SPALDING E6A994 User manual

109/21 ID# M6A40201
© COPYRIGHT 2021 by Russel Brands, LLC
Portable Basketball System
Owners Manual
READ AND UNDERSTAND
OPERATOR’S MANUAL BEFORE
USING THIS UNIT.
FAILURE TO FOLLOW OPERATING
INSTRUCTIONS COULD RESULT IN
INJURY OR DAMAGE TO PROPERTY.
WARNING!
Write Model Number From Box Here:
This manual, accompanied by sales receipt,
should be saved and kept on hand as a
convenient reference, as it contains important
information about your model.
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1300 367 582
English
Español

2
IMPORTANT!
Adult Assembly Required
Dispose of ALL packaging materials promptly.
As with all products, periodically inspect for loose small parts.
Assembled unit MUST be filled with sand or water at ALL times.
ALL basketball systems, including those used for DISPLAYS, MUST be
assembled and installed according to instructions.
Failure to follow instructions could result in SERIOUS INJURY.
It is NOT acceptable to devise a makeshift support system.
BEFORE YOU START
REMOVE ALL CONTENTS!
Remove ALL contents from boxes.
Be sure to check INSIDE pole sections;
hardware and additional parts are packed inside.
OR
NOTICE TO ASSEMBLERS
Email: [email protected]
Spalding
PO Box 90015
Bowling Green, KY 42103-7932

3
EXACTA-HEIGHT : ADJUSTMENT
PORTABLE
511679
Size = 4" x 5.5"
Corner Radius = 3/8"
Die Cut Label
3.25 Mil Vinyl
All Temp. Permanent Adhesive
1 Mil. Polypropolyne Overlaminate
Illustrator 8.0 = EPS
Backing + 1/16 Circumference
Rolls of 500
2
2
1
3
TO ADJUST BACKBOARD:
1. While holding handle, remove pin.
2. Move elevator up or down to
desired height.
3. Replace pin full length to lock
system at desired height.
511679 05/05
1
2
4
3
MOVING SYSTEM
Adjust basketball backboard
height to lowest position.
While holding pole, rotate
basketball system forward
until wheels engage with
ground.
Move basketball system to
desired location.
Carefully rotate basketball
system upright.
1.
2.
3.
4.
5. Check system for stability.
HEIGHT ADJUSTMENT
REQUIRED TOOLS
AND MATERIALS:
AND/OR
OPTIONAL TOOLS
AND MATERIALS:
1/2” 9/16” 3/4”
• 2 Capable Adults
• Tape Measure
• Wood Board
(scrap)
• Sawhorse or
Support Table
• Hammer/Mallet
• Safety Glasses
• Step Ladder - 8ft.
(2.4 m)
• Phillips-Head
Screwdriver
SAND
300 lb.
(136 kg)
• (2 each) Wrenches and/or Socket
Wrenches and Sockets (Deep-
Well Sockets are Recommended).
• Extension is Recommended.
• Large and Small Adjustable
Wrenches
• Garden Hose or Sand
9/16”
1/2” 3/4”
10-3/4" High
4" Wide
PMS 021 for Warning
Owner must ensure that all players know and follow these rules
for safe operation of the system.
WARNING
• DO NOT hang on the rim or any part of the system including
backboard, support braces, or net.
• During play, especially when performing dunk type activities, use
caution to keep face away from the backboard, rim, and net.
Serious injury could occur if teeth/face come in contact with
backboard, rim, or net.
• DO NOT slide, climb, shake, or play on base and/or pole.
• After full assembly, fill system completely with water or sand.
Never leave system in an upright position without filling base with
weight, as system may tip over, causing injuries and/or property
damage.
• DO NOT add ballast on top of base (such as sand bags or cinder
blocks). Such added ballast can crack base, causing leakage,
which could cause system to tip over. DO NOT use ballast on top
of base as substitute for filling base with water or sand.
• When adjusting height or moving system, keep hands and fingers
away from moving parts.
• DO NOT allow children to move or adjust system.
• DO NOT wear jewelry during play (rings, watches, necklaces, etc.).
Objects may entangle in net.
• Surface beneath the base must be smooth and free of gravel or
other sharp objects. Punctures or cracks in base could result,
causing leakage which could cause system to tip over.
• Keep organic material and water away from pole base. Grass,
water, litter, etc. could cause corrosion and/or deterioration.
• Keep pole top covered with cap at all times. Water and debris
entering pole through uncapped top can cause corrosion from
the inside.
• CHECK pole system for signs of corrosion (rust, pitting, chipping)
and repaint with exterior enamel paint. If rust has penetrated
through the steel anywhere, replace pole immediately.
• CHECK system before each use for proper ballast, loose
hardware, excessive wear, and signs of corrosion; replace or
repair before use.
• CHECK system before each use for instability.
• DO NOT use or leave system upright during windy and/or adverse
weather conditions; system may tip over. Place system in the
storage position and/or in an area protected from the wind and
weather, and free from personal property and/or overhead wires.
• Never play on damaged equipment.
• See instruction manual for proper assembly and maintenance.
• When moving system, use caution to keep height adjust
mechanism from shifting.
• Do not allow water in tank to freeze. During sub-freezing weather
add at least 2 gallons of non-toxic antifreeze or sand, or empty
tank completely and store. (Do not use salt.)
• DO NOT allow anyone to stand or sit on base while moving system.
• DO NOT leave system unsupervised, or play on system when
wheels are engaged for moving.
• Use caution when moving system across uneven surfaces.
System may tip over.
• Use extreme caution if placing system on sloped surface. System
may tip over.
READ AND UNDERSTAND WARNINGS
LISTED BELOW BEFORE USING THIS
PRODUCT.
FAILURE TO FOLLOW THESE WARNINGS
MAY RESULT IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
MUNSELL NOTATION
Hue Value Chroma
5.0 YR 6.0/15
Equiv. CIE Data
(Y%) xy
30.05 0.5510 0.4214
Approx. PMS Color
13 parts yellow
3 parts Warm Red
1/4 part Black
Warning Area = Orange
Corner Radius = 3/8"
Die Cut Label
3.25 Mil Vinyl
All Temp. Permanent Adhesive
1 Mil. Polypropolyne Overlaminate
Illustrator 8.0 = EPS
Backing + 1/16 Circumference
Rolls of 500
ID#: 500082 07/21
Trademarks registered
in the USA and other countries.
In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339
In Australia: 1-300-367-582

