Martin Magnum 2500Hz User manual

Magnum 2500Hz
user manual
P/N 35010030G
READ AND SAVE THESE INSTRUCTIONS

2
Dimensions/Legal
Dimensions/Legal
All dimensions are in millimeters
Information subject to change without notice. HARMAN Professional Denmark ApS disclaims liability for any injury,
damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to
use or reliance on the information contained in this document.
©2016 HARMAN Professional Denmark ApS. All rights reserved. Martin®and JEM™ are registered trademarks of
HARMAN Professional Denmark ApS registered in the United States and/or other countries. Features, specifications,
and appearance are subject to change without notice.
HARMAN Professional Denmark ApS • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark
www.martin.com
Document Revision - G

3
Contents
Contents
Dimensions/Legal...................................................................................................................... 2
Contents .................................................................................................................................... 3
Safety information...................................................................................................................... 4
Product overview....................................................................................................................... 7
Product description................................................................................................................ 7
Features at a glance .............................................................................................................. 7
Product details ....................................................................................................................... 8
Quick Start................................................................................................................................. 9
Setting up............................................................................................................................... 9
Making haze........................................................................................................................... 9
Installation and setting up........................................................................................................ 10
Location................................................................................................................................ 10
AC power ............................................................................................................................. 10
Setting up............................................................................................................................. 11
Final checks......................................................................................................................... 12
Turning on the power........................................................................................................... 12
Control settings........................................................................................................................ 13
Overview.............................................................................................................................. 13
Continuous Run Mode......................................................................................................... 13
Setting the Automatic Timer................................................................................................. 13
Setting the “one-shot” timer ................................................................................................. 14
Priming the Machine ............................................................................................................ 15
What the status lights mean................................................................................................. 16
DMX control............................................................................................................................. 17
Overview.............................................................................................................................. 17
Connection........................................................................................................................... 17
DMX functions...................................................................................................................... 17
Setting the DMX start address............................................................................................. 18
Approved Haze Fluid Types.................................................................................................... 19
Approved Discontinued Fluids:............................................................................................ 19
Basic service............................................................................................................................ 20
Cleaning............................................................................................................................... 20
Martin Pro Clean and Storage Fluid..................................................................................... 20
Fuse replacement ................................................................................................................ 21
Shutting down the machine..................................................................................................... 22
Shutdown procedure............................................................................................................ 22
Optional accessories ............................................................................................................... 23
Fitting the DMX module ....................................................................................................... 23
Troubleshooting....................................................................................................................... 24
Technical Specifications.......................................................................................................... 25
Notes ....................................................................................................................................... 28

4
Safety information
Safety information
Read the safety precautions in this manual before installing, operating or
servicing this product.
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
severe injury or
death.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due to
electric shock, burns, falls and respiratory problems!
Read this manual before operating the machine, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the
machine. Use the machine only as described in this manual and in accordance
with local laws and regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Martin Service and Support.
Preventing electric shocks
Always ground (earth) the machine electrically.
Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.
Before connecting the machine to power, check that the voltage
indicated on the machine’s serial label matches your local AC power
voltage. If your AC power voltage does not match, do not use the
machine. Contact Martin Service and Support for assistance.
Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.
If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine and
contact Martin Service and Support for assistance. If the supply cord is
damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.
Disconnect the machine from AC power before servicing and when not in
use.
This machine is not waterproof and should not be exposed to wet
outdoor conditions. Do not immerse in water or any other liquid. Do not
expose to high-pressure water jets.

