MARUTI SUZUKI Tour S User manual

FUEL RECOMMENDATION
1
56RH0-74E
65D394
FUEL RECOMMENDATION
Fuel Recommendation ........................................................ 1-1

1-1
FUEL RECOMMENDATION
56RH0-74E
Fuel Recommendation
Petrol engine
To avoid damaging catalytic converter you
must use unleaded petrol with an octane
number (RON) of 91 or higher.
Do not use petrol with additives containing
metal.
Petrol/Ethanol blends
Blends of unleaded petrol and ethanol
(grain alcohol), also known as gasohol, are
commercially available in certain areas.
Blends of this type may be used in your
vehicle if they are no more than 10% etha-
nol.
Make sure this petrol-ethanol blend has
octane ratings no lower than those recom-
mended for the petrol.
NOTE:
If you are not satisfied with the driveability
or fuel economy of your vehicle when you
are using a petrol/alcohol blend, you
should switch back to unleaded petrol con-
taining no alcohol.
Petrol containing MTBE
Unleaded petrol containing MTBE (methyl
tertiary butyl ether) may be used in your
vehicle if the MTBE content is not greater
than 15%. This oxygenated fuel does not
contain alcohol.
NOTICE
The fuel tank has an air space to
allow for fuel expansion in hot
weather. If you continue to add fuel
after the filler nozzle has automati-
cally shut off or an initial blowback
occurs, the air chamber will become
full. Exposure to heat when fully
fuelled in this manner will result in
leakage due to fuel expansion. To
prevent such fuel leakage, stop filling
after the filler nozzle has automati-
cally shut off, or when initial vent
blowback occurs, if using an alterna-
tive non-automatic system.
NOTICE
Be careful not to spill fuel containing
alcohol while refueling. If fuel is
spilled on the vehicle body, wipe it up
immediately. Fuels containing alco-
hol can cause paint damage, which is
not covered under the New Vehicle
Limited Warranty.

BEFORE DRIVING
74LH0-74E
60G404
BEFORE DRIVING
Keys .........................................................................................2-1
Door Locks ..............................................................................2-2
Keyless Entry System Transmitter .......................................2-3
Security System .....................................................................2-4
Transmitter Battery ................................................................2-10
Windows ..................................................................................2-13
Mirrors .....................................................................................2-14
Front Seats ..............................................................................2-14
Seat Belts and Child Restraint Systems ..............................2-16
Supplemental Restraint System (Air bags) ..........................2-26
Instrument Cluster .................................................................2-32
Speedometer ...........................................................................2-33
Fuel Gauge ..............................................................................2-33
Temperature Gauge ...............................................................2-34
Brightness Control .................................................................2-34
Information Display ................................................................2-35
Warning and Indicator Lights ................................................2-38
Lighting Control Lever ...........................................................2-42
Headlight Leveling Switch .....................................................2-43
Turn Signal Control Lever .....................................................2-43
Hazard Warning Switch .........................................................2-44
Windshield Wiper and Washer Lever ...................................2-44
Tilt Steering Lock Lever .........................................................2-46
Horn ........................................................................................ 2-46

