Mantion WIDOOR User manual

INSTALLATION INSTRUCTIONS
DOOR MOTOR
WIDOOR
VERSION 3-02 EN
2, rue des Métiers
21110 –Genlis
Tel.: [phone]
http://www.mantion-smt.fr

2
GUARANTEE - IMPORTANT SAFETY INSTRUCTIONS.
These instructions must be followed in the interest of personal safety; Keep these
instructions.
This motorization is exclusively designed for opening and closing sliding internal doors. It must not
be used for any purpose other than that specified in these instructions. The manufacturer or
supplier shall not be liable for any damage resulting from improper use thereof. The user alone
shall be solely liable and assume any risks arising from improper use of the product.
This door motor must be installed by persons fully aware of the hazards involved with electric
currents, and having all qualifications to work on domestic installations in accordance with good
practice.
Follow all these instructions because faulty installation can cause injuries.
The assembly steps must be followed, as must the operating instructions, and safety rules must
always be heeded.
Before installing the door motor, check that both the driven part and the supplied motor are in
good mechanical condition; and that the structure has the necessary load-bearing capacity for our
product in its entirety.
The electrical installation must be done according to prevailing national standards. The power
supply must be compatible with our product (voltage and frequency as specified on the product)
Do not connect the device without first checking that the control circuit is disconnected from the
power supply.
Check the installation frequently to detect any signs of wear and tear or damage. Do not use the
device if it needs repairing or adjusting.
Always disconnect the power supply when cleaning or carrying out any maintenance or servicing
tasks on the product.
Never modify or fit any additional parts to the device that may compromise safety without
MANTION SMT's written permission.
The user alone is solely and entirely responsible for any breach of these safety rules, and any
damage resulting therefrom.
The product must be stored indoors in a dry place at a temperature of between 0 °C and +50 °C.
When fitting it, the installation engineer must heed accident prevention instructions and the
standards in force in the country.
Do not immerse the gear motor in water or splash it.
Do not dispose of it in fire or bring it into contact with flame or any heat source.
Do not use household products or chemicals to clean it.
Do not dispose of the packaging in the environment; treat waste according to the standards in
force in the country.
Keep products, devices and documentation out of reach of children.
Do not let children play with the fixed control devices. Keep remote controls out of reach of
children.
This product may be used by children over the age of 8 and by persons with reduced physical,
sensory or mental capabilities, or inexperienced persons, if they are properly supervised, or they have
been given proper instructions on the safe use of the product, and possible risks have been removed.

3
Children must not play with the product. Cleaning and maintenance must not be carried out by
children, without supervision.
The manufacturer or supplier shall not be liable for any damage resulting from any other use of the
product. If replacing the product, only use MANTION SMT or MANTION SMT-approved products.
Terms of the guarantee
MANTION SMT products come with a 5 (five) year guarantee from the date of delivery.
The guarantee is limited, as decided by MANTION SMT, either to replacement or to repair of
products that MANTION SMT recognizes as faulty, with the proviso that:
1. Subject to MANTION SMT's written permission to return the products, the said products are
returned to MANTION SMT forthwith with the details of the fault and a copy of the
installation engineer or dealer's bill stating the date of installation.
2. The products have been stored, installed, maintained and used in accordance with
MANTION SMT's instructions and specifications.
The guarantee is strictly limited to the provisions of this clause, and any other guarantee or
liability, including loss of profits or damage directly or indirectly resulting from the sale or use of the
products, is excluded.
MANTION SMT shall in any event only be liable for the motorization. The guarantee does not
apply in case of overvoltage or short-circuiting resulting for instance from connection errors,
weather conditions such as lightning, etc. The guarantee does not cover normal wear.

