Mammooth MMT A170 704 User manual

MMT A170 704
ELECTRIC CAR POLISHER
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.

Safety instructions
1. General safety instructions for power tools
1). Job security
2). Electrical safety
3). Personal safety
Retain all safety notices and instructions for future use.
Warning! Read all safety warnings and instructions. Failure to follow the safety
instructions and instructions can result in electric shock, fire and / or serious injury.
The term “power tool” used in the safety instructions refers to mains-operated power tools
(with a power cord) and to battery-operated power tools (without a power cord).
a) Keep your work area clean and well-lit. Cluttered or unlit work areas can lead to
accidents.
b) Do not work with the power tool in an explosive environment in which there are
flammable liquids, gases or dust. Power tools generate sparks that can ignite the dust
or fumes.
c) Keep children and other people away while using the power tool. If you are distracted,
you can lose control of the device.
a) The power tool connector must match the socket. The plug must not be modified in
any way. Do not use adapter plugs with protective earthed power tools. Unmodified
plugs and matching sockets reduce the risk of electric shock.
b) Avoid body contact with earthed surfaces such as pipes, heaters, stoves and refrigera
tors. There is an increased risk of electric shock if your body is grounded.
c) Keep power tools away from rain or moisture. Water getting into a power tool increas
es the risk of electric shock.
d) Do not misuse the cable to carry the power tool, to hang it up or to pull the plug from
the socket. Keep the cord away from heat, oil, sharp edges, or moving parts of the
device. Damaged or tangled cables increase the risk of electric shock.
e) If you work with a power tool outdoors, only use extension cables that are also
suitable for outdoor use. Using an extension cord suitable for outdoor use will reduce
the risk of electric shock.
f) If operating the power tool in a damp environment cannot be avoided, use a residual
current circuit breaker. The use of a residual current circuit breaker reduces the risk of
an electric shock.
a) Be attentive, pay attention to what you are doing, and use your common sense when
working with a power tool. Do not use a power tool when you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while using the
power tool can result in serious injury.
b) Wear personal protective equipment and always protective goggles. Wearing personal
protective equipment, such as a dust mask, non-slip safety shoes, hard hat or hearing
protection, depending on the type and use of the power tool, reduces the risk of
injuries.
c) Avoid unintentional start-up. Make sure that the power tool is switched off before you
connect it to the power supply and / or the battery, pick it up or carry it. Accidents can
occur if you have your finger on the switch while carrying the power tool or if you
connect the device to the power supply when it is switched on.
2

d) Remove adjustment tools or wrenches before switching on the power tool. A tool or
wrench in a rotating part of the device can cause injuries.
e) Avoid abnormal posture. Make sure you have a secure stance and keep your balance
at all times. This gives you better control of the power tool in unexpected situations.
f) Wear suitable clothing. Do not wear baggy clothes or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothing, jewelry or long hair can be caught
in moving parts.
g) If dust extraction and collection devices can be fitted, ensure that they are connected
and used correctly. Using a dust extractor can reduce dust hazards.
a) Do not overload the device. Use the power tool designed for your work. With the right
power tool, you can work better and more safely in the specified performance range.
b) Do not use a power tool with a defective switch. A power tool that can no longer be
switched on or off is dangerous and must be repaired.
c) Pull the plug out of the socket and / or remove the battery before making device
settings, changing accessories or putting the device away. This precaution prevents
the power tool from starting accidentally.
d) Keep unused power tools out of the reach of children. Do not allow people to use the
device who are not familiar with it or who have not read these instructions. Power
tools are dangerous when used by inexperienced people.
e) Maintain power tools with care. Check whether moving parts are working properly and
not jamming, whether parts are broken or damaged in such a way that the function of
the power tool is impaired. Have damaged parts repaired before using the device.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are easier to guide.
g) Use the power tool, accessories, tool bits etc. in accordance with these instructions.
Take into account the working conditions and the work to be performed. The use of
power tools for purposes other than those for which they are intended can lead to
dangerous situations.
Have your power tool repaired only by qualified specialists and only with original spare
parts. This ensures that the safety of the power tool is maintained.
Even if you operate this power tool properly, there are always residual risks. The following
dangers can arise in connection with the construction and design of this power tool:
Damage to health resulting from hand-arm vibrations if the power tool is used over a
long period of time or is not properly operated and maintained.
3
4). Use and treatment of the power tool
5). Service
2. Residual Risks
Warning! This power tool generates an electromagnetic field during operation. This field
can, under certain circumstances, affect active or passive medical implants. To reduce
the risk of serious or fatal injuries, we recommend people with medical implants to
consult their doctor and the manufacturer of the medical implant before operating the
machine!