2-1
BEFORE DRIVING
74LH0-74E
Keys
54G489
Your vehicle comes with a pair of keys.
The key(s) may or may not be equipped
with a transmitter depending on model
variant. Keep the spare key in a safe
place. One key can open all of the locks on
the vehicle.
The key identification number is stamped
on a metal tag provided with the keys or on
the keys. Keep the tag (if equipped) in a
safe place. If you lose your keys, you will
need this number to have new keys made.
Write the number below for your future ref-
erence.
Immobilizer System
This system is designed to help prevent
vehicle theft by electronically disabling the
engine starting system.
The engine can be started only with your
vehicle’s original immobilizer ignition key
which has an electronic identification code
programmed into it. The key communi-
cates the identification code to the vehicle
when the ignition switch is turned to the
“ON” position. If you need to make spare
keys or remote controllers, see your Maruti
Suzuki authorised workshop. The vehicle
must be programmed with the correct iden-
tification code for the spare. A key made
by an ordinary locksmith will not work.
80JM122
If the immobilizer light blinks when the igni-
tion switch is in the “ON” position, the
engine will not start.
If this light blinks, turn the ignition switch to
the “LOCK” position, then turn it back to
the “ON” position.
If the light still blinks after the ignition
switch is turned back to the “ON” position,
there may be something wrong with your
key or with the immobilizer system. Ask
your Maruti Suzuki authorised workshop to
have the system inspected.
NOTE:
• If you lose your immobilizer ignition key,
ask a Maruti Suzuki authorised work-
shop as soon as possible to deactivate
the lost one, and to make a new key or
remote controller.
• If you own other vehicles with immobi-
lizer keys, keep those keys away from
the ignition switch when using your
MARUTI SUZUKI vehicle. Otherwise, or
the engine may not be started because
they may interfere with your MARUTI
SUZUKI vehicle’s immobilizer system.
• If you attach any metal objects to the
immobilizer key or remote controller, it
may not start the engine.
Ignition Key Reminder
A buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
KEY NUMBER:
EXAMPLE
NOTICE
The immobilizer key and remote con-
troller are sensitive electronic instru-
ments. To avoid damaging them:
• Do not expose them to impacts,
moisture or high temperature such
as on the dashboard under direct
sunlight.
• Keep them away from magnetic
objects.
Fuel Recommendation: 1, 2

2-2
BEFORE DRIVING
74LH0-74E
Door Locks
Side Door Locks
60B008
To lock a front door from outside the vehi-
cle:
• Insert the key and turn the top of the key
toward the rear of the vehicle, or
• Turn the lock knob forward, then pull and
hold the door handle as you close the
door.
To unlock a front door from outside the
vehicle, insert the key and turn the top of
the key toward the front of the vehicle.
74LM02010
To lock a door from inside the vehicle, turn
the lock knob forward. Turn the lock knob
backward to unlock the door.
To lock a rear door from outside the vehi-
cle, turn the lock knob forward and close
the door.
NOTE:
Be sure to hold the door handle when you
close a locked front door, or the door will
not remain locked.
Central Door Locking System
(if equipped)
60B008
You can lock and unlock all 5 doors (Front,
Rear and Back door) or 4 doors (Front and
Rear only) (Depending upon the specifica-
tion of the vehicle) simultaneously by using
the key in the driver’s door lock.
To lock all (4 or 5) doors simultaneously,
insert the key in the driver’s door lock and
turn the top of the key anticlockwise once.
To unlock all (4 or 5) doors simultaneously,
insert the key in the driver’s door lock and
turn the top of the key clockwise twice.
74LM02011
(1) LOCK
(2) UNLOCK
You can also lock or unlock all doors by
depressing the front or rear of the
switch,(3) respectively.
NOTE:
Individual doors can also be UNLOCKED
anytime by using their respective “Door
Lock Knob” inside the vehicle.
LOCK
UNLOCK
Front
Rear EXAMPLE
UNLOCK
EXAMPLE
Door Lock
Knob
LOCK
UNLOCK
LOCK
Front
Rear EXAMPLE
(2)
(1)
(3)
EXAMPLE
Keys: 8

2-3
BEFORE DRIVING
74LH0-74E
NOTE:
You can also lock or unlock all doors by
operating the transmitter. Refer to “Keyless
Entry System Transmitter” in this section.
NOTE:
• All doors are automatically unlocked when
you change the ignition mode to “LOCK”
(OFF) and pull out the key.
• All doors are automatically locked for
safety when the vehicle speed reaches
15 km/h.
Trunk Lid
68LM246
Your vehicle is equipped with a trunklid
keylock. You can open the trunk lid by
using the key in the trunk lid lock. To open
the trunk lid, insert the key and turn it
clockwise to unlatch and lift the trunklid.
63J054
You can also unlatch the trunklid by pulling
the release lever located on the outboard
side of the driver’s seat.
Keyless Entry System
Transmitter
79MH0237
(1) “LOCK” button
(2) “UNLOCK” button
You can lock or unlock all doors simultane-
ously by operating the transmitter near the
vehicle.
Central door locking system
• To lock all doors, push the “LOCK” but-
ton (1) once.
• To unlock all door, push the “UNLOCK”
button (2) twice.
The turn signal lights will flash once and
the siren will sound once when the doors
are locked.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren will sound twice.
EXAMPLE
WARNING
Always make sure that the trunk lid is
fully opened before using the lug-
gage compartment.
WARNING
Always make sure that the trunk lid is
fully opened before using the lug-
gage compartment.
EXAMPLE
(1) (2)
EXAMPLE
Door Locks: 3, 5, 8