4
Summary:
1. Technical characteristics...........................................................................................................5
2. Kit contents................................................................................................................................7
3. Installation diagram ...................................................................................................................7
4. Pre-installation checking............................................................................................................8
5. Motor installation .......................................................................................................................9
5.1. Gear motor establishment............................................................................................................................ 9
5.2. Belt fixing on the door (not included).........................................................................................................10
5.3. Free pulley installation (not included) ........................................................................................................ 10
6. Electrical connection................................................................................................................11
6.1. External accessories connection ................................................................................................................. 12
6.2. Peripherals connections.............................................................................................................................. 13
6.3. Power supply connection (terminal C1)...................................................................................................... 14
7. Protection cover installation.....................................................................................................16
8. Operating modes.....................................................................................................................17
8.1. Switches settings......................................................................................................................................... 17
8.2. Closing modes ............................................................................................................................................. 17
9. Bringing into service................................................................................................................18
10. Parameters settings.............................................................................................................19
10.1. Peering a smartphone............................................................................................................................. 19
10.2. Disabling all smartphones .......................................................................................................................19
10.3. Adjustable parameters via mobile application .......................................................................................19
11. Wireless setup instructions (Radio product only) .................................................................20
11.1. Radio specifications.................................................................................................................................20
11.2. Peering a switch or a remote control (transmitter)................................................................................ 20
11.3. Disabling a switch or a remote control (transmitter) .............................................................................21
11.4. Disabling all transmitters (switches, remote control, etc.)..................................................................... 21
11.5. Other informations .................................................................................................................................21
12. Further information...............................................................................................................22
12.1. LED color code......................................................................................................................................... 22
12.2. Restart after power outage.....................................................................................................................22
12.3. Obstacle detection .................................................................................................................................. 22
13. Diagnostic aid.......................................................................................................................23

5
1. Technical characteristics
This product is used for opening and closing automatically sliding doors (one or two doors). It is
designed for domestic or professional use.
General informations
Reference
K0000256 –Wire control
K0000266 –Radio control
Designation
Sliding door motorization
Technology
Belt transmission
Connectivity
Radio (433,92 MHz) / Bluetooth (BLE4.1)
Size
L= 150 mm, T= 45 mm, H= 205 mm
Maximum weight per door
10 –80 kg or 10 –50 kg for double doors
Max speed
350 mm/s *
Max distance
6 m
Frequency of use
500 cycles per day (maximal recommended)
Guarantee
5 years
* Measure is given for indicative purpose, using a 50kg door.
Electrical
Power Supply
80 –264 VAC
Frequency
47 –63 Hz
Nominal Power
65 W
Current max
1,5 A at 115 VAC / 1 A at 230 VAC
Isolation class
Class II
Protection
Internal fuse 2,5 AT
Recommended power cable
3G0,75 mm² for a maximum length of 20 m
Environment
Protection rating
IP 20
Operating temperature
+5 °C < T < +40 °C
Options
Command
Wired: push button or radar
Radio: transmitter 433 MHz
Command and parameter
setting
Smartphone application (Android or IOS)
Lock output
Allow to plug a locker (24 VDC, 500 mA max.)
Safety input
Allow to plug a safety input

6
Setting Parameters
Max opening speed
50 mm/s –350 mm/s *
Max closing speed
50 mm/s –200 mm/s *
End opening speed
End closing speed
Increase or decrease the speed at the end position
Deceleration at the opening
Adjust the deceleration according to the weight of the
door
Timer before closing the door
0 s –60 s
* Measure is given for indicative purpose, using a 50kg door.
Normative / directive compliance
Equipment safety
EN60335-1, EN60335-2
People security
Obstacle detection
impact force < requirement of the standard EN16005
EMC
EN61000-6-1, EN61000-6-2, EN61000-6-3, EN61000-6-4
ROHS Directive
2002/95/C

7
2. Kit contents
Motorization
Screws and
adhesive band
Electrical
terminal
Protection
cover
3. Installation diagram
Recommended components (not included):
x 4
Fixing bracket
Free pulley
Stoppers x 2
Belt
Track

8
4. Pre-installation checking
Operating reserve: 150 mm in width and 45 mm for thickness.
Do not use locking stoppers.
150 mm min
70 to 77 mm
45 mm min
Porte

9
5. Motor installation
5.1. Gear motor establishment
In the track, slide the nuts fixing the system.
Tighten the two M6 screws.
Note: if the motorization is between walls, put adhesive bands.
Nuts x 2
M6 screws

10
5.2. Belt fixing on the door (not included)
5.3. Free pulley installation (not included)