• The device is intended for polishing painted surfaces e.g. cars, boats, doors etc. and
for sanding sheet metal, metals, plastics, wood or similar materials. Only use polishing
and grinding discs with a 180 mm Ø Velcro connection.
• The manufacturer assumes no liability for improper use or changes to the machine.
• The device is intended for private use only. The device is not suitable for commercial
use.
• Also observe the safety instructions, the installation and operating instructions as well
as the general accident prevention regulations.
Intended use
Technical data
Note:
1. The vibration value refers to surface grinding. Other applications can cause different
levels of vibration.
2. The sound and vibration values were measured in accordance with EN 60745-1 and
EN 60745-2-3.
3. The specified vibration value has been determined according to a standardized test
method and can be used to compare different power tools with one another. This value
is also suitable for assessing loads for the user caused by vibrations in advance.
4
Warning! Depending on how you use the power tool, the actual vibration values may
differ from those specified.
Take measures to protect yourself against vibration exposure. Take into account the
entire work process, including times when the power tool is working without load or when
it is switched off.
Suitable measures include regular maintenance and care of the power tool and tool
attachments, keeping your hands warm, regular breaks and good planning of work
processes.
Model
Voltage / Frequency
Power
Spindle size
Rated speed
Rated capacity max.(Diameter of the grinding tool)
Sound pressure level, LpA
Sound power level, LWA
Vibration,ah
Protection class
MMT A170 704
230 - 240 V~ (AC) / 50 Hz
1200 W
14mm
600-3400min-1
Ø180mm
87.63dB(A),k=3dB
98.63dB(A),k=3dB
13.078m/s², k=1,5 m/s²
II

Explanation of symbols
Description
5
Read the instruction manual carefully and completely before use.
This power tool corresponds to protection class II. This means that the power tool is
equipped with reinforced or double insulation.
This symbol indicates that this power tool must not be disposed of with household
waste. Follow the disposal instructions in these operating instructions.
Be vigilant and be aware of general hazards. This warning sign is shown in connection
with other instructions or symbols, which, if ignored, could result in damage to people
or power tools.
Corresponds to the prescribed safety regulations
Before doing any work on the power tool (e.g. transport, assembly, retrofitting,
cleaning and maintenance work) and when not in use, pull the power plug out of the
socket!
Wear protective goggles!
Wear hearing protection!
Wear a dust mask!
5
4
7
3
2
1
9
8
610
B1

6
1. On / Off switch
2. Locking button
3. Electronic speed control
4. Spindle lock button
5. Polishing / sanding pad
6. Polishing attachment
7. Handle
8. 2x Allen screw
9. 2x carbon brushes
10. Allen key
Assembly
Handle
Clamp the handle (7) over the brackets provided on the machine head and fasten it on
both sides with the Allen screws (9).
Press the shaft lock button (4) and turn the polishing / sanding pad (5) until the shaft lock
engages.
Screw the polishing / sanding pad firmly onto the machine spindle (B4) while pressing
the shaft lock button.
The polishing / sanding pad (5) has a Velcro pad on which the polishing and
Abrasive discs with Velcro can be easily put on and taken off.
Place the polishing or grinding discs on the edge and apply pressure to the center of the
plate. (B5)
To peel off, grasp the edge of the polishing / sanding discs and pull them off.
The handle can be mounted for right or left hand use. (B2) (B3)
Polishing / sanding pad
Change polishing attachment / grinding wheels