5
Safety information
Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the machine out of service and contact Martin Service and
Support for advice.
Do not remove the covers or attempt to repair a faulty machine. Refer
any service not described in this manual to Martin Service and Support.
Do not operate the machine if any parts are damaged, defective or
missing.
Moisture and electricity do not mix. Do not aim haze output at electrical
connections or devices.
Preventing burns and fire
The haze produced by the machine is hot enough to cause burns when it
leaves the nozzle, and very hot droplets of fluid escape occasionally.
Keep people and objects at least 600 mm (24 in.) away from the haze
output nozzle.
Do not touch the haze output nozzle during or after use –it becomes
extremely hot and remains hot for several hours after the machine has
been shut down.
Haze output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point haze output at sources of
ignition such as open flames or pyrotechnic effects.
Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
Replace fuses only with ones of the type and rating specified in this
manual for the machine.
Provide a minimum free space of 100 mm (4 in.) around the machine.
Provide a minimum free space of 500 mm (20 in.) around fans and air
vents and ensure free and unobstructed airflow to and around the
machine.
Keep the machine at least 600 mm (24 in.) away from combustible and
heat-sensitive materials.
Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).
Do not operate the machine if the relative air humidity exceeds 80%.
Preventing injuries
Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.
Do not install the machine over areas where people are present.
Do not operate the machine with missing or damaged covers or shields.
In the event of an operating problem, stop using the machine
immediately and disconnect it from power. Do not attempt to use a
machine that is obviously damaged.
Do not modify the machine in any way not described in this manual or
install other than genuine Martin parts.
Refer any service operation not described in this manual to a qualified
technician.
Haze output can cause condensation. Do not point the output at smooth
floors. Floors and surfaces may become slippery. Check these frequently
and wipe dry as necessary to avoid any danger of slipping.
Ensure at least 2 m (6.6 ft.) visibility in areas where haze is being
produced.

6
Safety information
Haze fluid contains food-grade glycols in solution that may present
health risks.
IF SWALLOWED: Do not induce vomiting. Drink 1-2 glasses of water
and seek medical attention.
AVOID CONTACT WITH SKIN AND EYES: In case of accidental
contact: EYES: Hold eyes open and flush with water for ten minutes,
seek medical attention if irritation persists. SKIN: Remove contaminated
clothing and rinse skin for 20 minutes, seek medical attention if irritation
persists.
Consult the fluids' SDS for more detailed safety information at
http://www.martin.com/safety-documents
This machine is not intended for use by persons (including children) with
reduced physical sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the machine by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
machine.
Preventing breathing problems
A haze machine can operate safely only with the haze fluid it is designed
for. Use the machine only with fluids specified under “Approved Haze
Fluid Types” on page 19 or you may cause the release of toxic gases,
presenting a severe health hazard. You will also probably damage the
machine.
Do not create dense haze in confined or poorly ventilated areas.
Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to haze output.
Do not point haze output directly at a person’s face or at face height.
For the latest user documentation and other information for this and all Martin
products, please visit the Martin website at http://www.martin.com
If you have any questions about how to install, operate or service the fixture
safely, please contact your Martin distributor, dealer or contact Martin Service
and Support.

7
Product overview
Product overview
Product description
The Magnum 2500Hz from Martin provides a uniquely flexible and convenient
solution to a wide range of atmospheric requirements whether permanently
installed or taken on the road.
The machine features a unique new design that encompasses what the Magnum
range is all about: state of the art technology, high quality and ruggedness.
Congratulations on your purchase of the Magnum 2500Hz from Martin. Details of
the full range of Martin products are available on our website at www.martin.com.
Features at a glance
Proportional haze & fan output
Continuous effect output
Timer remote control included
Output and density level control
Internal remote control storage
Concealed 3.8 l fluid reservoir
Fluid-out sensing
Uses economical RUSH & THRILL Haze Fluid
Optional DMX interface
Machine link mode - up to 4 units can be operated at the same time with one
remote.

8
Product overview
Product details
Haze output nozzle
Fluid level sight gauge
Warning!
High temperature vapour
and surfaces!
Concealed 3.8 l fluid reservoir
DMX start address
DIP switches
Remote /
machine link
sockets
Mains power switch
Mains power inlet
DMX in/out jacks
Status Indicators
Heat (Red)
Ready (Green)

9
Quick Start
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot of
haze. This section tells you how to do that. However, please also make the time
to read the safety and servicing instructions in the remainder of this manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the haze
output.
Fill the fluid reservoir with Martin approved haze fluid (see page 19). The fluid
compartment is opened by pulling outwards on the cover (pull using a finger in
the round hole).
Connect the machine to a suitably rated power source. The power requirements
are:
EU Models –920 W, 220-240 V
US Models –920 W, 100-130 V
Connect the remote control to the REMOTE IN connector on the rear panel.
Turn on the power switch. The red Heat indicator on the remote and the rear of
the unit will light. After about 6-8 minutes the green Ready indicator on the
remote and the rear of the unit will light. The machine is then ready to produce
haze. To obtain maximum haze output, wait another couple of minutes for the
Heat indicator to go out.
Making haze
Once the machine has heated up, press the FOG button on the remote to start
the haze output. The green ON light will come on. Press the FOG button again to
turn off the haze.
You can set the haze density by turning the knob. If the knob is turned fully
counter-clockwise, no haze will be produced.

