MasterChef 043-1037-6 User manual

2-in-1 ESPRESSO MAKER AND MILK FROTHER
Model no. 043-1037-6
Read this booklet thoroughly before using the product, and save it for
future reference.
TM
INSTRUCTION MANUAL

Model no. 043-1037-6 | Contact us: 1-855-803-9313
2
able of ContentsTable of Contents
IMPORTANT SAFETY INSTRUCTIONS
Before using electrical appliances, basic safety precautions should always be followed
including the following:
1. Read all instructions before using. Save these instructions for future reference.
2. Check that the voltage of wall outlet corresponds to rated voltage marked on
the rating plate.
3. This appliance has a polarized plug (one blade wider than the other). To reduce the risk of
electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug
does not fit fully into the outlet, reverse the plus. If it still does not fit, contact a qualified
electrician. Do not attempt to modify plug in any way.
4. To protect against fire, electric shock and injury to persons do not immerse cord, plug in
water or other liquid.
5. Remove plug from power outlet before cleaning and when not in use. Allow appliance to
cool down completely before removing or attaching components or before cleaning.
6. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest
authorized service facility for examination, repair or electrical or mechanical adjustment.
7. The use of accessory attachments not recommended by the appliance manufacturer may
result in fire, electric shock or injury to persons.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS 2
KNOW YOUR ESPRESSO MAKER 4
BEFORE THE FIRST USE 4
PREHEATING 5
MAKING ESPRESSO 5
MAKING CAPPUCCINO 6
PRODUCING STEAM TO HEAT LIQUIDS OR BEVERAGES 7
CLEANING AND MAINTENANCE 7
CLEANING MINERAL DEPOSITS 8
ENVIRONMENT FRIENDLY DISPOSAL
WARRANTY
9
10
TROUBLESHOOTING 8
Table of Contents

3
8. Place appliance on flat surface or table, do not hang power cord over the edge of a table
or counter.
9. Ensure the power cord does not touch the hot surface of the appliance.
10. Do not place the espresso maker on a hot surface or beside fire in order to avoid damage
to the product.
11. To unplug, remove plug from power outlet. Always hold the plug. Never pull the
cord.
12. Do not use appliance for other than its intended use.
13. Close supervision is necessary when your appliance is being used near children.
14. Avoid contact with steam as this may cause serious injury.
15. Do not touch the hot surface of the appliance (such as steam wand, and the steel mesh
just after
ter
boiling). Use handle or knobs.
16. Do not let the espresso maker operate without water.
17. Do not remove the metal funnel when appliance in brewing coee or when steaming.
18. Insert plug into power outlet before starting espresso maker. Before unplugging from
power outlet, ensure all switches are turned off.
19. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliances by a
person responsible for their safety.
20. Children should be supervised to ensure that they do not play with the appliance.
21. The environment temperature of operating or storing should be more than 0°C (32°F).
22. This appliance is intended to be used in household and similar applications such as:
– Sta kitchen areas in shops, oces and other working environments;
– Farm houses;
– By clients in hotels, motels and other residential type environments;
– Bed and breakfast type environments.
23. Do not use outdoors.
24. Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
TM

Model no. 043-1037-6 | Contact us: 1-855-803-9313
4
Water tank cover
Detachable water tank
Operation knob
Froth device
Steam tube
Power switch
Coffee/steam switch
Metal funnel
(with mesh)
(Red indicator)
(Green indicator)
Removable cup sh elf
Drip tray
KNOW YOUR ESPRESSO MAKER
(Product may be subject to change without prior notice)
KNOW YOUR ESPRESSO MAKER
NOTES ON THE CORD
Notes onthe cord plug
This appliance has a polarized plug. To reduce the risk of electric shock, this plug is
intended to fit into a polarized outletonly one way. If the plug does not fitfully into
the outlet, reverse the plug. If itstill does not fit, contact a qualifiedelectrician. Do
not attempt to modify the plug inany way.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY

BEFORE THE FIRST USE
BEFORE THE FIRST USE
To ensure the first cup of coee tastes excellent, you should rinse the espresso maker with water as
follows:
1. Pour water into water tank, the water level should not exceed the “MAX” mark in the tank. Then
close the water tank cover.
3. Place an espresso cup on the removable cup shelf. Make sure the operation knob is on the“ ”
position.
4. Plug appliance into power outlet, press the power switch to the lower “ ” position.
The power indicator will be illuminated. The appliance will start heating.
5. Press down the Coee/steam button to the higher position which is the “ ” position, waiting a few
seconds
until the ready indicator turns on which indicates pre-heating is finished. Turn the
operation knob to the “ ” position. The water will flow out.
NOTE:
The appliance is supplied with a detachable tank for easy cleaning. You can fill the
tank with water first and then replace tank onto the appliance.
NOTE:
The appliance is not equipped with a jug or coffee pot. Please use your jug or coee
cup.
2. Setsteel mesh into metal funnel (do not add ground coee yet) , make sure the tube on the
with groove in the appliance, theninsertthe funnel into the appliance from the
“INSERT/” position.
”
position.
funnel aligns
INSÉRERLock funnel into place firmly by turning it counter-clockwise
5
TM
NOTES ON THE CORD
BEFORE THE FIRST USE
Notes onthe cord
a) A short power-supply cord (or detachedpower-supply cord) is provided to reduce
risks resultingfrom becoming entangled in or tripping over a long cord.
b) Longer detachable power-supply cords or extension cords are available and may
be used if care is exercised in their use.
c) If a long detachable power-supply cord or extension cord is used:
1) The marked electrical rating of the detachable power-supply cord or extension
cord should be at leastas great as the electrical rating of the appliance.
2) The longer cord should be arranged sothat it will not drape over the counter
top or table top where it can be pulledon by children or tripped over.
3) If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord.

