL2 Pulse Relay 2
CHANGING INPUT NAME DESCRIPTIONS AND INPUT SETTINGS
This will program the SMS of “FRONT DOOR OPENED” when input 1 is triggered for 2seconds (see below for setting the number to
report to)
*2222 NRTI=X : X = Non Restore Time in 20ms
ADVANCED INPUT OPTIONS:
Example
*2222 SETI=1,0,Front_Door,0,OPENED,CLOSED,100,100
*2222 TTIM=X : X = Trigger Time in 20ms
INV : 1 = Inverted, 0 = Normal
DELAY_ON : Input delay to trigger in 100ms (eg 200 =20s)
TXTHIGH : High Message (10 characters)
0 : Always 0
Name : Input Name (20 characters)
A : INPUT Number (1-4)
DELAY_OFF : Input delay to Restore in 100ms (eg 200 =20s)
SMS Format: *2222 SETI=A,0,Name,INV,TXTHIGH,TXTLOW,DELAY_ON,DELAY_OFF
TXTLOW : Low/Restore Message (10 characters)
Query airtime using command *2222 AIRT?
Status/Master Number *2222 STATNO=278212345678
System Password : *2222 PASS=1234 Set password to 1234
Systems name : *2222 NAME=XXXXXX X is up to 16 characters
Add airtime using command *2222 AIRT=XXXXXX X is the reacharge voucher pin
X=0(0.5s), 1-9 = 1-9s
Set Add Airtime Command: *2222 AAIRT =*100*01* (recharge pin will be added to *100*01* )
set in AAIRT
Relay Time *2222 RELAY[A]=X A=1(Relay1), A=2(Relay2)
Set the Airtime Retrieval Command *2222 GAIRT=*136#
Get input and output status *2222 STATUS?
set in GAIRT
Clear All numbers *2222 CLEAR=Y
HANG up time *2222 HANG=X X is in seconds
SYSTEM COMMANDS
TRIGGER OUTPUTS VIA SMS
M000153

INPUT MONITORING NUMBERS
SMS Format: *2222 ADDI=XXXXXXXXXXX,A,B,PPMMDD,TT,DUR
X = Telephone number
B = INPUT Memory location (1-9)
A = 0 (always unit 0)
PP = INPUT NUMBER HEX NUMBER REPRESENTING THE INPUT (eg 06 = 0110 = INPUT 2 and INPUT 3, 0F for all)
MM = MONITOR TYPE (LOW,HIGH,TRIGGER,NON-RESTORE) HEX NUMBER (0F for all)
DD = ACTION (SMS,DIAL,RELAY1 ON,RELAY1 OFF,RELAY2 ON,RELAY2 OFF)
TIME= ACCESS TIME (HOURS 0-23) (Blank for none)
Example:
*2222 ADDI=27821231234,0,1,0F0F01 Send an sms to 27821231234 when any input is triggered
DURATION = ACCESS DURATION HOURS (Blank for none)
Delete the number
*2222 DELN=0,0,3 Delete Input Action number 3 (see input action (B) above 1-9)
*2222 DELT=27821231234 Delete telephone number 27821231234
NUMBER MANAGMENT
*2222 ADDN=27821231234,1,3,2A,0,0,0,0 add number 27821231234 that triggers relay 2 on missed call as well as auto-answer the call
TIME = Access Start time (0-23) (25 = ALL)
D = Dial Times (1-254)
Example
DUR = Access duration time (hours)
U = Unit number (1-9999)
SMS Format: *2222 ADDN=XXXXXXXXX,U,N,0012DAM,P,D,TIME,DUR
1 = Missed call Relay1
N = User Number (1-9)
2 = Missed call Relay2
D = Disable Dialing
A = Auto answer call
M = Disable Missed call
X= Mobile Number with country code (excluding +)
P = Missed call times (1-254)
ADVANCED NUMBER MANAGEMENT SETTINGS
M000153