2-4
BEFORE DRIVING
74LH0-74E
• If the interior light switch is in the
“DOOR” position, the interior light will
turn on for about 15 seconds and then
fade out. If you insert the key into the
ignition switch during this time, the light
will start to fade out immediately.
Be sure the doors are locked after you
operate the “LOCK” button (1). If no door is
opened within about 30 seconds after the
“UNLOCK” button (2) is operated, the
doors will automatically lock again.
NOTE:
• The maximum operating distance of the
keyless entry system transmitter is about
5 m (16 ft.), but this can vary depending
on the surroundings, especially near
other transmitting devices such as radio
towers or CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the transmitter, if the ignition key is
inserted in the ignition switch.
• If any door is open, you cannot lock the
door by operating the transmitter, how-
ever unlock the door.
• If you lose one of the transmitters, ask
your Maruti Suzuki authorised workshop
as soon as possible for a replacement.
Be sure to have your dealer program the
new transmitter code in your vehicle’s
memory so that the old code is erased.
Security System
ALARM MODE
The Alarm mode is designed to protect
your vehicle from unauthorized entry. It
operates in three stage:
First: Arm Stage
Second: Trigger Stage
Third: Disarm Stage
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
• Do not expose it to impacts, mois-
ture or high temperature such as
by leaving it on the dashboard
under direct sunlight.
• Keep the transmitter away from
magnetic objects such as a televi-
sion.
Warning LED
EXAMPLE
EXAMPLE
Door Locks: 3, 5, 8

2-5
BEFORE DRIVING
74LH0-74E
Arm Stage
In Arm Stage, your vehicle is monitored for
any unauthorized entry. In order to arm,
press the key LOCK button once.
As response to locking/arming:
1) Doors will get locked & vehicle will get
armed.
2) Visible theft warning LED on security
switch will flash slowly to indicate arm-
ing.
NOTE:
1) Three siren chirps and one light flash of
all indicator lights will indicate that
engine hood is open. However, locking
of all doors take place but security sys-
tem will not be armed.
2) Be sure to close all doors (including the
engine hood and trunk) and windows
before locking/arming the vehicle.
3) System will not Lock/Arm in following
conditions.
a) If any of door is open.
b) If key is in key cylinder.
Trigger Stage
In the event of any unauthorized entry
(without unlocking/disarming) into the vehi-
cle, the alarm triggers and all indicator
lights flash. The triggering of the alarm is in
two stages. First acting as a warning to the
intruder and then alarm drawing the sur-
rounding attention. However, alarm will be
activated without any warning if intrusion
happens through engine hood.
Disarm Stage
System should be brought in Disarm Mode
while you are entering the vehicle. In order
to disarm: Press the key UNLOCK button
once.
As response to unlocking/disarming:
1) Doors will unlock and vehicle will dis-
arm.
2) Visible theft warning LED on security
switch will flash faster than in arm stage
indicating Auto rearm (described in
auto rearm section).
EXAMPLE
EXAMPLE
Trigger Type Alarm Cycle
Door Trigger
(By Driver Door,
Passenger Door,
Engine Hood &
Back Door)
1 Cycle of approxi-
mate 27.5 seconds
Ignition Trigger
1 Cycle of approxi-
mate 27.5 seconds
Impact Trigger
(Built in sensor
Trigger)
1 Cycle of max 4.5
seconds
Door Locks: 3, 5, 8

