Marvel MVA-802 User manual

1

2
IMPORTANT SAFEGUARDS
When using electrical appliances especially when children are present, basic safety precautions should always be followed to reduce
the risk of re, electric shock, and/or injury to persons, including the following:
1. READ ALL INSTRUCTIONS.
2. Do not touch hot surfaces. Use any handles or knobs.
3. To protect against re, electrical shock, or injury to persons DO NOT immerse cord, plug or appliance in water or other liquid.
4. Close supervision is necessary when any appliance is used by or near children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking o󰀨 parts and before cleaning.
6. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner.
Return appliance to the nearest authorized service facility for examination, repair or adjustment.
7. The use of accessory attachments not recommended by the appliance manufacturer may result in re, electric shock or injury to
persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Extreme caution must be used when moving an appliance containing hot food, hot oil, water or other hot liquids.
12. Do not use appliance for other than intended use.
13. To disconnect, turn O󰀨, then remove plug from wall outlet.
14. Scalding may occur during brewing process if Brewer is not assembled or operated properly. Do not attempt to open the hinged front
cover during the brewing process or in the few seconds following the completion of brewing.
15. Fill the water reservoir of this appliance with water only. Do not ll with other liquids or foods, except when following the specic
instructions in this guide for descaling or cleaning the machine.
SAVE THESE INSTRUCTIONS

3

4
This appliance is for HOUSEHOLD USE ONLY. It may be plugged into an AC electrical outlet (ordinary household current). Do not use
any other electrical outlet.
POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to t into
a polarized outlet only one way. If the plug does not t fully into the outlet, reverse the plug and try again. If it still does not t, contact a
qualied electrician. Do not attempt to modify the plug in any way.
SHORT CORD INSTRUCTIONS
A short power-supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord. Extension
cords are available and may be used if care is exercised in their use. If an extension cord is used,
1. The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and
2. The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped
over unintentionally.
LINE CORD SAFETY TIPS
1. Never pull or yank on cord or the appliance.
2. To insert plug, grasp it rmly and guide it into outlet.
3. To disconnect appliance, grasp plug and remove it from outlet.
4. Before each use, inspect the line cord for cuts and/or abrasion marks. If any are found, this indicates that the appliance should be
serviced and the line cord replaced.
5. Never wrap the cord tightly around the appliance, as this could place undo stress on the cord where it enters the appliance and cause
it to fray and break.
DO NOT OPERATE APPLIANCE IF THE LINE CORD SHOWS ANY DAMAGE, OR IF APPLIANCE WORKS INTERMITTENTLY OR
STOPS WORKING ENTIRELY.
IMPORTANT
During the rst few minutes of initial use, you may notice smoke and/or a slight odor. This is normal and should quickly disappear. It will
not recur after appliance has been used a few times.

5
CAUTION: There are two sharp needles that puncture the K-Cup® capsule. One is permanent and is located in the brewer
above the removable K-Cup® Capsule Holder and the other is in the bottom of the removable K-Cup® Capsule Holder. To
avoid risk of injury, do not put your ngers inside the K-Cup® Capsule Holder or inside or near the needle inside the brewer.
CAUTION: There is extremely hot water in the K-Cup® Capsule Holder during the brewing process. To avoid risk of injury,
do not open the hinged front cover during the brewing process.
WARNING: To reduce the risk of re or electric shock, do not remove the bottom cover of the brewer. No user serviceable parts
are inside. Repair should be done by authorized service personnel only.
UNPACKING:
1. Carefully unpack the brewer and all parts. Remove any tape, labels or packaging materials.
2. Wash Water Tank, Water Tank Lid, Drip Tray, Drip Tray Cover, K-Cup® Capsule Holder and Adapter for Ground Co󰀨ee with warm,
soapy water. Rinse well and dry all parts thoroughly.
3. Wipe exterior surfaces of the product with a soft, damp cloth to remove dust particles collected during packing and handling. NEVER
IMMERSE THE BREWER, CORD OR PLUG IN WATER OR ANY OTHER LIQUID.
4. Place Brewer on a solid, level, heat-resistant surface.
PREPARING FOR USE
CLEAN THE SYSTEM:
Before the rst use, it is recommended to run a brew cycle using water only.
1. Fill the Water Tank to the MAX level.
2. Place the Water Tank on the Brewer and put the Lid on the Water Tank.
3. Raise the decorative front cover and make sure the K-Cup® Capsule Holder is properly inserted into the Brewer. DO NOT use a
K-Cup® when cleaning the system.
4. Close the decorative front cover of the Co󰀨ee Brewer.
5. Place a large cup or measuring cup, with a minimum capacity of 16 ounces, on the Drip Tray or beneath the Brew Spout with the
Drip Tray removed.

