Taurus RT-XS 28 User manual

N26704
280W
MULTI SANDER
INSTRUCTION MANUAL
AFTER SALES SUPPORT
TEL: [phone]
EMAIL: [email protected]
MODEL NUMBER RT-XS 28

Multi Sander
What your 1 year warranty means
Great care has gone into the manufacture of this product and it should therefore provide you with years
of good service when used properly. In the event of product failure within its intended use over the
course of the rst 1 year after the date of purchase, we will remedy the problem as quickly as possible
once it has been brought to our attention. In the unlikely event of such an occurrence, or if you require
any information about the product, please contact us via our after sales support services, details of
which can be found in this manual and on the product itself.
Welcome Section
Congratulations on choosing to buy a TAURUS® product.
All products brought to you by TAURUS® are manufactured to the highest standards of performance and
safety, and, as part of our philosophy of customer service and satisfaction, are backed by our
comprehensive 1Year Warranty.
We hope you will enjoy using your purchase for many years to come.
Table of Contents
1. Safety regulations
2. Layout
3. Proper use
4. Technical data
5. Before starting the equipment
6. Operation
7. Cleaning and maintenance
8. Disposal and recycling
9. Storage
2
After Sales Support TEL: [phone] EMAIL: [e-mail]

3
After Sales Support TEL: [phone] EMAIL: [e-mail]
1
2 3
124
9 10 11 7
a
b
c
10
a
5
1
5
3
6
8

4
After Sales Support TEL: [phone] EMAIL: [e-mail]
5
76
8
4
9
1
11 c
ab
e
6 d 8 d 7
a
6 a b
6
a
9
I 0
2
+
-
3

5
After Sales Support TEL: [phone] EMAIL: [e-mail]
GENERAL SAFETY RULES
SAVE THESE INSTRUCTIONS
1. Work area
a. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a. Power tools plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tool. Unmodied plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk
of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power
tools may result in serious personal injury.
b. Use safety equipment. Always wear eye
protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying
power tools with your nger on the switch or
plugging in power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to rotating part of the power tool may
result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
g. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
4. Power tool use and cars
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and tool bits
etc. in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use of
the power tool for operations different from
those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
WARNING! Read all instructions Failure to
follow all instructions listed below may result
in electric shock, re and/or serious injury. The
term ’’power tool’’ in all of the warnings listed
below refers to your mains-operated (corded)
power tool or battery-operated (cordless) power
tool.

6
After Sales Support TEL: [phone] EMAIL: [e-mail]
Important!
When using equipment, a few safety
precautions must be observed to avoid injuries
and damage. Please read the complete
operating manual with due care. Keep this
manual in a safe place, so that the information
is available at all times. If you give the
equipment to any other person, give them
these operating instructions as well.
We accept no liability for damage or accidents
which arise due to non-observance of these
instructions and the safety information.
1. Safety regulations:
The corresponding safety information can be found
in the enclosed booklet.
CAUTION
Read all safety regulations and instructions.
Any errors made in following the safety
regulations and instructions may result in an
electric shock, re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
1. Keep your work area tidy. Untidiness in the
workplace can lead to risk of accidents.
2. Take into account inuences from the
surrounding environment. Do not expose
electrical appliances to rain. Do not use
electric tools in damp or wet environments.
Provide good lighting. Do not use electric
tools near ammable liquids or gases.
3. Protect against electric shock. Avoid bodily
contact with earthed parts, for example
pipes, heaters, ovens and fridges.
4. Keep other people away! Do not let other
people gain access to the tool or cable,
keep them away from your workplace.
5. Store the equipment safely and securely.
Unused equipment must be stored in a dry,
locked room, out of the reach of children.
6. Do not overburden the tool. It will work
better and safer when used within its quoted
capacity range.
7. Use the correct tool. Do not use weak tools
or attachments for heavy duty work. Never
use the electric tool for purposes other than
that for which it is designed, for example
do not use the hand-held circular saw to fell
trees or cut branches.
8. Wear suitable work clothes. Do not wear
loose clothing or jewellery. It could get
caught in moving parts. Rubber gloves and
non-slip shoes are recommended when
working outdoors. If you have long hair,
wear a hair-net.
9. Wear safety goggles. Use a dust mask when
working on dusty jobs.
10. Do not use the cable for purposes other
than that for which it is designed. Do not
carry the tool by the cable and do not use
it to pull the plug out of the socket. Do not
carry the charger by the cable and do not
use is to pull the plug out of the socket.
11. Secure the workpiece. Use clamps or a
vice to hold the workpiece securely. This is
safer than using your hand, and also makes
it possible to use the machine with both
hands.
12. Take care that your feet are a stable
distance apart. Avoid abnormal working
postures. Make sure you stand squarely and
keep your balance at all times.
13. Take good care of your tools. Keep
your tools sharp and clean to keep them
working safely and efciently. Observe the
maintenance instructions and the notes
about changing tools. Check the plug and
cable regularly, and if they are damaged,
have them replaced by a certied expert.
Check extension leads regularly andreplace
these if damaged. Keep handles dry, clean
and free from oil and grease.
14. Pull the power plug. When not in use, before
maintenance work or when changing tools,
such as saw blade, drill and machine tools of
any kind.
“Caution - Read the operating
instructions to reduce the risk of inquiry”
Wear ear-muffs.
The impact of noise can cause damage
to hearing.
Wear a breathing mask.
Dust which is injurious to health can be
generated when working on wood and
other materials.
Never use the device to work on any
materials containing asbestos!
Wear safety goggles.
Sparks generated during working or
splinters, chips and dust emitted by the
device can cause
loss of sight.

