Markwort ROTOR TWIN 100006 Quick setup guide

MARKWORT SPORTING GOODS COMPANY
1203 AMBASSADOR BLVD. SAINT LOUIS, MISSOURI 63132 USA
ROTOR TWIN®: Swing Trainer & Hitting Station
Assembly and Use Guidelines
Item #: 100006
Assembly
Use the Hex Key and small open-end wrench (included) to tighten all bolts used to
secure both Base Plate Legs and the Base Plate Post to the Base Plate. For proper use
the Rotor Twin® Base Legs must be ‘weighed down’ during use (Sand Bags with
separate liners are included –sand is not included).
Warning: The Rotor Twin® is not a toy and requires the use of a bat to be used
properly as a hitting station. Appropriate care should be taken to assemble and set
up the Rotor Twin® hitting station correctly so as to not cause undue wear and tear
to the Rotor Twin® and to ensure the safety of the persons using and around the
Rotor Twin® hitting station.
1. Attach base legs to base plate by lining up the
two holes of each leg with the holes at each end of
the base plate. Place one of the long bolts and a flat
washer through one of the holes on the end of the
base plate and screw into the appropriate hole in one
of the base legs. Repeat procedure to insert
remaining three bolts (two bolts per leg). Tighten.
2. Attach base plate post to base plate by removing
height adjustment lever and sliding the post up through the bottom of
the base plate until its base is snug against the underside of the base
plate. Place a flat washer on each of the short bolts and insert them
through the top of the base plate and through the corresponding holes
in the base plate post. Attach the lock nuts to each bolt and use the Hex
Key and open-end wrench to tighten.
3. Place the height adjustment lever into place on top of the base
plate post. Notice the adjustment screw that is used to adjust (by hand
only) the tension to hold rotor post at desired height. In order for the
Height Adjustment Lever to fit properly it must be right-side-up (see
engraved text on the Height Adjustment Lever).

MARKWORT SPORTING GOODS COMPANY
1203 AMBASSADOR BLVD. SAINT LOUIS, MISSOURI 63132 USA
4. Place the plastic bushing into the top of the base plate post.
5. Connect Rotor Connector Arms w/Baseballs to Rotor Post by
depressing spring buttons on the Rotor Post and inserting into the Rotor
Connector Arms w/Baseballs. Align the spring buttons with the holes in the
Rotor Connector Arms w/Baseballs so that they ‘pop through’ and secure.
6. Slide the above Rotor assembly (with balls) onto the rotor post
(Never put the Rotor Post into the Base Plate Post without the Plastic
Bushing in place). TRICKY PART: With Rotor assembly (with balls)
fitted into the Rotor Post, first tighten the Height Adjustment Lever by
hand, holding the bolt in place while tightening the lever until the
Rotor Post begins to ‘grab’ the Rotor Assembly (with balls). Once the
Rotor Assembly remains in place without assistance, close the lever
on the Height Adjustment lever (see engraved text for ‘open’ and
‘closed’ positions), to firmly secure the Rotor Assembly at the desired
height. Note that if the lever cannot be closed, or if the lever is closed but the Rotor
Assembly height can still be adjusted by hand, open the lever and loosen or tighten the
Height Adjustment Lever by hand (see above), fine tuning until the Height Adjustment
Lever can be fully closed around the Rotor Assembly.
7. Fill each of the 4 plastic bag liners to the desired level with sand and “Zip” the liners
closed. Then slide filled liners into the canvas sandbags. Close the sandbags. When closing
the plastic liners squeeze out as much air as possible as you seal the liners. Secure the
sandbags to the base plate legs by sliding a leg into the slot at the top of each bag. The
Velcro ties should be on the outside and should be tied securely.
Use and Care
1. Always hit parallel to base plate with legs pointing to and away from hitter.
2. Store the Rotor Twin in a dry place. Leaving it outside in the rain or sub-freezing
temperatures will add unnecessary wear and tear to the unit.
4. Periodically check the screws and bolts and retighten as necessary.
5. Train hard and have Fun!
Parts Included with the Rotor Twin®
BAP16 Bolt/Accessory Pack (16Pcs)
BALLARM Baseballs & Connector Arm (1ea)
HAL Height Adjustment Lever (1ea)
RP Rotor Post (1ea)
BPL Base Plate Legs (2ea)
SB Set of Four Sandbags (4ea)
SBL Set of Four Sandbag Liners (4ea)
PRB Plastic Bushing (1ea)