MEP840H-24/16 & MEP841H-24/16 MEP840H-24/16 & MEP841H-24/16
SEIRES SEIRES
3” 4 BOLT TYPE A FLANGE 3” 4 BOLT TYPE A FLANGE
X 2” 90 DEGREE ELBOW KIT X 2” 90 DEGREE ELBOW KIT
The contents of this publication are for informational purposes only. While every The contents of this publication are for informational purposes only. While every
effort has been made to ensure accuracy, these contents are not to be construed as effort has been made to ensure accuracy, these contents are not to be construed as
warranties or guarantees, expressed or implied, regarding the products or services warranties or guarantees, expressed or implied, regarding the products or services
described herein or for their uses or applicability. Marshall Exclesior Co. services described herein or for their uses or applicability. Marshall Exclesior Co.
reserves the right to modify or improve the designs or specifications of such reserves the right to modify or improve the designs or specifications of such
products at any time without notice. The MECTM logo is the trademark of products at any time without notice. The MECTM logo is the trademark of
Marshall Excelsior Co. Marshall Excelsior Co.
Form #1161 Rev A 11/14/18 Form # Rev A 11/14/18
!!! WARNING !!!
Failure to follow these instructions or to properly install and
maintain this equipment could result in an explosion and/or fire
causing property damage and personal injury or death.
Install, operate and maintain Marshall Excelsior Co. equipment in
accordance with federal, state, and local codes and these instructions.
The installation in most states must also comply with NFPA #58,
ANSI K61.1 and DOT standards.
Only personnel trained in the proper procedures, codes, standards,
and regulations of the LP Gas or anhydrous ammonia (NH3)
industries should install and service this equipment.
WARNING: These products contain a chemical known to
the state of California to cause cancer and birth defects or
reproductive harm
!!! CAUTION !!!
Always wear suitable eye protection, gloves and protective clothing
when operating or servicing LPG and NH3 equipment.
Check seals, seats and threads for wear and damage before use. Repair
or replace all defective parts immediately.
Always completely relieve system or line pressure prior to servicing
equipment and plumbing.
Regular inspection and maintenance is essential for continued safe
operation.
Introduction
Scope of the Manual
This manual covers instructions for the 2” 90 Degree x 3” 4 Bolt
Type A Flange Kit. This kit allows for the connection of a pump
auxiliary inlet to a 2” connections
Description
The 2” 90 Degree x 3” 4 Bolt Type A Flange is designed to
connect to larger pressure sources, such as the opening of a pump,
and reduce the piping size from a 3” connection down to a 2”
connection.
!!! WARNING !!!
Release all downstream pressure before removing any bolts, panels,
etc. from the system. Failure to follow these instructions or properly
install and maintain this equipment could result in an explosion
and/or fire causing property damage and personal injury or death.
!!! WARNING !!!
Failure to follow these instructions or to properly install and
maintain this equipment could result in an explosion and/or fire
causing property damage and personal injury or death.
Install, operate and maintain Marshall Excelsior Co. equipment in
accordance with federal, state, and local codes and these instructions.
The installation in most states must also comply with NFPA #58,
ANSI K61.1 and DOT standards.
Only personnel trained in the proper procedures, codes, standards,
and regulations of the LP Gas or anhydrous ammonia (NH3)
industries should install and service this equipment.
WARNING: These products contain a chemical known to
the state of California to cause cancer and birth defects or
reproductive harm
!!! CAUTION !!!
Always wear suitable eye protection, gloves and protective clothing
when operating or servicing LPG and NH3 equipment.
Check seals, seats and threads for wear and damage before use. Repair
or replace all defective parts immediately.
Always completely relieve system or line pressure prior to servicing
equipment and plumbing.
Regular inspection and maintenance is essential for continued safe
operation.
Introduction
Scope of the Manual
This manual covers instructions for the 2” 90 Degree x 3” 4 Bolt
Type A Flange Kit. This kit allows for the connection of a pump
auxiliary inlet to a 2” connections
Description
The 2” 90 Degree x 3” 4 Bolt Type A Flange is designed to
connect to larger pressure sources, such as the opening of a pump,
and reduce the piping size from a 3” connection down to a 2”
connection.
!!! WARNING !!!
Release all downstream pressure before removing any bolts, panels,
etc. from the system. Failure to follow these instructions or properly
install and maintain this equipment could result in an explosion
and/or fire causing property damage and personal injury or death.