7
Working with the polishing / grinding machine
Cleaning and care
Installation
Switching on / off
Working with the polishing / grinding machine
• Polishing:
• Grinding:
Correct and regular care is not only important for the safe use of this power tool, it can
also extend the service life of the power tool.
Warning! Switch off the power tool and disconnect it from the power supply by
pulling the plug before you carry out maintenance and cleaning work on it, in order
to avoid hazards such as electric shock.
- Replace the polishing attachments with sanding pads with Velcro pads.
- For coarse sanding, use grinding wheels with a coarse grain.
- For fine sanding, use sanding discs with a fine grain.
- For the perfect finish, do a sanding test before starting work.
- Put the entire surface of the grinding wheel on and process the workpiece with even
circular or straight movements, without exerting excessive pressure.
When using wax and polishing agents, observe the manufacturer's processing instruc-
tions.
ATTENTION: Apply polishing agent to the surfaces to be processed and allow to dry
according to the manufacturer's instructions.
Switch on the machine, preselect the speed on the setting wheel (3) of the electronic
speed control and machine the area to be worked with even movements. Let the machine
rest on the polishing surface without applying additional pressure.
Care tips:
- Wash, wax and polish your car regularly every 2 to 3 weeks.
- Wash the car thoroughly with clear water before polishing.
- Do not use household detergents as additive to water. They can damage the paintwork
and the wax layer.
- Remove insects, bird droppings or other stubborn dirt such as tar stains with cleaning
agents designed for this purpose.
- Apply waxes and polishes according to the manufacturer's instructions.
- Apply window cleaner with a rag or sponge. This will prevent the painted surface from
getting dirty.
- Press the on / off switch (1), the machine starts up.
- Release the on / off switch to switch off.
- For longer work, press the on / off switch (1), then press the locking button (2).
- To release the locking button, press the on / off switch (1), the device switches off.

8
a) Clean the power tool with a damp cloth and a little soap. Use paintbrushes or brushes
for hard-to-reach areas.
b) In particular, clean the ventilation openings and the tool holder with a cloth and brush
after each use.
c) Remove particularly stubborn dust residues in inaccessible places with compressed
air (max. 3 bar).
Note: Do not use any chemical, alkaline, abrasive or other aggressive cleaning agents or
solvents; these can attack and damage the surfaces of the power tool.
There are no user-serviceable or repairable parts inside. Never try to repair the power
tool yourself. Always contact a qualified specialist.
If the mains connection cable of this power tool is damaged, it must be replaced with a
special connection cable available from the manufacturer or his customer service.
a) Clean the power tool as described and let it dry completely.
b) Store the power tool in the original packaging if you do not intend to use it for a long
period of time.
c) Always store the power tool out of the reach of children in a well-ventilated and dry
place.
d) Always switch off the power tool before transporting it.
e) Always carry the power tool by the handles provided.
f) Protect the power tool against tilting, vibrations and shocks, especially when transport
ing it in vehicles.
The meaning of the crossed-out garbage can: Do not dispose of electrical devices in
the household waste, use the collection points in your community. Ask your local
authority about the location of the collection points, If electrical devices are disposed
of in an uncontrolled manner, dangerous substances can get into the groundwater
and thus into the food chain during weathering, or flora and fauna can be poisoned for
years. If you replace the device with a new one, the seller is legally obliged to accept
the old one for disposal at least free of charge
Repair and Maintenance
Storage and transport
Disposal