10
Installation and setting up
Installation and setting up
DANGER! DO NOT operate the Magnum 2500Hz until you have read and
observed all the precautions listed under “Safety information” on page 4.
Location
The Magnum 2500Hz should be located on a solid surface such as the floor.
The machine can operate in any orientation from 30° upwards to 30° downwards.
Steeper tilting may cause fluid leakage.
Do not suspend the machine over areas where people will be underneath.
Ensure that there is at least 100 mm (4 in.) clearance around the machine and at
least 600 mm (24 in.) in front of the haze output.
AC power
Before using the machine, ensure that a grounding-type (earthed) power plug
that fits the local power outlets is installed on the power cable.
DANGER! Make sure the power plug is correctly rated:
• For EU models fit with a plug rated at 6 A minimum.
• For US models fit with a plug rated at 10 A minimum.
When installing the plug, follow the plug manufacturer’s instructions and connect
pins as follows:
Yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
wire
function
marking
screw colour
brown
live
“L”
yellow or brass
blue
neutral
“N”
silver
green/yellow
earth
green
Before connecting the Magnum 2500Hz to power, verify that the AC supply is
adequately dimensioned for the current draw of the machine. The machine
requires:
EU Models –920 W, 220-240 V
US Models –920 W, 100-130 V
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Martin Service and Support for assistance.

11
Installation and setting up
Setting up
Fill the fluid reservoir with Martin approved haze fluid (see page 19). The fluid
compartment is opened by pulling outwards on the cover (pull using a finger in
the round hole). The cover is held closed by a magnetic catch and hinges
upwards.
If the optional DMX module is fitted and DMX control is being used, connect the
machine to the DMX line (see page 17).
Connect the remote to the REMOTE IN socket on the back panel.
If you are operating several machines using the machine-to-machine link
function, connect the machines in a daisy-chain using RJ45 (computer network)
type cables. The maximum total length of cable, including the remote cable, is 50
m (164 ft.).
Do not connect a computer network to the RJ45 remote / link sockets on the
Magnum 2500Hz. Although the connectors are compatible, the electrical signals
are not, and equipment may be damaged.
To additional
machines

12
Installation and setting up
Final checks
Before applying power to the Magnum 2500Hz, verify the following:
the machine is safely located or installed and meets the location
requirements stated on page 10.
the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 4.
the haze fluid is genuine Martin fluid listed under “Approved Haze Fluid
Types” on page 19.
the machine is electrically grounded (earthed).
the AC power distribution circuits and lines are adequately rated for the
current load.
Turning on the power
Turn on the mains power switch located next to the mains power inlet cable.
The red Heat indicator on the remote and on the rear of the machine will light for
about 6-8 minutes as the machine heats up to operating temperature.
When the green Ready indicator comes on, the machine is ready to make haze.
To obtain maximum output, wait another few minutes for the red Heat
indicator to go off, as haze output is reduced while the unit is heating
up.

13
Control settings
Control settings
Overview
The unit is controlled using the remote control. You can control it in these ways:
Automatic Continuous run mode.
Automatic haze bursts using a repeating timer
You trigger a timed burst of haze using the “one-shot” timer
You can also set the haze output level using the knob.
Continuous Run Mode
Press the FOG button once (for less than one second) to enter continuous run
mode or timer mode. If the timer is set, the timer mode will run automatically,
otherwise continuous mode will be enabled and the machine will produce haze
until the button is pressed again. The green timer LED will light when in
continuous run mode.
Setting the Automatic Timer
The Automatic Timer allows you to set the machine to keep producing timed
bursts of haze without anyone having to press any buttons. You need to set two
times: the run/on time during which the machine will produce haze, and the
wait/off time during which the machine will idle.
1. Press the TIMER SET button. The ON light will flash. You are now
setting the On/Run time.
Output level / timer
programming knob
Machine heating light
Machine ready to fog
light
Fog / Timer engage
button
Timer set button
Timer Off light
Timer On light