2-6
BEFORE DRIVING
74LH0-74E
GENERAL FEATURES
Illuminated Entry
When vehicle is unlocked, the room lamp
will turn ON to facilitate illuminated entry
into the vehicle. If no door is opened in
about 15 seconds of above operation,
room lamp will fade out.
If any door is opened after 15 seconds, the
room lamp turns ON again and after 15
seconds of closing all doors room lamp will
fade out.
If within 15 seconds after closing all the
doors the driver inserts the key into the key
cylinder, then the room lamp will fade out.
Illuminated Exit
When key is removed from the key cylin-
der, the room lamp will turn ON to facilitate
illuminated exit. If no door is opened in
about 15 seconds of key removal from key
cylinder, the room lamp will fade out.
When door is opened to exit the vehicle,
the room lamp will turn ON again (if it has
turned OFF after 15 seconds of key
removal from key cylinder) and will turn
OFF after 15 seconds of closing all the
doors.
If within 15 seconds of all doors closure,
vehicle is locked by pressing the LOCK
button, the room lamp will fade out.
NOTE: Room lamp will fade out gradually
approximately in 2 seconds.
Mute Lock/Unlock
To Lock/Unlock the vehicle without siren
chirps use this function.
a) Press and release the Key LOCK &
UNLOCK buttons simultaneously.
b) Press and release Key LOCK or
UNLOCK button for desired function.
Example: To Lock the system without the
Siren chirp sound, press and release the
Key LOCK & UNLOCK button simultane-
ously, then press and release the Key
LOCK button once.
Auto Rearm
In case of accidental Unlock/Disarm of
vehicle by Key, vehicle will automatically
Lock & Arm within 30 sec. without any indi-
cation. Auto rearm cycle gets canceled if
user does any of the following operation
within 30sec :
1. Open any door (including back door).
2. Open Engine Hood.
3. Key On.
Radio Frequency Lock Out
Key Lock/Unlock/Car locator function will
cease to function when Key is inside Key
cylinder.
Car locator function
Car locator function helps in locating the
vehicle.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds.
The turn signal lights will blink for about 27
seconds. Also, the siren will sound for
about 27 seconds at the same time. Press
and release the Key LOCK & UNLOCK
button simultaneously to cancel the car
locator function.
NOTE:
The car locator function will not activate
when the key is in the ignition switch or pre
warning / full blast warning by shock sen-
sor or alarm is in activated condition.
Siren on
for 27 sec.
Light flashes
for 27 sec.
EXAMPLE
Door Locks: 3, 5, 8

2-7
BEFORE DRIVING
74LH0-74E
Flashing LED Status
The flashing LED always reflects the sta-
tus of the system as following.
Intrusion Alert
The system gives a report if it has been
intruded in your absence. Four chirps are
given when UNLOCK button is pressed
after an intrusion.
PROGRAMMABLE FEATURES
System has some features which can be
programmed by user according to their
choice.
Drive Lock Mode
Drive lock mode can be programmed by
SPEED LOCK or can be turned OFF. If
drive lock mode is programmed to SPEED
LOCK, all the vehicle doors will lock when
vehicle attains the speed of 15 Km/hr. If
Drive Lock is programmed to OFF, no door
will lock by speed.
NOTE:
In case of SPEED LOCK Mode, if any door
is open while driving, it will get cancelled.
Once vehicle Speed crosses 15 Km/hr, the
LED on Security Switch will blink for 5 sec-
onds as indication of door open.
Drive Unlock Mode
Drive unlock can be programmed to KEY
or can be turned OFF. When programmed
to KEY, turning Ignition ON to OFF then
removing the key from the key cylinder will
unlock all the doors. If drive unlock is pro-
grammed to OFF then no door will unlock
by removing key from key cylinder.
Siren Chirp ON/OFF feature
Siren Chirps can be programmed to ON or
OFF. When siren chirp feature disabled,
siren will not chirp after Arm/Disarm by
LOCK/UNLOCK button.
Shock Sensor feature
This is a very important feature of security
system. It enables protection of your vehi-
cle against any major impact. If anybody
tries to intrude into the vehicle, the warning
may trigger. Triggering of the warning is of
two types: pre-warning and full blast warn-
ing. The sensitivity of shock sensor can be
adjusted as desired by the user.
PROCEDURE TO PROGRAM FEATURE
System Condition LED Status
Disarmed condition LED does not
glow
Armed condition Slow Flashes
of LED
Diagnostic
report Visual-LED Sound
Built in Shock
Sensor Trigger
(full blast warn-
ing)
2 Flashes Four
Chirps
Door/Trunk/
Engine Hood
Intrusion
3 Flashes Four
Chirps
Ignition 5 Flashes Four
Chirps
Sl.
No. Feature 1 Chirp 2 Chirps Default
1. Drive Lock
Mode Speed OFF Speed
2. Drive Unlock
Mode Key OFF Key
3. Siren chirp
ON/OFF ON OFF ON
4. Shock Sen-
sor ON/OFF ON OFF ON
Door Locks: 3, 5, 8