PREHEATING
6. After about one minute, turn the operation knob to the “ ” position to stop brewing. Pour out the
water and clean espresso maker. Now you can start brewing.
PREHEATING
To make a cup of good hot Espresso coee, we recommend you preheat the appliance before
making coee, including the funnel, steel mesh and cup, so that the coee flavour can not be
influenced by the cold parts.
1. Remove the detachable tank and open the tank cover to fill it with desired water. The water level
should not exceed the “MAX” mark in the tank. Place the tank into the appliance properly.
2. Set steel mesh into metal funnel (without ground coffee), make sure the tube on the funnel
aligns with groove in the appliance, then insert the funnel into the appliance from the “INSERT/
INSÉRER” position. Lock funnel into place firmly by turning it counter-clockwise
until it is at the
“” position.
3. Place an espresso cup on the removable cup shelf.
4. Plug appliance into power outlet. Make sure the operation knob is on the “ ”
position.
5. Press down the button . The red indicator will be illuminated.
6. The appliance will start heating.
7. Press down the Coee/steam button to the higher “ ” position, waiting a few seconds until
the ready indicator turns on, which indicates pre-heating is finished.
MAKING ESPRESSO
1. Remove the metal funnel by turning it in clockwise, set steel mesh into metal funnel. Add ground
coffee to steel mesh with measuring spoon, a spoon of ground coffee makes about a cup of
top-grade coffee. Press the ground coffee tightly with the tamper.
2. Insert the funnel into the appliance from the “INSERT/INSÉRER” position and release the press bar.
Lock funnel into place firmly by turning it counter-clockwise until it is at the “ ”
position.
3. Pour out the water that is released into the cup. Then place the warmed espresso cup on the
removable cup shelf.
NOTE:
There may be noise when pumping the water the first time. This is normal.The
appliance is releasing the air from the appliance. After about 20 seconds, the noise
will disappear.
MAKING ESPRESSO
Model no. 043-1037-6 | Contact us: 1-855-803-9313
6

NOTE: When brewing coee or making steam, it is normal that the green
indicator is likely to turn off. This means that the heater is heating up to keep
the temperature at the standard range.
NOTE: When making steam, the metal funnel must be assembled in position.
NOTE: When choosing the size of the container, it is recommend that the diameter
is not less than 70 mm. As the milk will increase 2 times the volume, ensure the
height of jug is enough.
MAKING CAPPUCCINO
Make cappuccino by topping up a cup of espresso with frothy milk.
Method:
1. Prepare espresso first with container large enough according to instructions in 'MAKING ESPRESSO'.
Ensure that the operation knob is at the “ ”.
2. Press the coee/steam switch to lower position which is the position, and wait for the ready
indicator to illuminate.
3. Fill a container with about 100 g (3 1/2 oz) of milk for each cappuccino to be prepared. It is
recommended to use whole milk at refrigerator temperature (not hot!).
4. Insert the froth device into the milk about 2 cm (3/4"). Turn the operation knob to the
“ ” position, steam will be released from the steam outlet. Froth milk while moving the container
around and up and down.
5. When the desired froth is reached, you can turn the operation knob to the “ ” position.
4. When the ready indicator is illuminated, turn the operation knob to the “ ” position. The
coee will flow out.
5. Turn the operation knob to the " " position when desired coffee is obtained or when the colour of
the coffee changes. Press power switch and the power indicator and ready indicator will turn off and
the espresso maker will stop brewing.
6. When you finish making espresso, remove the metal funnel by turning it clockwise. Pour the coee
residue out with the steel mesh pressed by press bar.
7. Let funnel and mesh cool down completely, then rinse under running water.
WARNING: Do not leave the espresso maker unattended during making the coee, as
manually operation may be required.
MAKING ESPRESSOMAKING CAPPUCCINO
7
TM