7
After Sales Support TEL: [phone] EMAIL: [e-mail]
15. Always remove keys and wrenches
after use. Before switching on, make sure
that all keys and wrenches have been
removed from the tool.
16. Avoid unsupervised operation.
Never carry mains-powered tools with your
nger on the switch. Make sure the switch is
OFF when connecting the tool to the mains.
17. Outdoor use of extension cables.
For outdoor use, only use approved and
appropriately labelled extension cables.
18. Be alert at all times.
Observe your work. Work carefully. Never
use the electric tool when you are
distracted.
19. Check the appliance for damage.
Before using the equipment further, check
that safety equipment or slightly damaged
parts are in good working order and function
correctly. Check that the moving parts are
working correctly, that they do not jam, and
that no parts are damaged. Make sure that
all parts are tted correctly, to ensure that
the equipment remains safe to use.
Damaged safety devices and parts must be
repaired or replaced by experts in a
customer service workshop, unless
otherwise stated in the manual. Damaged
switches must be replaced by a customer
service workshop. Do not use equipment for
which the on-off switch does not correctly
function.
20. Important!
For your own safety, only use accessories
and auxiliaries which are stated in the
operating instructions or which have been
recommended or indicated by the
manufacturer. Use of any other attachments
or accessories than those stated in the
operating instructions or in the catalogue
could lead to personal injury.
21. Repairs should only be done by an
expert. This electric tool complies with the
pertinent safety regulations. Repair work
may only be carried out by an electrician.
Otherwise there is a risk of accidents for the
operator.
22. Attach the dust extraction system.
If there are apparatuses available for the
attachment of the dust extraction system,
make sure these are connected and used.
2. Layout
1. Additional handle
2. Operating switch
3. Speed controller
4. Handle
5. Dust container
6. Rectangular sanding/grinding plate
7. Eccentric sanding/grinding plate
8. Triangular sanding/grinding plate
9. Punch for sanding/grinding paper
10. Chip extractor adapter
11. Allen key
3. Proper use
The equipment is designed for the
grinding/sanding of wood, iron, plastic and
similar materials using the appropriate
grinding/sanding paper. The machine is not
suitable for wet grinding/sanding.
The equipment is to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user / operator and not
the manufacturer will be liable for any damage or
injuries of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be
voided if the machine is used in commercial,
trade or industrial businesses or for equivalent
purposes.

8
After Sales Support TEL: [phone] EMAIL: [e-mail]
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect
working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the
appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever
necessary.
• Switch the appliance off when it is not in
use.
• Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment’s
construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is used.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
prolonged period or is not properly guided
and maintained.
Warning! The electric power tool generates an
electromagnetic eld during operation. Under
certain circumstances this eld may actively or
passively impede medical implants. To reduce
the risk of serious or fatal injuries, we recommend
persons with medical implants to consult their
doctor and the manufacturer of the medical
implant prior to using the equipment.
5. Before starting the
equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating
plate are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Installing the dust container (Figure 2/Item 5)
• Slip the dust container (5) onto the
vacuumcleaner connector (a).
• The dust is extracted directly through
the grinding/sanding paper and the
grinding/sanding plate and into the dust
container.
4. Technical data
Mains voltage: 230 V ~ 50Hz
Power input: 280W
Orbits: 0 - 10,000rpm
Protection class: Class II /
Weight: 2.2 kg
Rectangular sanding/grinding plate:
Grinding/sanding area: 140 x 115mm
Abrasive paper size
(Velcro fastening system)
140 x 115mm
Abrasive paper size
(Clamping system)
180 x 115mm
Eccentric sanding/grinding plate:
Grinding/sanding area: Ø 125mm
Abrasive paper size Ø 125mm
Triangular sanding/grinding plate:
Grinding/sanding area: 82 x 109 x 106mm
(a x b x c; Fig. 1)
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745
LpA sound pressure level 80 dB(A)
KpA uncertainty 3 dB
LWA sound power level 91 dB(A)
KWA uncertainty 3 dB
Wear ear-muffs.
The impact of noise can cause damage to
hearing.
Total vibration values (vector sum of three
directions) determined in accordance with EN
60745.
Vibration emission value ah = 14.495 m/s2
K uncertainty = 1.5 m/s2
Additional information for electric power tools
Warning!
The specied vibration value was established in
accordance with a standardized testing method.
It may change according to how the electric
equipment is used and may exceed the specied
value in exceptional circumstances.
The specied vibration value can be used to
compare the equipment with other electric power
tools. The specied vibration value can be used
for initial assessment of a harmful effect.