6
6. Plug the cord into an electrical outlet. Ideally, the Co󰀨ee Brewer should be operated on its own circuit, separate from other appliances.
7. When plugged in, a white light around all buttons will ash three times and then all lights will turn o󰀨.
NOTE: If the decorative front cover is not closed when the power cord is plugged in, then all buttons will ash in red until the front
cover is closed. When closed, the lights will all turn o󰀨.
8. Press and hold the POWER button for 3 seconds. The POWER button will ash and the cleaning cycle will begin.
9. The Brewer will pump water for approximately 25 seconds and then pause for approximately 10 seconds. This cycle will repeat 5
times and the POWER button will ash for the entire cleaning process. At the end of the 5th cycle, the pump will push air for a few
seconds. When the cleaning cycle is complete, the POWER button will turn o󰀨.
10. The Co󰀨ee Brewer is now ready for use.
BREWING COFFEE USING A K-Cup® CAPSULE
1. Place the Co󰀨ee Brewer on a dry, level and heat-resistant surface.
2. Fill the Water Tank to the MAX line and place the Water Tank on the Brewer and put the Lid on the Water Tank.
3. Plug the cord into an electrical outlet. Ideally, the Co󰀨ee Brewer should be operated on its own circuit, separate from other appliances.
4. When plugged in, a white light around all buttons will ash three times and then all lights will turn o󰀨.
NOTE: If the decorative front cover is not closed when the power cord is plugged in, then all buttons will ash in red until the front
cover is closed. When closed, the lights will all turn o󰀨.
5. Raise the decorative front cover. When raised, all buttons will ash in red until the front cover is closed. When closed, the lights will
all turn o󰀨.
6. Slide out the Capsule Holder.
7. Insert a K-Cup® capsule into the Capsule Holder.
NOTE: Never remove or puncture the foil top of the K-Cup® capsule before inserting it into the Co󰀨ee Brewer.
8. Place the Capsule Holder into the Brewer and close the decorative front cover. The K-Cup® capsule will be punctured on the top and
bottom allowing for the ideal ow of water during the brewing cycle.
NOTE: If the decorative front cover is not properly closed, the capsule may not be punctured and the brew cycle may fail.
9. Place a mug on the Drip Tray and under the Brew Spout.
TIP: Be sure to keep the mug in place at the end of the brew cycle to catch any excess drips. The end of the brew cycle
is indicated when all lights turn o󰀨.
10. Press the Power Button. The light around the Power Button will be solid white and the lights around the Cup Size Buttons will ash
white.
11. Press the desired Cup Size Button (6 oz, 8 oz or 10 oz). The Cup Size Button pressed will become solid white and the brew cycle
will begin.

7
12. When the brew cycle is complete, all lights will turn o󰀨 and the Co󰀨ee Brewer will shut o󰀨.
13. Do not leave used co󰀨ee capsules in the Brewer. Wait for the Brewer to cool before removing used capsules as they remain hot
following the brew cycle. Raise the decorative front cover, carefully slide out the Capsule Holder, remove the used capsule and
discard.
BREWING COFFEE USING COFFEE GROUNDS
1. Place the Co󰀨ee Brewer on a dry, level and heat-resistant surface.
2. Fill the Water Tank to the MAX line and place the Water Tank on the Brewer and put the Lid on the Water Tank.
3. Plug the cord into an electrical outlet. Ideally, the Co󰀨ee Brewer should be operated on its own circuit, separate from other appliances.
4. When plugged in, a white light around all buttons will ash three times and then all lights will turn o󰀨.
NOTE: If the decorative front cover is not closed when the power cord is plugged in, then all buttons will ash in red until the front
cover is closed. When closed, the lights will all turn o󰀨.
5. Raise the decorative front cover. When raised, all buttons will ash in red until the front cover is closed. When closed, the lights will
all turn o󰀨.
6. Slide out the Capsule Holder.
7. Fill the Ground Co󰀨ee Adapter with 2 Tablespoons of ground co󰀨ee. A medium to coarsly ground co󰀨ee is recommended. Do not
pack the ground co󰀨ee in the Adapter.
8. Insert the Ground Co󰀨ee Adapter into the Capsule Holder.
9. Place the Capsule Holder into the Brewer and close the decorative front cover.
10. Place a mug on the Drip Tray and under the Brew Spout.
TIP: Be sure to keep the mug in place at the end of the brew cycle to catch any excess drips. The end of the brew cycle
is indicated when all lights turn o󰀨.
11. Press the Power Button. The light around the Power Button will be solid white and the lights around the Cup Size Buttons will ash
white.
12. Press the desired Cup Size Button (6 oz, 8 oz or 10 oz). The Cup Size Button pressed will become solid white and the brew cycle
will begin.
13. When the brew cycle is complete, all lights will turn o󰀨 and the Co󰀨ee Brewer will shut o󰀨.
14. Do not leave used co󰀨ee grounds in the Brewer. Wait for the Brewer to cool before removing co󰀨ee grounds as they remain hot
following the brew cycle. Raise the decorative front cover, carefully slide out the Capsule Holder, remove the Ground Co󰀨ee Adapter
and discard co󰀨ee grounds.