9
IT Dichiarazione di conformità CE SK Prehláŝenie o zhodě ES
DE EG - Konformitätseklärung SI ES izjava o skladnosti
FR Declaration de conformité CE HU CE-megfelőségi nyilatkozat
UK EC delaration of conformity RO Declaraţie de conformitate CE
CZ Prohláŝeni o shodě EU BA/HR EG – izjava o konformnosti
PL Deklaracja zgodności WE
Inter Cars S.A.
ul. Powsińska 64,
02-903 Warszawa
Poland
Warszawa 05.07.2021
IT Con la presente dichiariamo che l’articolo di seguito descritto, in base alla sua concezione e costruzione ed alla messa in
circolazione da parte della è conforme ai requisiti fondamentali di sicurezza e salute delle direttive CE.
DE Hiermit erklären wir, dass der nachfolgend beschriebene Artikel aufgrund seiner Konzipierung und Bauart sowie in
der von in Verkehr gebrachten Ausführung den einschlägigen grundlegenden Sicherheits-und
Gesundheitsanforderungen der EG- Richtlinien entspricht.
FR Avec la présente nous declarons que l’article décrit ci-après repond en matièrede conception et de construction ainsi que dans
son modèle commercialisé par la aux esigences fondamentales de sécurité et sanitaires et aux directives
communitaires applicable.
UK We herewith declare that the following product complies with the appropriate basic safety and health requirements of the EC
directives based on its design and type, as brought into circulation.
CZ Timto prohlašujeme že následovné popsane zboží svou koncepci a konstrukci rovněž i provedením, jenž bylo dáno do prodeje
společnosti, odpovidá přislušným základnímbezpečnostním a zdravotním požadavkům směrnic EU.
PL Niniejszym deklarujemi iż niżej określony artykul, w formie wprowadzonej na rynek przez, spelnia ze względu
na project I construcję podstawowe wymagania bezpieczeństwa pracy oraz ochrony zdrowia narzucane przez dyrektywy WE.
SK Týmto prehlasujeme že nasledovne popisovaný tovar na základe svojho návrhu a konštruckcie, ako aj prevedenia uvedeného
spoločnost’ou do prevádzky, in zdravstvenim zahtevam, ki so v skladnosti z EU smernicami.
SI S tem izjavljamo mi da je opisani proizvod na osnovi njegove nasnove in vrste konstrukcije kot tudi pri
prodajo spuščena izvebda odgovarja temelijnim varnostnim in zdravstvenim zahtevam, ki so v skladnosti z EU smernicami.
HU Ezennel nyilatkozunk hogy a következőkben leírt árucikk koncepciójában és kiviteli módjában valiant az által
forgalomba hozott kivitelében megfelel az EU rá vonatkozó alapvető biztonsági-es egészségvédelmi előirásainak.
RO Noi declaram de proprie raspundere ca articolul descris mai jos, pe baza concepţiei şi tipului sau constructiv sale, precum
şi al execuţiilor puse în circulaţie de, se conformeaza cerinţelor pentru securitatea muncii şi sanataţii ale
directivelor UE în materie.
BA/HR Ovim izjavljujemo da u slijedećem opisani proizvod na osnovu njegovog koncipiranja i načina gradnje kao i izlaganja izdanog
od odgovara jasmin, osnovnim sigurnosnim i zdravstvenim zahtjevima EG smjernica.
IT Prodotto
DE Produkttyp
FR Produit
UK Product
CZ Produktu
PL Produktu
SK Produktu
SI Proizvoda
HU Termek típusa
RO Termek típusa
BA/HR Termek típusa
IT Direttive CE
DE Anwendbare EG-
Richtlinien
FR Directives CE applicables
UK Applicable EC directives
CZ Směrnice EU
PL Dyrektywy WE
SK Aplikovatel’né smernice
EU
SI Uporabljene ES smernice
HU EU Műszaki Irányelvek
RO Directive UE applicabile
BA/HR EG – smjernice
IT Norme armonizzate
applicate
DE Angwandte harmonisierte
normen
FR Normes armonisées
applicable
UK Applicable harmonized
standards
CZ Aplikované harmonizačni
normy
PL Zastosowano
zharmonizowane normy
SK Použité harmonizované
normy
SI Uporabljani usklajeni
normativi
HU Alkalmazott harmonizált
szabványok
RO Norme armonizzate
aplicabile
BA/HR Primijenjene
harmonizirajuće norme
COD MMT A170 704
NAME Electric Car polisher
USE HOBBY / DOMESTIC
2006/42 / EC
2014/30 / EU
guaranteed by Inter Cars S.A. ul.
Powsińska 64, 02-903 Warszawa
EN 60745-1:2009+A11
EN 60745-2-3: 2011+A2+A11+A12+A13
AfPS GS 2019:01 PAK