11
6. Electrical connection
This product is delivered with 2 shunts between terminals 4 and 5 of C2 and C3.
These shunts are necessary for the system; remove them ONLY if you replace them with
security cells.
Pay attention to your safety:
- The electrical installation must be carried out in accordance with the national
standard in force, as well as any obligations foreseen by the law and/or by all
obligations in force, laid down for this purpose.
- Electrical connection must take place without voltage, do not connect the sector
before having disconnected all assembly operations.
C2
Opening control 1
C3
Opening control 2
C4
Output lock control
C1
Power supply

12
6.1. External accessories connection
Function
Functionality
description
Peripherals
characteristics
Abbreviation
N°
Terminal / Connection description
C1
Power
supply
It allows to
supply the
product
80 –264 VAC
47 –63 Hz
65 W
L
Live
N
Neutral
Protecting Earth
C2
Opening
control 1
It allows to use
an external
command
(pushbutton,
non-contact
pushbutton,
radar, security
cell, etc.)
Power
consumption
1 A max
(5 W in 24 V)
24 V
1
External command power
GND
2
INPUT 1
3
Door opening (link with GND)
GND
4
Common wire used for TEST,
SAFETY and INPUT
SAFETY 1
5
The door stays open if it’s not
connected to GND
TEST 1
6
Connect the input Test radar
(necessary to be conform with the
EN16005 standard)
C3
Opening
control 2
It allows to use
an external
command
(pushbutton,
non-contact
pushbutton,
radar, security
cell, etc.)
Power
consumption
1 A max
(5 W in 24 V)
24 V
1
External command power
GND
2
INPUT 2
3
Door opening (link with GND)
GND
4
Common wire used for TEST,
SAFETY and INPUT
SAFETY 2
5
The door stays open if it’s not
connected to GND
TEST 2
6
Connect the input Test radar
(necessary to be conform with the
EN16005 standard)
C4
Lock
It allows to use
a locking
system with a
power applied
or removed
(suction or
electromagnet)
Power
consumption
500 mA max
(12 W in 24 V)
N.O.
1
Connect it if the system is locked
without power supply
N.C.
2
Connect it if the system is locked
with power supply
24 V
3
Connect one of the two wires of
the lock

13
6.2. Peripherals connections
6.2.1. Opening control (C2 and C3)
By default, "Opening control 1" is set for a radar and "Opening control 2" is set for a pushbutton.
These settings can be set via the mobile application.
Pushbutton switch (C0001290):
Add a shunt between the terminals 4 and 5.
Non-contact pushbutton (C0001300):
Add a shunt between the terminals 4 and 5.
Radar (C0001310):
Add a shunt between the terminals 4 and 5.
Radar with security cell and test cell (C0001320):
Brown
White
Green
Yellow
Brown
White
Green
Yellow
Power supply
Radar
Brown
White
Yellow
Green
Blue
Red
Brown
White
Green
Yellow
Red
Blue
Power supply
Radar
IR

14
6.2.2. Security system (C2 and C3)
Security cell (C0003760):
6.2.3. Locking system (C4)
Fail secure (locking system without power supply):
Fail safe (Locking system with power supply):
Fail safe suction:
Fail secure
Fail safe
C0013750 C0013760 C0013765
60 kg 180 kg 180 kg

15
6.3. Power supply connection (C1)
The installation must be equipped (L, N, PE) with a two-pole external circuit-breaker and a
disconnector (or selector switch) on the primary side in order to isolate the product if
necessary.
Supply voltage
80 –264 VAC
Frequency
47 –63 Hz
Power rating
65 W
Recommended power
cable
3G0,75 mm² for a maximum
length of 20 m
C1
Power supply
L Live
N Neutral
T Protective Earth

16
7. Protection cover installation
After electrical connections, put the protection cover.
Step 1. Arrange wires.
Step 2. Put the protection cover in openings.
Step 3. Press the protection cover against the product.
Be careful with the wires.
Step 4. Put the screws.
2
1
3
4

