EZ Privacy Gate Kit User manual
EZ Privacy Gate Kit Assembly Instructions
Vinyl Fencing Made Easy
www.ezfencecenter.com
Made
in the
USA
Cut to Size
Pocket Rail & T&G Pickets
Sold Seperately
• 4 Upright Metal Support
• 4 Pocket Rail Metal
Support
• 1 PVC Glue
• 2 Post Flat Caps
• 2 Upright Post
• 1½" & ¾" Pan Metal
Sheet Screws & Vinyl Caps
• Gate Lock & Hinges
EZ Privacy Gate Kit
Cut to Size Pocket Rail and T&G Pickets
Not Included
PLEASE READ INSTRUCTIONS BEFORE ASSEMBLY
During assembly, vinyl components should be laid on a non-abrasive surface (i.e. cardboard or drop cloth) so as not to scratch.
• Use care when applying PVC cement, as it
dries quickly. Vinyl should be cleaned with
a mild detergent and non-abrasive cleaning
pad or sponge.
• Gates should not be made any wider than
48", to avoid sagging from hinge post.
TOOLS NEEDED
• Measuring Tape / Ruler
• Pencil
• Screw Driver (Phillips #2)
•
• Drop Cloth
• Square Level
• Rubber Mallet
• Vinyl components should be assembled
without using excessive force, to avoid
breakage.
• All hinge posts properly installed should have
concrete.
•
accurately locate hinge and latch post and
proper width size.
•
distance between hinge and latch post.
For Example: If the gate opening is 44" cut
Top Uprights Post
Step 7 Post Flat Caps Installaon
Flat Cap
USP © 2015
Put a small amount of Vinyl Glue on all sides of the Post Flat Cap and gently tap the Post Flat Cap into the top of
EZ Privacy Gate Kit Assembly Instructions
Completed Privacy Gate Kit
Front Side
- all smooth
Back Side
-with screw caps
Vinyl Glue
Flat Cap
Vinyl Glue
Fig. 11
Need Help or Info.
Call us at 1.888.754.6507
Pocket Rail Metal Support
Step 1 Top/Boom Pocket Rail Metal Support Installaon
Step 2 Connecng Pocket Rail into the Uprights Post
(4 Pieces Included)
Insert, all the way in, the Metal Pocket Rail support
into the Uprights Post. (Fig. 2 & 3)
Fig. 1
Pocket Rail
Uprights Post
USP © 2015
EZ Privacy Gate Kit Assembly Instructions
Pocket Rail
Metal Pocket
Rail Support
Uprights Post
Top Pocket Rail
Step 3 Insert the T&G Pickets in between the Top & Boom Pocket Rail (Fig. 4, 5)
Fig. 4
Fig. 3
Fig. 2
Uprights Post
Pocket Rail
T&G Pickets
IMPORTANT: Use a Square Level
Step 6 Secure Uprights Post and the Pocket Rail with 1½" Pan Head Sheet Metal Screws
Drive the Sheet Metal Screw into the
Upright Post in 3 spots (Fig. 9) then cover
the Pan Head Sheet Metal Screw head with
the Vinyl Screw Cap by tapping. (Fig. 10)
Repeat Step 6 on the remaining 3 corner of
the Uprights Post side.
Vinyl Screw Cap
(12 pcs included)
1½" Pan Head
Sheet Metal Screw
(12 pcs included)
Fig. 9
(4 Pieces Included)
Step 5 Top & Boom Uprights Post Metal Support Installaon
Uprights
Metal Support
Corner Lip
Corner Lip
Insert one Uprights Post Metal
Support into the Top Uprights Post
End Corner, make sure the corner
lip of the Uprights Post Metal
Support is facing towards the
Pocket Rail. (Fig. 8)
Using the ¾" Pan Head Metal Sheet Screw supplied, drive the
Fig. 9
USP © 2015
EZ Privacy Gate Kit Assembly Instructions
Fig. 6
Last T&G Must be Cut to Size
Tonque Groove
Last T&G Picket
Tonque Use this
side
Cut to Size
Groove
Step 4 Cut to Size the last T&G Picket
Fig. 8
Fig. 10
3"
¾"
Last T&G Picket
The cut side will be
the end side.
Pocket Rail
Upright Post
T&G Pickets
Upright Post