4
TEST-FIT CLOSE TOLERANCE BOLTS
To ensure optimal playability of backboard system, a close tolerance fit between the elevator
components and hardware is required.
Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates.
Carefully rock them in a circular motion to ream out any excess paint from holes if necessary.
NOTE: Not all items pictured are included with every model.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully.
Check entire box and inside all packing material for parts and/or additional instruction material. Before
beginning assembly, read the instructions and identify parts using the hardware identifier and parts list
in this document. Proper and complete assembly, use, and supervision are essential for proper operation
and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not
installed, maintained, and operated properly.
• If using a ladder during assembly, use extreme caution.
• Check base regularly for leakage. Slow leaks could cause the system to tip
over unexpectedly
• Seat the pole sections properly (if applicable). Failure to do so could allow
the pole sections to separate during play and/or during transport of the
system.
• Climate, corrosion or misuse could result in system failure.
• If technical assistance is required, contact Customer Service.
• Minimum operational height is 6’-6” (1.98m) to the bottom of backboard.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.

5
For the very latest Basketball System Warranty information
Please visit the Spalding Basketball website at www.Spalding.com
Contact Spalding Customer Service at phone # [phone]
Basketball System
Warranty
Para la última información de garantía del sistema de baloncesto
Por favor visite el sitio web de Spalding Basketball en www.Spalding.com
Póngase en contacto con servicio al cliente de Spalding en teléfono # 1-800-558-5234
Sistema de baloncesto
Garantía de dueños
Die neuesten Basketball System-Garantie informationen
Besuchen Sie bitte die Spalding Basketball-Website unter www.Spalding.com
Spalding-Kundendienst am Telefon # [phone]
Basketball-System
Garantie
Pour l'information de garantie de système de basket-ball plus tard
Visitez le site Web de Spalding Basketball à www.Spalding.com
Contacter le Service clientèle Spalding au # de téléphone 1-800-558-5234
Système de basket-ball
garantie
05/2013
Get to know the basic parts of your basketball system...
BACKBOARD
RIM
BASE
BOTTOM POLE
ELEVATOR SYSTEM
TOP POLE
MIDDLE POLE
WHEEL CARRIAGE
FRONT PANEL

