Markant MATRIX PRO User manual

Matrix Pro
Memory Display
Manual

23
Initialization procedure 3
Move up or down 3
Set memory positions 1/2/3 4
Keep pressing memory position 1/2/3 4
One key to transfer the memory position 1/2/3 4
The function of position saved with one-key move up and down switch 5
Top or bottom stroke limit 5-6
Unlock the stroke 6
Toggle the display unit format 6
Verify the display switch data to table height 7
The function of position saved with one 8
Error code 9
Contents
STEP 1
›Press and hold & simultaneously for more than 3 seconds.
Legs begin to move down at half speed of normal operation.
STEP 2
›Keep pressing & .
Legs move down to the lowest position and rebound 2-5 mm, then stop.
STEP 3
›Release & together.
Initialization is completed.
STEP 1:
›Touch and hold .
Legs move up.
STEP 2:
›Touch and hold .
Legs stop.

or parts replaced.
2) If the initialization process is interrupted, the system will stop running and will need to be
reinitialized to operate again.
Initialization procedure
Move up & down
Up Key Down Key S KeyScreen
Attention
STEP 3:
›Touch and hold .
Legs move down.
STEP 4:
›Touch and hold .
Legs stop.

45
STEP 1:
›Press and hold or and then release.
Run the legs to the position you want the table-top to be.
STEP 2:
›Click button and then click button , or within next 3 seconds.
Position 1,2 or 3 is saved.
STEP 1
›Press and hold the button , or .
Legs return to the corresponding position saved.
STEP 1
›Quickly click button , or .
Legs return to the corresponding position saved.
1) Memory location elimination after initialization.
2) Memory can be recovered.
Set memory positions 1/2/3
Keep pressing memory position 1/2/3
One key to transfer the memory position 1/2/3
STEP 1:
›Touch and hold button for more than 10 seconds.

STEP 2:
›Release button , touch button within 3 seconds.
!"#$
STEP 3:
›Touch and 
%&#$&#
STEP 4:
›Touch and hold button for 2 seconds.
%!"#$'
STEP 1:
›Press and hold or , then release.
Run the legs to the position you want the table-top to be.
STEP 2:
›Press and hold button , then press and hold for about 3 seconds.
((
the table can be moved to.
STEP 3:
›Release buttons.
Completed.
!"
The function of position saved with one-key move up and down switch
Top or bottom stroke limit (Lock the top stroke limit)
Attention
Attention

67
STEP 1:
›Press and hold or , then release.
Run the legs to the position you want the table-top to be.
STEP 2:
›Press and hold button , then press and hold for about 3 seconds.
((
be moved to.
STEP 3
›Release buttons.
Completed.
STEP 1:
›Press and hold button , then press and hold , keep for about 3 seconds.
()*!#
STEP 2:
›Release the buttons.
Completed.
1) Legs aren't able to run below the locked position.
2) Memory position(s) are/is above the locked position will be lost even after the table is
unlocked, you need to follow Set memory positions again to reset these memory positions.
3) Initialize switch will not unlock the bottom limit.
Top or bottom stroke limit (Lock the bottom stroke limit)
Unlock the stroke
STEP 1:
›Press and hold button , then press and hold , for about 3 seconds.
The height information will be changed between centimeters and inches.
STEP 2:
›Release the buttons.
Completed.
STEP 1:
›Set the table at any height, recommended at the bottom position.
Measure the table actual height and write down the number in inches or in centimeters.
STEP 2:
›Press and hold button , then press and hold for about 3 seconds.
'
STEP 3:
›Release the buttons, then click or 
''
STEP 4:
›Click button .

STEP 5:
›Click or to change the number.
The second number is being increased or decreased to the second number you measured.
STEP 6:
›Click button .

STEP 7:
›Click or to change the number.
The third number is being increased or decreased to the third number you measured.
STEP 8:
›Click button .
Completed.
1) In inch format, the minimum height variation as the legs move up and down is 0.5 inches,
while in centimeter format is 1 centimeter.
Toggle the display unit format
Verify the display switch data to table height
Attention
Attention
1) Check the switch display format in inches or in centimeters and toggle to the unit you like
and match to the actual measurement. In inch format, the minimum adjustable height is 0.5
inches, while in centimeter format is 1 centimeter.
Attention

89
STEP 1:
›Touch and hold button for more than 10 seconds.

STEP 2:
›Release button , touch button within 3 seconds.
!"#$
STEP 3:
›Touch or to change the current clamp force sensitivity level.
+!!##'!!#
!/046(!6!
STEP 4:
›Touch button for 2 seconds.
Completed.
The function of position saved with one-key move up and down switch
Error Code Error Reason Decision Criteria Troubleshooting Solution
E01 Leg
Malfunction
The leg is disconnected from
the control box, screen
displays E01.
1. Legs loosed to the control box, check the cable
connection.
2. Inner parts of legs are broken, replace the legs.
E03 Table-top
overload
The table top load exceeds
the control box's rated load,
screen displays E03.
1. Too many loads on the table-top, remove the
loads.
E04 Control box
malfunction
Control box malfunction,
screen displays E04.
1. Under extreme environment, operating will
cause the control box malfunction, initial proce-
dure needed.
2. Discontinue the initialize process will cause the
control box malfunction,reinitialize needed.
E05 Button of
switch stuck
The handset lasted 30
seconds, and the key value
was unchanged.
Screen displays E05.
1. Button of switch stuck, check the status of the
button, if stuck then toggle the button to restore.
2. Replace the switch.
E06 Communication
disconnected
The handset has been unable
to receive data for 5s, screen
displays E06.
1. Disconnection between switch and control box,
ensure the connection correctly.
2. Check the control box warranty.
E07 Lower setting of
switch verifying
height
The setting height of the
handset is lower than 0,
screen displays E07.
1. Switch setting height is low, the height value is
below 0, needs to adjust the height, lift the table.
E08 Motor short
circuit
Motor cable damaged result-
ing in short circuit, screen
displays E08.
1. Check whether the motor cable is damaged, and
replace the motor cable if necessary.
2. Power on again. If the fault does not disappear,
check whether the motor is working properly.
E09 HALL error HALL count error, screen
displays E09.
1. Reinitialization can be used normally.
E10 Actuator error The actuator part of control
box failure, screen displays
E10.
1. Disconnect the power supply to cool the control
box for 1 minute and the re power it. Replace the
control box if the fault does not disappear.
Error code
Witteveen Projectinrichting
Ouderkerk a/d Amstel
Tel: 020 - 496 5030
[email protected]
www.staand-werken.nl
www.project-inrichting.nl