2-8
BEFORE DRIVING
74LH0-74E
Programming Drive Lock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
One time.
d) Press and hold the Security switch.
e) One chirp sound confirms entry into
Drive Lock programming mode.
f) Press the Key “Lock” button (while
holding the Security switch), a single
chirp sound confirms mode changed to
speed lock.
g) Two-Siren chirp sound confirms Drive
lock mode OFF.
h) Release the Security switch.
i) Turn the Ignition ON.
Programming Drive Unlock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
two times.
d) Press and hold the Security switch.
e) Two-chirp sound confirms entry into
Drive unlock programming mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
key Unlock.
g) Two-siren chirp sound confirms the
mode changed to Drive Unlock mode
OFF.
h) Release the Security switch.
i) Turn the Ignition ON.
Programming Siren Chirp ON/OFF
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
Three times.
d) Press and hold the Security switch.
e) Three-chirp sound confirms entry into
Siren Chirp ON/OFF programming
mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
Siren Chirp ON.
g) Two-Siren chirp sound confirms the
mode changed to Siren Chirp OFF.
h) Release the Security switch.
i) Turn the Ignition ON.
Door Locks: 3, 5, 8
Windows: 3, 8

2-9
BEFORE DRIVING
74LH0-74E
Programming Shock Sensor ON/OFF
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
Four times.
d) Press and hold the Security switch.
e) Four-chirp sound confirms entry into
Shock Sensor ON/OFF programming
mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
shock sensor ON.
g) Two-Siren chirp sound confirms the
mode changed to shock sensor OFF.
h) Release the Security switch.
i) Turn the Ignition ON.
Shock Sensor Sensitivity Adjustment
via Key
Full Blast adjustment
Full Blast can be adjusted in 16 levels as
mentioned below.
a) Press Unlock button on Key to Unlock/
Disarm the System.
b) Press Lock button (within 2 seconds of
key UNLOCK) on Key to Lock/Arm the
System.
c) Within 2 sec press Lock & Unlock button
simultaneously for at least 3 sec. Siren
will give Long chirp to confirm entry into
sensitivity adjustment mode
i) Press Lock button to adjust the sen-
sitivity one step lower. Siren will give
one chirp every time lock button is
pressed till at level 1 where it will
give a long chirp. When adjusted to
level 1, Full Blast will turn OFF
ii) Press unlock button to adjust the
sensitivity one step higher. Siren will
give two chirp every time unlock but-
ton is pressed till at level 16 where it
will give a long chirp.
Pre-warn Adjustment
Pre-warn can be adjusted in 16 levels as
mentioned below:
a) Press Lock button on Key to Lock/Arm
the System
b) Press Unlock button (within 2 seconds
of key LOCK) on Key to Unlock/Disarm
the System
c) Within 2 sec press Lock & Unlock button
simultaneously for at least 3 sec. Siren
will give Long chirp to confirm entry into
Sensitivity Adjustment Mode.
i) Press Lock button to adjust the sen-
sitivity one step lower. Siren will give
one chirp every time lock button is
pressed till at level 1 where it will
give a long chirp. When adjusted to
level 1, pre-warn will turn OFF.
ii) Press Unlock button to adjust the
sensitivity one step higher. Siren will
give two Chirp every time Unlock
button is pressed till at level 16
where it will give a long chirp.
Program Customer Pin-code
(Personalized Pin-code)
If transmitter is not working properly, then it
is possible to disarm the system by Per-
sonalized pin code.
The Personalized 4-digit number can be
changed from the factory default to ensure
Personalized Security.
Windows: 3, 8