6
PARTS LIST (ALL) - See Hardware Identifier
NOTE
Hardware kit is designed for more
than one style of basketball system.
Not all hardware will be used.
Item Qty. Part No. Description
1 1 600335 Base
2 2 908184 Strut, Pole to Base, Black
3 1 701292 Exacta Height Assembly, Black
4 1 FR908006 Top Pole Section, Black
5 1 901403 Middle Pole Section, Black
6 1 FR908181 Bottom Pole Section, Black
7 2 108183 Wheel Bracket
8 2 266200 Wheel, 4 Inch
9 2 10818201 Rod, Axle
10 1 203099 Nut, Ny-lock, 5/16-18
11 4 203063 Nylon Insert Lock Nut, 3/8-16
12 1 202662 Bolt, Hex Head, 5/16-18 x 4-1/2 Long
13 4 207550 Pushnut, 7/16 Shaft Diameter
14 13 203100 Hex Flange Nut 5/16-18
15 1 801100 Bracket, Pole Mount
16 2 203053 Carriage Bolt, 5/16-18 x 4 Long
17 4 203232 Washer, Flat, 3/4” O.D.
18 2 204962 Bolt, Hex Head, 5/16-18 x .625 Long
19 2 206360 Bolt, Hex Head, 3/8-16 x 2-5/8 Long
20 2 600282 Spacer, Plastic Biscuit
21 2 204857 Spacer, Metal 1/2” O.D. x 1.44 Long
22 2 204859 Cover, Pin Slide
23 1 203038 Carriage Bolt, 5/16-18 x 2-3/4 Long
24 1 204850 Pin, Locking
25 1 204853 Lanyard, Black Coil
26 4 208891 Spacer, .380 I.D. x .67 Long
27 2 208890 Bolt, Hex Head, 3/8-16 x 5.625 Long
28 1 600337N Cover, Front
29 4 206244 Bolt, Hex Head, 1/2-13 x 8 Long
30 4 201642 Spacer, Plastic, .530 I.D. x .625 Long
31 5 206340 Lock Nut, Hex 1/2-13
32 2 901402 Elevator Tube, Lower - Long, Black
33 1 204838 Spring, Counter Balance
Item Qty. Part No. Description
34 1 Rim
35 2 901401 Elevator Tube, Upper - Short, Black
36 2 201682 Spacer, .530 I.D. x 1.875
37 2 900867 Plate, Triangle, Black
38 1 600137 Cap, Pole Top
39 2 200520 Screw, #8 x 3/4 Long
40 1 202605 Bolt, Hex, 1/2-13 x 4.25 Long
41 1 203617 Cap, Base
42 1 206990 Reinforcement Bracket
43 1 Net
44 4 208892 Bolt, Hex Flange, 5/16-18 x 1.625 Long
45 2 203156 Bolt, Hex Head, 5/16-18 x 1” Long
46 1 511679 Label, Height Adjustment and Moving
FR511679 Label, Height Adjustment and Moving,
French
47 6 208505 Carriage Bolt, 5/16-18 x 1.5 Long
48 1 206089 Spacer, Plastic, .530 I.D. x 3.5 Long
49 1 108181 Plate, Pole Mounting
50 2 203679 Bolt, Hex Head, 3/8-16 x 2 Long
51 6 203218 Washer, Flat, 5/16
52 1 200516 Cover, Bolt End, Vinyl
53 1 900033 Bracket, Slam Jam
54 1 206048 Bolt, Tee, 3/8-16, 3.25” Long
55 1 200318 Bracket, Reinforcement, Slam Jam
56 1 208760 Spring, Rim
57 1 203795 Nut, Special, 3/8-16
58 1 203470 Washer, Flat, 1.5 O.D.
59 1 20157801 Board Pad, Left Section
60 1 20157901 Board Pad, Right Section
61 1 201580 Board Pad, Center Section
62 2 201596 Screw, 1/4 x 1.25
63 6 206303 Washer, Flat, 1/4
64 1 200503 Cover, Black OR
200504 Cover, Red
65 4 202871 Screw, 1/4 x .75
66 1 220579 Spacer, Metal, 0.51 ID x 5.0 Long

07/08 ID# M6611742
7
#40 (1)
#39 (2)
Item #23 (1)
#29 (4)
#16 (2)
#12 (1)
#44 (4)
#19 (2)
#47 (6)
#54 (1)
201596 Screw 1/4 x 1.
#62 (2)
#21 (2) #9 (2)
#18 (2)
#50 (2)
HARDWARE IDENTIFIER (ALL BOLTS AND SCREWS) Shown Full Scale
HARDWARE IDENTIFIER (ALL METAL SPACERS) Shown Full Scale
#45 (2)
#27 (2)
208505
202871 - SCREW HEX WASHR HD TAP SLOTTED 1/4 X 3/4
#65 (4)
#66 (1)