17
8. Operating modes
8.1. Switches settings
Switch
OFF
ON
1
Radio and Bluetooth peering
Stoppers learning
2
Switch the direction of motor rotation
3
Automatic mode: Automatic
closing of the door
Manual mode: Opening and
closing of the door on request
4
Bluetooth disable
Bluetooth enable
Note: by default, switches 1, 2 and 3 are in OFF position and switch 4 is in ON position.
8.2. Closing modes
Automatic mode (switch 3 on OFF):
Press on the control button
The door is opening
Automatic closing after few seconds (adjustable
with mobile application)
Press the button when the door is open
The door stays open
Press the button during the closing
The door is opening
Manual mode (switch 3 on ON):
Press on the control button
The door is opening and stays open
Press the button when the door is open
The door is closing
Press the button during the closing
The door is opening
Note: radar use is not compatible with this closing mode.

18
9. Bringing into service
Before bringing into service this product, check you can move the doors manually effortless. A bad
installation with a bad doors alignment or high frictions can damage the motors. Check that the
product and accessories are correctly connected.
This product is equipped with a stoppers learning push button (BP Prog) which determines the
movement of each door.
The motor won’t work as the stoppers learning has not been carried out.
Modus operandi:
a. Powering the system.
b. If you want to use a radio product, refer to the wireless setup instructions, part "6. Peering".
c. Turn ON the switch 1.
d. Start the stoppers learning by pressing of BP Prog.
The system closes in slow speed. Then opens and closes in slow speed.
Finally, it performs an opening and closing cycle.
When the door is closed, the system is operational.
Note: if, after carrying out the learning cycles, the door is open instead of close, turn ON the switch
2 and do another learning.
Switch
Pushbutton BP Prog
LED

19
10. Parameters settings
It’s possible, with the "Widoor" application, to adjust settings. This app can be
downloaded on stores.
10.1. Peering a smartphone
a. Turn OFF the switch 1 and turn ON the switch 4.
b. Press briefly one time on the BP Prog.
c. The LED lights up in magenta.
d. When the LED is lighted: start the peering on your smartphone.
e. The LED flashes quickly and then goes out: the smartphone is peered.
Note: It is possible to peer several products on a same smartphone, or until 3 smartphones on the
same product. For that, repeat the operations below.
If a 4th smartphone is paired, the product desynchronized the oldest used smartphones. To pair
this smartphone, remove the product in the Bluetooth setting of the smartphone.
10.2. Disabling all smartphones
a. Turn OFF the switch 1.
b. Press briefly one time on the BP Prog.
c. The LED lights up in magenta.
d. When the LED is lighted: Press and hold down the BP Prog during 10 seconds
e. The LED flashes quickly and then goes out: all smartphone are disabled.
Note: All smartphones and all radio switches will be deleted. All settings will be reseted to default
values.
10.3. Adjustable parameters via mobile application
Opening speed
Range: 50 mm/s - 350 mm/s *
Closing speed
Range: 50 mm/s - 200 mm/s *
End of open speed
End of close speed
It allows to adjust a soft arrival on the stoppers
Opening deceleration
It allows to adjust the opening deceleration
Delay before closing
Time: 0 to 60 s
* Measure is given for indicative purpose, using a 50kg door.
Additional features are available in the mobile application.

20
11. Wireless setup instructions (Radio product only)
11.1. Radio specifications
Frequency: 433,92 MHz
Transmitter range: approximately 70 m line-of-sight*
* Propagation of radio waves varies according to the medium they traverse. The range of the radio waves
will also vary according to the type of construction:
In case of bad reception, use the radio repeater. Ref. C0004760.
11.2. Peering a switch or a remote control (transmitter)
a. Turn OFF the switch 1.
b. Press briefly one time on the BP Prog.
c. The LED lights up in magenta.
d. When the LED turns on: press the “open” and “close” buttons simultaneously on the switch.
e. The LED flashes quickly and then goes out: the switch is peered.
Note: it is possible to peer several products on a same switch, or several transmitters on the same
product. For that, repeat the operations below.
Close
canal 1
Close
canal 2
Open
canal 1
Open
canal 2
Open
Close
Plasterboard Plaster / Wood
90 to 100 %
Brick / Conglomerate
65 to 95 %
Reinforced concrete
10 to 70 %
Metal
0 to 10 %