8
USER MAINTENANCE INSTRUCTIONS
This appliance contains no user serviceable parts. Do not try to repair it yourself. Refer it to qualied service personnel if servicing is
needed. The Brewer should be cleaned on a regular basis to prolong the life of the machine and to guarantee optimal brewing results.
TO CLEAN:
• Turn o󰀨 the Brewer and unplug from the wall outlet.
• On a regular basis, check the Drip Tray for excess water or co󰀨ee. Empty the Drip Tray and wipe both parts clean with a damp cloth.
Use extra care when removing or emptying the Drip Tray, in order to prevent spilling any excess liquids from the Drip Tray.
• DO NOT leave used co󰀨ee capsules in the Capsule Holder.
• Wipe down the outside surfaces of the Brewer with a damp cloth and dry thoroughly. NEVER use harsh chemicals or abrasive
cleaning pads. NEVER immerse the Brewer in water or any other liquid and NEVER place the brewer under running water.
• Clean the Water Tank, Water Tank Lid, Drip Tray, Drip Tray Cover Capsule Holder and Ground Co󰀨ee Adapter with warm, soapy
water. Do not use harsh chemicals or abrasive cleaners. Dry thoroughly prior to use. Only the Capsule Holder or Ground Co󰀨ee
Adapter should be cleaned in a dishwasher and should be placed on the top rack only Use low temperature cycles if cleaning the
parts in the dishwasher.
DESCALING:
It is advised to descale the Brewer on a regular basis. Frequency of descaling the Brewer depends on the amount of use and local water
conditions. As a general time frame, the Brewer should be descaled every three months. Specic descaling products for co󰀨ee makers
are available in stores and online.
Follow the specic instructions for the descaling product on the package from the descaling product manufacturer.
• Make sure the Brewer is turned O󰀨.
• Fill the Water Tank with undiluted white vinegar or if using a descaling product ll according to the instructions on the package of the
descaling product.
• Place a large cup or measuring cup, with a minimum capacity of 16 ounces, on the Drip Tray or beneath the Brew Spout with the
Drip Tray removed.
• Make sure there is not a co󰀨ee capsule in the Capsule Holder and close the decorative front panel.
• To start the cleaning cycle, press and hold the POWER button for approximately 3 seconds. The POWER button will ash and the
cleaning cycle will begin.
• The Brewer will pump water for approximately 25 seconds and then pause for approximately 10 seconds. This cycle will repeat 5

9
times and the POWER button will ash for the entire cleaning process. At the end of the 5th cycle, the pump will push air for a few
seconds. When the cleaning cycle is complete, the POWER button will turn o󰀨.
• Empty the dispensed liquid that has accumulated in the measuring cup.
• Allow the Brewer to sit for a few minutes and then run another cleaning cycle using fresh, cold water.
• Following the 2 cleaning cycles, run 3 regular brew cycles on the 10-ounce setting. Each time run the cycle without a co󰀨ee capsule.
This will clean the Brewer and get rid of any residual taste from the vinegar or descaler.
• The Brewer is now ready for regular use again.
TO STORE:
• Be sure all parts are clean and dry before storing. Store appliance in its box or in a clean, dry place. Never store it while it is hot or
wet. Never wrap cord tightly around the appliance; keep it loosely coiled.
• ALWAYS store the Brewer in an upright position, as a small amount of water may remain in the boiler.

10
TROUBLESHOOTING GUIDE
FAULT POSSIBLE CAUSE SUGGESTED CORRECTION
After the Brewer had been plugged in
and powered on, no lights will illumi-
nate and brewing will not start.
If the Brewer has been idle for more
than 5 minutes, it will automatically
shut down.
Press the POWER Button on the
Brewer to start use.
The Brewer stopped and the POWER
Button is ashing red.
The Brewer is either out of water or
the Water Tank has been removed.
Rell and replace the Water Tank and
press the POWER Button. The brew
cycle will continue brewing at the point
at which it was interrupted and will
dispense the volume of liquid to
nish the original cup size which was
selected.
The POWER Button and all Cup Size
Buttons are ashing red. The decorative front cover is open.
Fully close the decorative front cover
and the ashing lights should stop.
The cover should never be opened
during brewing, but if this occurs the
brew cycle will resume immediately
after the front cover is closed.