8
ID# M6611742 07/08 8
HARDWARE IDENTIFIER (ALL NUTS & WASHERS) Shown Full Scale
HARDWARE IDENTIFIER (ALL OTHER) Not Shown to Scale
HARDWARE IDENTIFIER (ALL PLASTIC SPACERS CAPS & CLIPS) Shown Full Scale
203100
NUT, HEX FLANGE, 5/16-18
#14 (13)
203099Hex Locknut (Nylon Insert) 5/16-18
#10 (1) #11 (4)
#31 (5)
#17 (4) #57 (1)
#58 (1) #51 (6) #63 (6)
#53 (1)
#55 (1)
#56 (1)
#13 (4)
#20 (2)
#30 (4)
#52 (1)
#36 (2)
#48 (1)
#26 (4)

9
TOOLS REQUIRED FOR THIS SECTION
This is what your system will look like
when you’ve finished this section.
1/2” 9/16”
(2) Wrenches AND/OR
Phillips-Head Screwdriver
Hammer/Mallet
(2) Socket Wrenches and Sockets
Extension
1/2” 9/16”
SECTION A: ASSEMBLE THE BASE & POLE

10
Check the following pre-assembled handle areas for tightness:
Screw P/N 204803, Nut P/N 203100, Carriage Bolts P/N 203103.
Carriage Bolt P/N 203103
Nut P/N 203100
Nut P/N 203100
Handle, Right P/N 204856
Handle, Left P/N 204855
Screw P/N 204803
Carriage Bolt P/N 203103
Height Adjustment Rod P/N 901050
Label,Height Indicator P/N 204872
Label,Height Indicator P/N 204872
3
PRE-ASSEMBLED HANDLE

07/08 ID# M6611742
11
WHEEL ASSEMBLY - HARDWARE IDENTIFIER KIT #1 Shown Full Scale
#13 (4)
#9 (2)
PARTS LIST - KIT #1
Item Qty. Part No. Description
7 2 108183 Wheel Bracket
8 2 266200 Wheel, 4 Inch
9 2 10818201 Rod, Axle
13 4 207550 Pushnut, 7/16 Shaft Diameter
18 2 204962 Bolt, Hex Head, 5/16-18 x .625 Long
51 2 203218 Washer, Flat, 5/16
#51 (2)
#18 (2)
#8 (2)
#7 (2)
KIT #1
Not Shown Full Scale

12
1
7
8
9
13
13
Complete wheel assembly as shown in Figure A. Secure wheel bracket (7), wheel (8), axle (9),
and push nuts (13) to the base (1) with a single bolt (18) and washer (51). Repeat procedure for
opposite wheel.
1.
A.
NOTE
Do not install both bolts into the wheel assembly
at this time.
The back bolt will be installed during strut
assembly in Step 3 of this section.
NOTE
Wood Block
TO INSTALL SECOND PUSHNUT:
• Assemble Pushnut, Wheels, Axle, And Wheel
Bracket As Shown.
• Support Pushnut/Axle From The End With A
Block Of Wood To Install The Second Pushnut Onto
The Axle.
18
51
18
51

13
Correctly identify each pole section.
With a marker and tape measure, mark a line 3 1/2” from top end of poles (5 & 6).
2.
4
3 1/2”
(8,9 cm)
STOP AND CALL CUSTOMER SERVICE IF YOU
HAVE ANY QUESTIONS OR NEED ASSISTANCE
REGARDING ASSEMBLING THE POLE SECTIONS
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1300 367 582
TOP POLE MIDDLE POLE BOTTOM POLE
3 1/2”
(8,9 cm)
5 6
Marked Line
Marked Line

14
4
5
MIDDLE POLE
TOP POLE
While maintaining alignment of dimple and trough, bounce middle pole section (5) into top pole
section (4) using a wood scrap as shown until the top pole (4) is aligned with the marked line on
the middle pole (5).
You should have a 3 1/2” (8,9 cm) of overlap when properly assembled.
3.
MARKED LINE
TROUGH
DIMPLE
5
MIDDLE POLE
4
TOP POLE
HOLE
(NOT USED
IN ASSEMBLY)
IMPORTANT!
Align dimple of top pole section (4) into trough
of middle pole section (5) as shown.
MARK LINE
3 1/2”
(8,9 cm)
CAUTION!
WHEN PROPERLY POUNDED
TOGETHER, THE POLE SECTIONS
SHOULD HAVE A 3-1/2” (8,9 CM)
OVERLAP.
Wood Scrap
(not supplied)