14
Control settings
2. Turn the knob to the required “run” time, as shown on the outer scale of
the knob (OFF –255 seconds).
3. Press the TIMER SET button once. The ON light will come on static and
the OFF light will flash. You are now setting the Off/Wait time.
4. Turn the knob to the required “wait” time.
5. Press the TIMER SET button once more. Both ON/OFF lights will come
on to show the timer is programmed.
The run and wait times are now stored and will be remembered even after the
unit has been switched off.
To start the timer using the times you’ve set, press the FOG / TIMER ENGAGE
button briefly. To turn off the timer, press the FOG / TIMER ENGAGE button
briefly again. When the timer is engaged, the ON light will come on during the
On/Run time and the OFF light will come on during the Off/Wait time.
If you only want to change the Off/Wait time, leaving the On/Run time
unchanged, press TIMER SET twice. This will take you directly to
setting the Off time without changing the On time.
To find out what the current time settings are, press TIMER SET then rotate the
knob slowly until the “ON” light begins to flash very rapidly. The knob is now set
to the current run/on time. Press TIMER SET once and rotate the knob slowly
again until the “OFF” light begins to flash very rapidly. The knob is now set to the
current wait/off time. Press TIMER SET again to get back to normal.
Setting the “o ne -shot” timer
The “one shot” timer allows you to pre-program the length of the haze burst. This
can be useful if you want to have a fixed-time burst of haze which you can repeat
at will by pressing the haze button.
1. Press the TIMER SET button. The ON light will flash. You are now
setting the On/Run time.
2. Turn the knob to the required “run” time, as shown on the outer scale of
the knob (OFF –255 seconds).
3. Press the TIMER SET button once. The ON light will come on and the
OFF light will flash.
4. Turn the knob fully right to where “OS” (“One Shot”) is marked.
5. Press the TIMER SET button once more.
The timer is now programmed to one-shot mode and this will be remembered
even after the unit has been switched off.
To produce a timed burst of haze, press the FOG button briefly. To stop the
timed haze output early, press the FOG button briefly again.

15
Control settings
Priming the Machine
If the machine runs out of fluid, it may not pump properly after refilling the fluid
due to airlocks in the fluid pipes.
To prime the machine, hold down the FOG button and turn the knob to
maximum. Keep the button held until the haze output is strong and steady. Then
turn the knob back to the required output level and release the FOG button.
During PRIME mode the machine will prime for 10-seconds if any
airlock is still visible on the fluid line, prime machine again until the
haze output is continuous. Note that you must turn the knob to start
the prime process.
If the machine is left to run when out of fluid, damage may be caused to the
pump leading to premature pump failure. The automatic fluid sensing system will
shut the machine down within approximately 5-minutes of running dry.

16
Control settings
What the status lights mean
The four lights on the remote have the following functions. The red “HEAT” light
and the green “READY” light are also duplicated on the rear of the machine
itself.
HEAT+READY
meaning
no lights
Machine is not powered, or remote is not connected.
heat
Machine is heating but is not yet up to operating
temperature.
heat + ready
Machine is heating and has reached minimum operating
temperature. Haze output level may be reduced while
heating.
ready
Machine has finished heating and is at full operating
temperature.
ready flashing
If the ready LED is flashing, refer to the following code
table.
Single pulse
Calibration Error
Double pulse
Fluid-Out Error
Triple pulse
Overheat Error
OFF+ON
meaning
no lights
Timer is disabled
both on
Timer is programmed but not enabled
“OFF” lit
Timer is running, currently in Off/Wait period
“ON” lit
Timer is running, currently in On/Run period or
continuous mode
“ON” flashing
The timer “ON” time is currently being programmed
“ON” lit, “OFF”
flashing
The timer “OFF” time is currently being programmed