2-10
BEFORE DRIVING
74LH0-74E
Pin code entry
a) Disarm the system.
b) Open the Driver Door.
c) Turn Ignition ON then OFF.
d) Within 5 seconds press and release
Valet switch 5 times. A short chirp fol-
lowed by long chirps confirms entry into
Pin Code programming mode.
e) Press Lock button on Key, after a single
chirp enter the First digit (within 1-9) by
pressing Valet switch (for e.g. to enter 2
press and release Valet switch two
times).
f) Press Lock button on Key, after two
chirp enter the Second digit (within 1-9)
by pressing Valet switch.
g) Press Lock button on Key, after 3-
chirps enter the Third digit (within 1-9)
by pressing Valet switch.
h) Press Lock button on Key, after 4-
chirps enter the Fourth digit (within 1-9)
by pressing Valet switch.
Emergency Disarm by Personalized pin
code
The Personalized 4- Digit Pin Code acts as
a secret Key, to Emergency Disarm the
vehicle.
a) Turn the Ignition ON, OFF and then
ON.
b) Enter the First digit (for e. g. to enter 2
press and release Valet switch twice)
c) Turn the Ignition OFF then ON.
d) Enter the Second digit.
e) Turn the Ignition OFF and then ON.
f) Enter the Third Digit.
g) Turn the Ignition OFF and then ON
h) Enter the Last Digit.
i) Turn the Ignition OFF and then ON.
j) The vehicle will get disarmed.
NOTE:
The default pin will be provided by the
dealer at the time of delivery. It is recom-
mended to personalize the pin for
increased security. The pin must be
remembered as it is not possible to retrieve
a lost pin.
Transmitter battery
Replacement of the Battery
If the transmitter battery gets discharged,
replace the battery with a new one.
To replace the battery of the transmitter:
1) Remove the screw (1), and open the
transmitter cover.
2) Remove the transmitter (2).
3) Put the edge of a flat blade screw driver
in the slot of the transmitter (2) and pry
it open.
EXAMPLE
Windows: 3, 8

2-11
BEFORE DRIVING
74LH0-74E
4) Replace the battery (3) (Lithium disc
type CR1620) so that its +ve terminal
faces the bottom cover of the transmit-
ter (5).
5) Close the transmitter and install it into
the transmitter holder.
6) Close the transmitter cover, install and
tighten the screw (1).
7) Make sure the door locks can be oper-
ated with the transmitter.
NOTE:
Normal battery life is approximately 2
years, but varies depending on usage. It is
advisable to get battery replaced from
Maruti Suzuki authorised workshop.
(2)
(3)
(5)
EXAMPLE
CAUTION
Do not remove the screw from the
key Unnecessarily as it damages the
screw head. Kindly replace the screw
once the transmitter battery is
changed.
CAUTION
Dispose off the used battery properly
according to applicable rules or regu-
lations. Do not dispose off lithium
batteries with ordinary household
trash.
WARNING
Swallowing a lithium battery may
cause serious internal injury. Do not
allow anyone to swallow a lithium
battery. Keep lithium batteries away
from children and pets. If swallowed,
contact a physician immediately.
EXAMPLE
Mirrors: 3, 8

2-12
BEFORE DRIVING
74LH0-74E
TROUBLESHOOTING
SYMPTOMS PROBABLE CAUSES REMEDIES
Transmitter function (Unlock/Lock/car
locator function) not working
1. Battery of the transmitter is weak.
2. Transmitter is exposed to water or it is
wet.
3. D/L or Dome fuse for controller is blown
in the vehicle.
4. In case if any door is open or door
sensor is shorted with the body ground,
remote will not activate the central
locking/ alarm system.
1. Check the battery.
2. Dry the transmitter and check it.
3. Check and replace the D/L or Dome
fuse.
4. Check if all doors are properly closed
and door switch functioning is O.K.
Operation distance of the transmitter is
less than 20m but still transmitter (Unlock/
Lock/car locator) is not working
1. Battery of the transmitter is weak.
2. Strong RF interference. (e.g. Radio
Towers, High Voltage Transmission line
near by)
1. Check the battery.
2. Drive the vehicle away from the
particular spot and re-test the control
distance.
It is difficult to activate or deactivate the
system in certain area using the
transmitter.
1. The strong interference caused by
excessive RF activity in a particular
area
1. The interference is temporary and only
while the vehicle is in that area.
Alarm is not triggered even if any door(s)/
engine hood/trunk opened in arm stage.
1. The contact point of the door(s), front
bonnet or rear boot switch is faulty.
2. The connection of the door(s), front
bonnet or rear boot switch is loose.
1. Replace the defective Switch.
2. Make proper connection.
Siren does not sound when alarm is
triggered.
1. The connection of the siren wire is
loose.
2. Siren is faulty.
1. Make proper connection.
2. Change the siren.
Mirrors: 3, 8
Seat Adjustment: 3

