Markers FT160-19-DLUX Operator's manual

File: Flex Fence instr pg1 of 2 (2018)
For easier installation, pockets are located every
3 inches to secure the fence to each support pole.
YOU MAY ALSO NEED THE FOLLOWING TOOLS:
Tape Measure • String • Chalk or Spray Paint • Mallet or Drill • Sharp Scissors (if cutting is required)
A - Lay out fence line
Using tape measure lay out the radius. Chalk
or paint the line where fence will be installed.
FlexTension Fence Kit #FT160-19 includes:
160 ft Pocket Net Fence, 5 Stabilizing Poles,
14 Flex Poles, Installation Accessories
FlexTension Fence Kit #FT160-19-DLUX includes:
160 ft Pocket Net Fence, 5 Stabilizing Poles, 14 Flex Poles,
Installation Accessories, 19 Ground Sockets
featuring Pocket-Net
TM
Technology
Outfield Fence
NEW
2 Set Pole Layout
160 ft., 19 poles (8.5 ft spacing)
Use 5 reinforced poles as shown ( )
1 Set Pole Layout
100 ft. to Home Plate
Foul Line Foul Line
This can be a 2 ft.
gateway if desired
Set 1
Set 1
Set 2
Set 2
Set 3
Foul Line Foul Line
B - Mark pole locations
Starting at foul line, mark 19 pole locations approx. 8.5 ft. apart
for each 160 ft. set.
Note: If using multiple sets, mark end locations close together
between each set. You can allow for openings 2 ft. wide between sets
for a gateway, or keep them close for a fence with no gateway.
(see 3 diagrams below)
314 linear ft.
2 sets
157 linear ft.
1 set
471 linear ft.
3 sets
100 ft 200 ft. 300 ft.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
320 ft., 38 poles (8.5 ft spacing)
Use 10 reinforced poles as shown ( )
200 ft. to Home Plate
3 Set Pole Layout
These can be (2) 2 ft.
gateways if desired
Foul Line Foul Line
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
300 ft. to Home Plate
480 ft., 57 poles (8.5 ft spacing)
Use 15 reinforced poles as shown ( )
Suggested positions when installing 2 or more fence rolls (L-R)
A - Continuous run - set end poles side by side or tight overlap
B - Overlap gate - pass-thru.
First set 2nd Set
First set
First set
2nd Set
2nd Set
2 ft opening
(OVER)
repeat as needed
for 3rd set
Hint:
For Faster Work,
Drill Pilot Hole using our
optional Auger - 1" dia.
x10"deep.
ALWAYS Make
Pilot Holes
Drive Pilot Hole
Tool into ground
with hammer or
rubber mallet.
Gently tap
Pilot HoleTool
from right to left
to loosen &
remove from
ground.
Use the supplied Socket
Setter and drive Ground
Socket into the ground.
Socket
Setter
Insert fence
Pole into socket
Pilot
Hole
Make sure
the Socket is
flush with the
turf line.
Push Socket as far as
you can into ground.
Installing
Fence Poles
directly
into pilot
hole
Pilot Hole
Use
Rubber Mallet
on posts!
Ground Sockets
Installing Poles / Ground Sockets
1-800-969-5920www.markersinc.com[email protected]

Stretch the material to the next post, locate the nearest pocket and repeat
Steps A-B for all posts.
Raise the fence open pocket and slide the material approximately 12
inches over the post and cap combination. (Remaining material can be
loosely draped over for now.)
Installing your Pocket-Net
TM
fencing is this easy!
Start at foul line
After all Pocket Poles are installed...
It’s easy to replace damaged Pocket Net
TM
Fence
PULL TIGHT to next pocket PULL TIGHT to next pocket
Ground Level
Install 12” of fencing
for remaining
poles
Once you have successfully attached all of the required pockets, the material can be pulled down to
the bottom end of each post. For best appearance, confirm that the fence is tightly stretched between
each post and does not sag. Any excess fencing can be easily cut with sharp scissors.
Find the first opening or “post pocket” by running your hand along the bottom edge of the
fence material; pull pocket open.
File: Pocket Net Fence instr pg2 of 2 (2018)
Gathering material 12” at the top of each pole will make it easier to stretch the material to
the next one in line.
Proceed one pole at a time until
entire roll looks like this
(excess fence is hanging down).
It’s as easy as pulling on socks!
Contact a Markers, Inc. representative, call 1-800-969-5920, Email: [email protected]
Visit us at www.markersinc.com
repeat this for each set
now you’re ready to play!
damaged
fencing?
Create a new section with 2
poles and additional fencing.
Overhead view
cut out damaged fence
New section added
Larger new section added - replacing longer damaged sections
EXISTING POLES
NEW POLE NEW POLE
STABILIZING POLES
119
15
5
10
1-800-969-5920www.markersinc.com[email protected]