Marvel MLCR215-IS01B User manual

OWNER’S GUIDE & SERVICE MANUAL
MARVEL UNDERCOUNTER REFRIGERATION
Model: MLCR215-IS01B

WELCOME
Welcome to the Marvel Experience!
Thank you for choosing our quality American-built product
to add to your home. We are thrilled to welcome you to
our growing community of Marvel owners, who trust in our
products and our support.
The information in this guide is intended to help you install
and maintain your new Marvel undercounter model to
protect and prolong its lifetime. We encourage you to
contact our Technical Support team at [phone] with
any questions.
Got a Marvelous Design?
We would love to see how your Marvel product looks in its
new home. You can send us photos of your installed
product at [email protected], and we
might feature your Marvel home design on our website and
social media!
Online registration
available at
marvelrefrigeration.com
Warranty Registration
It is important you register your product warranty after
taking delivery of your appliance. You can register online at
www.marvelrefrigeration.com.
The following information will be
required when registering your
appliance:
Serial Number
Date of Purchase
Dealer’s name and address
The serial number can be found on the serial plate which is
located inside the cabinet on the left side near the top.

TABLE OF CONTENTS
Tip: Click on any section below to jump directly there
Installation
Integrated Panel Dimensions
Integrated Panel Installation
3

Integrated Panel Dimensions
'XHWRGLႇHUHQFHVLQVXUURXQGLQJFDELQHWU\WKHSDQHO
PD\QRWSHUIHFWO\DOLJQZLWKGRRU7KHSURFHGXUHEHORZ
LVGHVLJQHGWRSURYLGHD¿QLVKHGLQWHJUDWHGSDQHOWKDW
VHDPOHVVO\LQWHJUDWHVZLWKVXUURXQGLQJFDELQHWU\
7KHGRRUSDQHOPXVWQRWZHLJKPRUHWKDQOEVNJ
,WLVLPSRUWDQWWRHQVXUHWKDWDOOGULOOHGKROHVDUHGULOOHGWR
WKHFRUUHFWGHSWKLQRUGHUWRDYRLGVSOLWVLQWKHZRRGZKHQ
KDUGZDUHLVLQVWDOOHG
:KHQDSSO\LQJDQLQWHJUDWHGSDQHOWRDXQLWHQVXUHWKDW
ERWKVLGHVDUH¿QLVKHGLQRUGHUWRSUHYHQWZDUSLQJ,QVRPH
SDQHOLQVWDOODWLRQVWKHSDQHOPD\EHYLVLEOHWKURXJKWKH
JODVVZKLOHWKHGRRULVRSHQ
$IXOOLQWHJUDWHGGRRUSDQHOFRPSOHWHO\FRYHUVWKHGRRU
IUDPHDQGSURYLGHVDEXLOWLQDSSHDUDQFH
Integrated Panel Preparation
 &XWWKHSDQHOVWRWKHGLPHQVLRQVOLVWHGLQWKHGLDJUDP
EHORZ
2SWLRQDO6WDLQRU)LQLVKSDQHOWRGHVLUHGVWDLQRUFRORU
%HVXUHWRFORVHO\IROORZWKHLQVWUXFWLRQVSURYLGHGE\WKH
PDQXIDFWXUHU
 2SWLRQDO,QVWDOOKDQGOHVDQGKDUGZDUH
INTEGRATED PANEL DIMENSIONS
NOTE
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY PANEL FLAT AND WITHOUT
INTERFERENCE
3/4"
(20 mm)
Integrated Panel
14-3/4"
(375 mm)
30-1/4"
(768 mm)
4

INTEGRATED PANEL INSTALLATION
Integrated Panel Installation
1. Fully open door.
2. Starting at corner, pull gasket away
from door.
3. Continue to pull gasket free from
gasket channel.
4. Upon removal, lay gasket down on a
ÀDWVXUIDFH
5. Partially loosen the 3 screws, securing the top hinge to
the cabinet.
6. Align the panel with the outside edge (opposite the
hinge) and high enough to align with the highest point
in the door.
7. Insert panel underneath top hinge and apply upward
pressure while bringing the lower portion of the
SDQHOÀXVKWRWKHGRRULQVLGHWKHORZHUKLQJH7KH
SDQHOZLOO¿WVQXJJO\
$OLJQGRRUZLWKFDELQHW7LJKWHQWKHWRSVFUHZV
securing the top hinge to the cabinet.
'XHWRGLႇHUHQFHVLQÀRRUFRQVWUXFWLRQRUVXUURXQGLQJ
FDELQHWU\WKHSDQHOPD\QRWVLWÀXVKZLWKWKHWRSRIWKH
door.
Align Panel
Against
Door/Drawe
Edge First
Align Top Of Panel With Highest Point Of Door/Drawe
r
NOTE
Door
Panel
9. Secure integrated
panel to door/drawer
using clamps. A robust
tape may also be used.
Marvel recommends
the use of bar clamps
to secure the panel to
the door. If using tape,
be certain the tape will
not damage panel
¿QLVKXSRQUHPRYDO
10. Using a 7/64" drill
bit, drill 6 pilot holes into
the wood panel 1/2"
deep using the holes
in the door frame as a
guide.
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood when
hardwood is installed.
11. Locate 6 of the #6x 1-1/4" screws provided with your
unit.
th d /d f
Wood
Panel
Door/Drawer
Bar
Clamp
Bar
Clamp
NOTE
5

11. Locate 6 of the #6x 1-1/4" screws provided with your
unit.
12. Using a Phillips screwdriver, place one screw
into each of the 6 pilot holes and screw down. Do not
overtighten screws.
13. Be sure the screws force their way past the opening
RQWKHJDVNHWFKDQQHODQGVLWÀXVKDJDLQVWWKHERWWRP
of the channel.
14. Remove clamps from door.
If panel requires additional adjustment after removing
clamps, slightly loosen each screw and adjust panel as
QHFHVVDU\7LJKWHQVFUHZVXSRQFRPSOHWLRQ
15. Starting at the corners, reinstall the gasket into the
gasket channel in the frame. Make sure the gasket is
IXOO\VHDOHG7KLVPD\WDNHVRPHIRUFH
Integrated Panel Inte
g
rated Panel
NOTE
INTEGRATED PANEL INSTALLATION
6