17
DMX control
DMX control
Overview
DMX is a digital control system widely used in entertainment and architectural
lighting. Any controller meeting the DMX-512A standard may be used to control
and program the haze output of the Magnum 2500Hz.
The Magnum 2500Hz requires the optional DMX control module to allow DMX
operation.
Connection
The Magnum 2500Hz provides a 3-pin XLR plug and socket on the rear panel for
DMX connection. The wiring is shown below.
Connector pin
function
1
Ground
2
Data –(“Cold”)
3
Data + (“Hot”)
For best results, use cable designed for high speed digital data transmission.
DMX functions
The Magnum 2500Hz operates from a single DMX channel which gives
proportional control of haze density and the fan from 0-100%.
DMX Level
function
0 –29
No haze
30 –255
Haze at variable density, (30=minimum, 255=maximum)
When the machine is receiving valid DMX data, the indicator light next to the
address switches will light.
It is possible to control the machine by DMX and using the remote control at the
same time, the highest setting will take precedence.
No provision is made for resetting the fluid out condition via the DMX system.
Reset this using the remote or by powering down the machine to perform a full
reset.
Note that the last switch (switch 10) on the DMX address setting dipswitch is
used for the test function not address 512. Setting this switch to ‘on’ will produce
a timer (10 second) burst of haze allowing the machine to be tested without the
remote control being present.

18
DMX control
Setting the DMX start address
Each unit on a DMX system must be allocated an address so that the DMX
controller can send separate commands to the unit. On the Magnum 2500Hz, the
DMX start address is set using the bank of switches (“dip switches”) on the back
panel next to the DMX connectors. The switch settings for each possible DMX
address are given in the table below.
DIP-Switch Setting
0 = OFF
1 = ON
#9
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
#8
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
#7
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
#6
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
#1
#2
#3
#4
#5
0
0
0
0
0
32
64
96
128
160
192
224
256
288
320
352
384
416
448
480
1
0
0
0
0
1
33
65
97
129
161
193
225
257
289
321
353
385
417
449
481
0
1
0
0
0
2
34
66
98
130
162
194
226
258
290
322
354
386
418
450
482
1
1
0
0
0
3
35
67
99
131
163
195
227
259
291
323
355
387
419
451
483
0
0
1
0
0
4
36
68
100
132
164
196
228
260
292
324
356
388
420
452
484
1
0
1
0
0
5
37
69
101
133
165
197
229
261
293
325
357
389
421
453
485
0
1
1
0
0
6
38
70
102
134
166
198
230
262
294
326
358
390
422
454
486
1
1
1
0
0
7
39
71
103
135
167
199
231
263
295
327
359
391
423
455
487
0
0
0
1
0
8
40
72
104
136
168
200
232
264
296
328
360
392
424
456
488
1
0
0
1
0
9
41
73
105
137
169
201
233
265
297
329
361
393
425
457
489
0
1
0
1
0
10
42
74
106
138
170
202
234
266
298
330
362
394
426
458
490
1
1
0
1
0
11
43
75
107
139
171
203
235
267
299
331
363
395
427
459
491
0
0
1
1
0
12
44
76
108
140
172
204
236
268
300
332
364
396
428
460
492
1
0
1
1
0
13
45
77
109
141
173
205
237
269
301
333
365
397
429
461
493
0
1
1
1
0
14
46
78
110
142
174
206
238
270
302
334
366
398
430
462
494
1
1
1
1
0
15
47
79
111
143
175
207
239
271
303
335
367
399
431
463
495
0
0
0
0
1
16
48
80
112
144
176
208
240
272
304
336
368
400
432
464
496
1
0
0
0
1
17
49
81
113
145
177
209
241
273
305
337
369
401
433
465
497
0
1
0
0
1
18
50
82
114
146
178
210
242
274
306
338
370
402
434
466
498
1
1
0
0
1
19
51
83
115
147
179
211
243
275
307
339
371
403
435
467
499
0
0
1
0
1
20
52
84
116
148
180
212
244
276
308
340
372
404
436
468
500
1
0
1
0
1
21
53
85
117
149
181
213
245
277
309
341
373
405
437
469
501
0
1
1
0
1
22
54
86
118
150
182
214
246
278
310
342
374
406
438
470
502
1
1
1
0
1
23
55
87
119
151
183
215
247
279
311
343
375
407
439
471
503
0
0
0
1
1
24
56
88
120
152
184
216
248
280
312
344
376
408
440
472
504
1
0
0
1
1
25
57
89
121
153
185
217
249
281
313
345
377
409
441
473
505
0
1
0
1
1
26
58
90
122
154
186
218
250
282
314
346
378
410
442
474
506
1
1
0
1
1
27
59
91
123
155
187
219
251
283
315
347
379
411
443
475
507
0
0
1
1
1
28
60
92
124
156
188
220
252
284
316
348
380
412
444
476
508
1
0
1
1
1
29
61
93
125
157
189
221
253
285
317
349
381
413
445
477
509
0
1
1
1
1
30
62
94
126
158
190
222
254
286
318
350
382
414
446
478
510
1
1
1
1
1
31
63
95
127
159
191
223
255
287
319
351
383
415
447
479
511