15
4. While maintaining alignment of dimple and trough, bounce top and middle pole
assembly (4 and 5) onto bottom pole section (6) using a wood scrap as shown.
Bounce until the top and middle pole assembly (4 and 5) is aligned with the
marked line on the bottom pole (6).
You should have a 3 1/2” (8,9 cm) of overlap when properly assembled.
5
4
6
MARKED LINE
6
MIDDLE POLE 5
HOLE
(NOT USED
IN ASSEMBLY)
IMPORTANT!
Align dimple of middle pole section (5) into
trough of bottom pole section (6) as shown. MIDDLE POLE
TOP POLE
BOTTOM POLE
BOTTOM POLE
MARK LINE
3 1/2”
(8,9 cm)
CAUTION!
WHEN PROPERLY POUNDED
TOGETHER, THE POLE SECTIONS
SHOULD HAVE A 3-1/2” (8,9 CM)
OVERLAP.
Wood Scrap
(not supplied)
DIMPLE
TROUGH

16
ID# M6611742 07/08
POLE TO BASE ASSEMBLY - HARDWARE IDENTIFIER KIT #2 Shown Full Scale
PARTS LIST - KIT #2
Item Qty. Part No. Description
10 1 203099 Nut, Ny-lock, 5/16-18
12 1 202662 Bolt, Hex Head, 5/16-18 x 4-1/2 Long
14 6 203100 Hex Flange Nut 5/16-18
45 2 203156 Bolt, Hex Head, 5/16-18 x 1” Long
47 6 208505 Carriage Bolt, 5/16-18 x 1.5” Long
49 1 108181 Plate, Pole Mounting
50 2 203679 Bolt, Hex Head, 3/8-16 x 2 Long
51 4 203218 Washer, Flat, 5/16
52 1 200516 Cover, Bolt End, Vinyl
#51 (4)
203099Hex Locknut (Nylon Insert) 5/16-18
#10 (1)
#52 (1)
#45 (2)
#50 (2)
#49 (1)
#12 (1)
203100
NUT, HEX FLANGE, 5/16-18
#14 (6)
#47 (6)
KIT #2
208505

17
5. Attach pole assembly to base (1) as shown.
Secure pole assembly to base using bolts (50) and pole mounting bracket (49) as shown.
6
49
6
1
50
50
WARNING!
TWO PEOPLE REQUIRED FOR THIS
PROCEDURE. FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
6. Secure base struts (2) to pole as shown.
Place cover (52) over exposed end of bolt as shown.
12
52
10
51
51
2
2
IMPORTANT!
DO NOT TIGHTEN
COMPLETELY
49

18
7. Rotate non-secured ends of base struts (2) outward to mounting holes in base as shown.
Secure ends of base struts (2) to wheel bracket (7), as shown. Repeat for opposite side.
1
45
2
2
51 45
51
IMPORTANT!
DO NOT TIGHTEN
COMPLETELY
8. Secure cover (28) to base struts (2) using bolts (47) and nuts (14) as shown.
14
47
28
2
14
14
47
47
IMPORTANT!
TIGHTEN ALL COMPONENTS
COMPLETELY (STEPS 6-8).
45
51

19
#15 (1)
#42 (1)
#24 (1) #25 (1)
#22 (2)
ELEVATOR ASSEMBLY - HARDWARE IDENTIFIER KIT #3 Shown Full Scale
KIT #3
ELEVATOR ASSEMBLY PARTS LIST - KIT #3
Item Qty. Part No. Description
11 2 203063 Nylon Insert Lock Nut, 3/8-16
14 3 203100 Hex Flange Nut 5/16-18
15 1 801100 Bracket, Pole Mount
16 2 203053 Carriage Bolt, 5/16-18 x 4 Long
17 4 203232 Washer, Flat, 3/4” O.D.
19 2 206360 Bolt, Hex Head, 3/8-16 x 2-5/8 Long
ItemQty.Part No.Description
20 2 600282 Spacer, Plastic Biscuit
21 2 204857 Spacer, Metal 1/2” O.D.x 1.44 Long
22 2 204859 Cover, Pin Slide
23 1 203038 Carriage Bolt, 5/16-18 x 2-3/4 Long
24 1 204850 Pin, Locking
25 1 204853 Lanyard, Black Coil
42 1 206990 Reinforcement Bracket
#19 (2)
#16 (2)
203100
NUT, HEX FLANGE, 5/16-18
#14 (3)
#20 (2)
#17 (4)
#11 (2)
Item #23 (1)
#21 (2)
Not Shown Full Scale

Attach spacers (20, 21) to pole mount bracket (15) with
bolts (19), washers (17), and nuts (11) as shown.
Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts (16) to top pole
(4) as shown. Tighten flange nuts (14) completely.
4
42
16
16
15
14
14
20
9.
10.
15
17
17
11
19
17
17
21
20
20
21
IMPORTANT!
Tighten just until washers
(17) stop moving.
IMPORTANT!
DO NOT OVER TIGHTEN.
TOP POLE
4