2-13
BEFORE DRIVING
74LH0-74E
Windows
Manual Window Control
(if equipped)
60G010
Raise or lower the door windows by turning
the handle located on the door panel.
Electric Window Controls
(if equipped)
The electric windows can only be operated
when the ignition switch is in the “ON”
position.
Driver’s door
74LM02012
The driver’s door has a switch (1) to oper-
ate the driver’s window, and a switch (2) to
operate the front passenger’s window.
Passenger’s door (if equipped)
74LM02014
The passenger’s door has a switch (3) to
operate the passenger’s window.
81A009
To open a window, push the top part of the
switch and to close the window lift up the
top part of the switch.
The driver’s window has an “auto-down”
feature for added convenience (at toll
booths or drive-through restaurants, for
example). This means you can open the
window without holding the window switch
in the “Down” position. Press the driver’s
window switch completely down and
release it. To stop the window before it
reaches the bottom, pull the switch up
briefly.
Lock switch
74LM02013
The driver’s door also has a lock switch for
the passenger’s windows. When you push
in the lock switch, the passenger’s win-
dows cannot be raised or lowered by oper-
ating any of the switches (2) or (3). To
restore normal operation, release the lock
switch by pushing again.
EXAMPLE
(1)
(2)
EXAMPLE
(3)
EXAMPLE
CLOSE
OPEN
EXAMPLE
EXAMPLE

2-14
BEFORE DRIVING
74LH0-74E
NOTE:
If you drive with one of the rear windows
open, you may hear a loud sound caused
by air vibration. To reduce the sound, open
the driver’s or front passenger’s window, or
narrow the rear window opening.
Mirrors
Inside Rearview Mirror
74LHT0235
You can adjust the inside rearview mirror
by hand so as to see the rear of your vehi-
cle in the mirror. To adjust the mirror, move
the mirror up, down or side ways by hand
to obtain the best view.
Outside Rearview Mirrors
Adjust the outside rearview mirrors so you
can just see the side of your vehicle in the
mirrors.
75J003
You can adjust the outside rearview mir-
rors by hand with the knob (1) located on
the driver’s or front passenger’s door
panel.
Front Seats
Precaution for front passenger seat
For seat with seat belt reminder, refer to
the NOTICE in the “Front passenger’s seat
belt reminder” section.
Seat Adjustment
WARNING
• You should always lock the pas-
senger’s window operation when
there are children in the vehicle.
Children can be seriously injured if
they get part of their body caught
by the window during operation.
• To avoid injuring an occupant by
window entrapment, be sure no
part of the occupant’s body such as
hands or head is in the path of the
electric windows when closing
them.
• Always remove the ignition key
when leaving the vehicle even if
only for a short time. Also do not
leave children alone in a parked
vehicle. Unattended children could
use the electric window switches
and get trapped by the window.
WARNING
Be careful when judging the size or
distance of a vehicle or other object
seen in the side convex mirror. Be
aware that objects look smaller and
appear farther away than when seen
in a flat mirror.
EXAMPLE
WARNING
Never attempt to adjust the driver’s
seat or seatback while driving. The
seat or seatback could move unex-
pectedly, causing loss of control.
Make sure that the driver’s seat and
seatback are properly adjusted
before you start driving.
(1)
EXAMPLE