19
Approved Haze Fluid Types
Approved Haze Fluid Types
The following types of Martin haze fluid are suitable for use in this machine.
Martin supplies high quality haze fluids that is based on ultra-pure deionized
water. Use only the following genuine Martin haze fluids. No other fluid is
suitable for use.
DANGER! The Magnum 2500Hz can run safely only on the specific haze fluids it
is designed for. Use ONLY the Martin haze fluids designated in this manual.
NEVER use any other type of fluid, or toxic gas may be produced. You will
probably also cause damage to the system that is not covered by the product
warranty. Do not dilute haze fluid with water or any other liquid. Discard haze
fluid if it becomes contaminated.
RUSH & THRILL Haze Fluid
RUSH & THRILL Haze Fluid is a specially formulated water-based haze fluid
formula and is recommended for use with applicable Martin haze effect
generators. It gives a fine, optically transparent airborne medium with a light-to-
medium index of refraction that is ideal for highlighting beam and aerial FX
projections whilst leaving little to no residue behind. RUSH & THRILL Haze Fluid
is designed as an economy haze fluid that is suitable for use in nightclubs, bars,
stage and outdoor events.
Available in 2.5, 5, 25 and 220 l containers
“Calibration factors have been developed and approved by the Actors’ Equity Association
and the Broadway League for use in measuring theatrical haze with the Magnum
2500Hz™ and RUSH & THRILL Haze Fluid™.
Approved Discontinued Fluids:
RUSH Haze Fluid
RUSH ELX Haze Fluid
Martin Pro Haze Fluid

20
Basic service
Basic service
Before servicing the Magnum 2500Hz, read and observe all the precautions
listed in “Safety information” on page 4. Any service not described in this section
must be carried out by a certified Martin service technician.
Cleaning
Excessive dust, haze fluid, and dirt build up will degrade performance and cause
overheating and damage to the machine that is not covered by the product
warranty. To maintain adequate cooling, dust must be cleaned from the outer
casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The haze output nozzle remains hot for up to 10 hours after use.
Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.
Clean haze fluid residues from the haze output of the machine using a
damp cloth.
Clean the outer casing with a damp cloth only.
Martin Pro Clean and Storage Fluid
Martin Pro-Clean & Storage Fluid is specially designed for optimizing
performance while providing longevity of any effect machine. Martin Pro-Clean &
Storage fluid is the ultimate cleaning solution for Martin atmospheric effect heat
exchangers. This advanced preventative maintenance fluid has been utilized by
Martin service technicians for years of both cleaning and storing effect machines.
Utilizing Martin Pro-Clean & Storage Fluid on a regular basis reduces clogging
and further extends the life of your Martin atmospheric effect machines. By using
the highest-grade chemicals available while remaining eco-friendly, Martin fluids
are both effective and safe.
Instructions for use
Use fluid directly from container, do not dilute. Remove cap and safety seal; if
inner safety seal has been tampered with, return product to point of purchase.
Disconnect effect machine from power source before filling reservoir. When
possible, remove reservoir from machine and carefully fill reservoir to desired
level, taking care not to overfill or spill. Wipe up any spilled fluid with a damp
cloth. Replace cap on container and store upright in a secure location.
Cleaning and Preventative Maintenance Procedure: Use Martin Pro Clean
and Storage Fluid after every 200 hours of operation or monthly depending on
usage and duty cycle. In a well ventilated area temporarily connect Martin Pro
Clean and Storage Fluid to the effect machine being serviced or fill the machines
provided fluid reservoir. Allow the machine to fully heat. When machine is ready
activate the machine to run continuously for 30-45 minutes; use a timer function
if available.
Storage Procedure: Perform the above cleaning and preventative maintenance
procedure. After procedure is completed simply run the machine until all fluid has
been visibly purged from the fluid inlet tubing to prevent leaks and seepage.