PRODUCING STEAM TO HEAT LIQUIDS OR BEVERAGES
CLEANING AND MAINTENANCE
NOTE: Do not clean with alcohol or solvent cleanser. Never immerse the housing
in water for cleaning.
NOTE: Clean steam outlet with wet sponge immediately after steam stops being
produced. Use caution as steam outlet may be hot!
NOTE: After making steam, it is recommended that you allow the espresso maker
to cool down for at least 5 min before making espresso again. Otherwise a burnt
odour or taste may be noticed in your espresso.
r in
PRODUCING STEAM TO HEAT LIQUIDS OR BEVERAGES
The steam wand can be used to heat beverages such as tea, hot chocolate or water.
Method:
1. Remove the detachable tank and fill it with desired water. The water level should not exceed the
“MAX” mark in the tank. Place the tank into the appliance properly.
2. Plug appliance into power outlet. Press the power switch to the lower position, and the
power indicator will illuminate.
3. Press the coee/steam switch to the higher position which is the position, and waitt until the
ready indicator is illuminated.
4. Dip the steam wand without froth device sleeve into the liquid to be heated or the intended froth
milk. Turn the operation knob to the “ ” position.
5. When the required temperature is reached, you can turn the operation knob to the “ ” position.
6. Press the power switch to the “ ” position to shut o the power source.
6. Pour the frothed milk into the prepared espresso, and now your cappuccino is ready. Sweeten to
taste and if desired, sprinkle the froth with a little cocoa powder.
7. Press the power switch to the higher position to shut o the power source.
CLEANING AND MAINTENANCE
1. Shut off the power source and let the espresso maker cool down completely before cleaning.
2. Clean housing of espresso maker with a moisture-proof sponge often and clean water tank, drip tray
and removable shelf regularly. Dry completely.
3. Detach the metal funnel by turning it clockwise. To remove coffee residue inside, clean with a
cleanser and rinse with clean water.
4. Clean all the attachments in water and dry thoroughly.
Model no. 043-1037-6 | Contact us: 1-855-803-9313
8

TROUBLESHOOTING CLEANING MINERAL DEPOSITS
TROUBLESHOOTING
3. Using the program of pre-heating, put the metal funnel (no ground coffee inside) and a container
in place. Brew water per “ PRE-HEATING”.
4. Press the power switch to the lower position which is the “ ” position. The power indicator will
be illuminated. The appliance will start heating.
5. Press down the Coee/steam button to the higher position which is the “ ” position, waiting a few
seconds, until the ready indicator turns on which indicates pre-heating is finished.
6. Turn the operation knob to the “ ” position and make two cups of espresso (about 2 oz / 1/3 cup).
Then turn it to the“ ” position.
7. Press the coee/steam switch to the lower position which is the position, waiting a few seconds
until the ready indicator is illuminated. Turn the operation knob to the “ ”position and make steam
for 2 minutes, , then turn the operation knob to the “ ” position to stop making steam. Press the power
switch to the higher position to stop the unit immediately, and allow the descaler to remain in the unit
at least 15 minutes.
8. Restart the unit and repeat the steps of 4-7 at least 3 times.
9. Add tap water to the MAX level. Turn on the espresso maker (with no ground coffee) and brew.
Repeat steps of 4-7 three times (it is not necessary to wait for 15 minutes in step of 7), then brew
until no water is left in the tank.
Symptom
Water leaks from the bottom of
espresso maker.
Acid (vinegar) taste exists in
Espresso coffee.
There is a lot of water in the drip
tray.Please clean the drip tray.
The espresso maker malfunctions.
Espresso maker not properly
cleaned.
Ground coffee was stored in a hot,
damp place for a long time. Ground
coffee has turned bad.
Clean espresso maker following
steps in 'Before the First Use'
several times.
Please contact an authorized
service facility for repairing.
Cause Corrections
CLEANING MINERAL DEPOSITS
1. To ensure your espresso maker operates efficiently and coffee retains its peak flavour and the
internal piping is clean, the mineral deposits should be removed every 2 to 3 months.
2. Fill the tank with water and descaler to the MAX level (the scale of water and descaler is 4:1, the
detail refers to the instructions on the descaler. Please use “household descaler”, you can use the citric
acid (obtainable from a chemist’s or a drug store) instead of the descaler (the one hundred parts of
water and three parts of citric acid).
Always use fresh ground coee.
Store unused ground coee in a
cool, dry place. Reseal open
packages and store in refrigerator
to maintain freshness.
9
TM

TROUBLESHOOTING
Environment friendly disposal
The steam cannot froth.
Coffee overflow .
The container is too big or the shape
does not fit.
You have used skimmed milk.
Espresso maker has not been
cleaned for long time .
Brew coffee immediately after
steam releasing.
Use whole milk or half skim
milk.
After daily use, brew 2 cups water
to clean residue in espresso
machine.
Use a tall and narrow cup.
The ready indicator is not
illuminated.
Only after the ready indicator is
illuminated, the steam can be
used to froth.
Do not disasemble the appliance. If the cause of failure is not found, contact a certified service
centre.
The espresso maker does not work. Espresso maker not plugged in. still does not work, please
contact with the authorized
service facility for repairing.
You can help protect the environment! Please remember to respect
the local regulations: dispose of as per the requirements of your local
municipality.
Environment friendly disposal
Plug the power cord into a power
outlet correctly. If the appliance
Do not brew coee immediately
after steaming. If you want to
make espresso, follow the brewing
process until the indicator light
turns o. To brew more espresso,
pre-heat until the indicator light
turns green.
Model no. 043-1037-6 | Contact us: 1-855-803-9313
10