2-15
BEFORE DRIVING
74LH0-74E
Adjusting Seat Position
74LM02015
The adjustment lever for each front seat is
located under the front of the seat. To
adjust the seat position, pull up on the
adjustment lever and slide the seat forward
or rearward.
After adjustment, try to move the seat for-
ward and rearward to ensure that it is
securely latched.
If the driver’s seat is equipped with a seat
height adjuster lever on the outboard side
of the seat, raise or lower the seat by pull-
ing up or down the adjuster lever.
Adjusting Seatbacks
74LM02016
To adjust the seatback angle of front seats,
pull up the lever on the outboard side of
the seat, move the seatback to the desired
position, and release the lever to lock the
seatback in place.
WARNING
To avoid excessive seat belt slack,
which reduces the effectiveness of
the seat belts as a safety device,
make sure that the seats are adjusted
before the seat belts are fastened.
WARNING
Do not place any object under the
front seat. If an object becomes
caught under the front seat, the fol-
lowing may occur.
• The seat will not be latched.
WARNING
Do not leave cigarette lighters or
spray cans on the floor. If a cigarette
lighter or spray can is on the floor, it
may light accidentally when luggage
is loaded or the seat is adjusted,
causing a fire.
NOTICE
Do not rest your feet on the seat
adjustment lever or push it down.
This may affect the performance of
the seat adjusters.
EXAMPLE
WARNING
All seatbacks should always be in an
upright position when driving, or seat
belt effectiveness may be reduced.
Seat belts are designed to offer maxi-
mum protection when seatbacks are
in the upright position.
EXAMPLE

2-16
BEFORE DRIVING
74LH0-74E
Adjustable Head Restraints
63J246
Head restraints are designed to help
reduce the risk of neck injuries in the case
of an accident. Adjust the head restraint to
the position which places the center of the
head restraint closest to the top of your
ears. If this is not possible for very tall pas-
sengers, adjust the head restraint as high
as possible.
NOTE:
It may be necessary to recline the seat-
back to provide enough overhead clear-
ance to remove the head restraint.
Front
80JS082
To raise the front head restraint, pull
upward on the restraint until it clicks. To
lower the restraint, push down on the
restraint while holding in the lock lever. If a
head restraint must be removed (for clean-
ing, replacement, etc.), push in the lock
lever and pull the head restraint all the way
out.
Seat Belts and Child Restraint
Systems
65D231
WARNING
• Never drive the vehicle with the
head restraints removed.
• Do not attempt to adjust the head
restraint while driving.
EXAMPLE
EXAMPLE
WARNING
• Wear Your Seat Belts at All Times.
• An air bag supplements (if
equipped), or adds to, the frontal
crash protection offered by seat
belts. The driver and all passengers
must be properly restrained by
wearing seat belts at all times,
whether or not an air bag (if
equipped) is mounted at their seat-
ing position, to minimize the risk of
severe injury or death in the event
of a crash.
• Do not modify, remove, disassem-
ble seat belts. Doing so may pre-
vent them from functioning
properly and cause the risk of
severe injury or death in the event
of a collision.
EXAMPLE

2-17
BEFORE DRIVING
74LH0-74E
65D606 65D201 65D199
WARNING
• Never allow persons to ride in the
cargo area of a vehicle. In the event
of an accident, there is a much
greater risk of injury for persons
who are not riding in a seat with
their seat belt securely fastened.
• Seat belts should always be
adjusted as follows:
– the lap portion of the belt should
be worn low across the pelvis,
not across the waist.
– the shoulder straps should be
worn on the outside shoulder
only, and never under the arm.
– the shoulder straps should be
away from your face and neck,
but not falling off your shoulder.
(Continued)
Above the pelvis
EXAMPLE
WARNING
(Continued)
• Seat belts should never be worn
with the straps twisted and should
be adjusted as tightly as is com-
fortable to provide the protection
for which they have been designed.
A slack belt will provide less pro-
tection than one which is snug.
• Make sure that each seat belt
buckle is inserted into the proper
buckle catch. It is possible to cross
the buckles in the rear seat.
(Continued)
Across the pelvis
EXAMPLE
WARNING
(Continued)
• Pregnant women should use seat
belts, although specific recommen-
dations about driving should be
made by the woman’s medical advi-
sor. Remember that the lap portion
of the belt should be worn as low
as possible across the hips, as
shown in the diagram.
• Do not wear your seat belt over
hard or breakable objects in your
pockets or on your clothing. If an
accident occurs, objects such as
glasses, pens, etc. under the seat
belt can cause injury.
(Continued)
as low as possible
across the hips
EXAMPLE