9
After Sales Support TEL: [phone] EMAIL: [e-mail]
• Place the rectangular sanding/grinding
plate (6) together with the tted sanding/
grinding paper (a) onto the punch (9) for
the sanding/grinding paper). (Fig. 8)
• Now punch the required holes into the
sanding/grinding paper.
• Remove the punch (9) from the sanding/
grinding plate (6).
• Check the correct position of the punch
holes in the sanding/grinding paper plate.
5.5.2 Fasting the sanding/grinding paper with
Velcro fastening system
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the
extraction holes on the sanding/grinding paper
and the sanding/grinding disk are aligned.
5.6 Triangular sanding/grinding plate (Fig. 6)
Fit the triangular sanding/grinding plate (8) to
use the equipment as delta sander/grinder.
Fastening the sanding/grinding paper:
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the
vacuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.7 Eccentric sanding/grinding plate (Fig. 6)
Fit the eccentric sanding/grinding plate (7) to
use the equipment as eccentric sander/grinder.
Fastening the sanding/grinding paper:
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the
vacuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
6. Operation
6.1 Switching the equipment ON/OFF
(Fig. 9/Item 2)
To switch on: Slide the ON/OFF switch (2)
forwards (position I)
To switch off: Slide the ON/OFF switch (2)
backwards (position 0)
6.2 Speed control (Fig. 7/Item 3)
To pre-select the speed turn the knurled screw
(3) on the switch.
Plus Direction: High Speed
Minus Direction: Lower Speed
5.2 Installing the dust extractor adapter
(Figure 2/Item 10)
Slip the dust extractor adapter (10) onto the
vacuum cleaner connector (a) as shown in Figure
2. Connect the dust extractor adapter to a
suitable dust extraction system.
Important.
For health safety reasons it is imperative that you
use a dust container or a dust extraction system.
5.3 Adjusting the additional handle (Fig. 3/4)
• The additional handle engages in 4 positions
(90° steps).
• Pull the additional handle upwards (1). (Fig.
3)
• Turn the additional handle (1) into the
required working position. (Fig. 4)
• Let go of the additional handle.
• Ensure that the additional handle is securely
engaged in the required position.
5.4 Fitting/removing the sanding/grinding
plates (Fig. 5/6)
• Use the Allen key (11) to remove the Allen
screw (a) and the washer (b) (Fig. 5).
• Then remove the sanding/grinding plate (c)
(Fig. 5).
• To assemble, proceed in reverse order.
• When tting the sanding/grinding plate
(6 / 8) make sure that the 4 rubber stoppers
(d) are inserted into the corresponding
mounts (e). (Fig. 6)
• Check that the sanding/grinding plate is
secure.
5.5 Rectangular sanding/grinding plate
(Fig. 6/7/8)
Fit the rectangular sanding/grinding plate (6) to
use the equipment as an orbital sander/grinder.
5.5.1 Fasting the sanding/grinding paper with a
clamping system)
Use of sanding/grinding paper with the
corresponding dimensions and perforations (Fig.
7):
• Press the lever (a) upwards.
• Insert the sanding/grinding paper (b) into
the open clamp and close the clamp.
• Lay the sanding/paper over the oscillating
plate so that the paper is taut and clamp it
again.
• Make sure that the perforations in the
sanding/grinding paper coincide with the
oscillating plate.
Use of sanding/grinding paper without the
appropriate dimensions and perforations (Fig.
7/8):
• Cut the sanding/grinding paper to t the
corresponding dimensions.
• Fit the sanding/grinding paper to the
sanding/grinding plate as described above.

10
After Sales Support TEL: [phone] EMAIL: [e-mail]
6.3 Working with the equipment:
Important. Never hold the workpiece you wish to
sand/grind in your hand. Secure the workpiece on a
sturdy surface or with a vise.
• Place the whole surface area of the sanding
disk on the material.
• Switch on the machine and move it with gentle
pressure over the workpiece completely
circular movements or moving it to and fro
and up and down.
• Use a coarse paper for coarse sanding and a
ner paper for nish sanding. You can nd the
best paper for the job by means of testing.
Important.
The dust generated when working with the machine
may be harmful.
• Always wear goggles and a dust mask when
carrying out sanding/grinding work.
• Everybody who uses the machine or enters the
workplace must wear a dust mask.
• Do not eat, drink or smoke at the workplace.
• Do not use the machine on paints which con-
tain lead.
7. Cleaning and maintenance
Always pull out the mains power plug before
starting any cleaning work.
7.1 Cleaning
• Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible.
• Wipe the equipment with a clean cloth or blow
it with compressed air at low pressure.
• We recommend that you clean the device im-
mediately each time you have nished using it.
• Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the
plastic parts of the equipment. Ensure that no
water can seep into the device.
7.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualied electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualied electrician.
7.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8. Disposal and recycling
The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
9. Storage
Store the equipment and accessories out of
children’s reach in a dark and dry place at
above freezing temperature. The ideal storage
temperature is between 5 and 30 °C. Store the
electric tool in its original packaging.

11
After Sales Support TEL: [phone] EMAIL: [e-mail]

m
After Sales Support TEL: [phone] EMAIL: [e-mail]
06/2011
Art.Nr: 44.191.33_11010