Matco Tools MWLFL3000 User manual

INSTRUCTION MANUAL
36W SMD
Rechargeable Site Lamp
72 SMDs lights
with 3 intensity
modes
Foam grip
on handle for
comfort
Robust & durable
aluminium
housing
Strong powder
coated steel
stand
IP65
WATER & DUST
PROOF RATING OPERATING TEMPERATURE
-10°C TO 40°C
(-14°F TO 104°F)
SIZE (LÐHÐD)
(INCH) (MM)
8.7 x 8.7 x 12.2 223 x 223 x 309
3 LED battery level indicator
5V 2.1 Amp USB output port for use
as powerbank
Power
Button
USB
Port
360°
Rotation
CHARGING OF BATTERY
Battery can be recharged using dual voltage
AC 100V-240V AC charger, provided with the
light
Charge Time
4.5 hours
LITHIUM-ION
RECHARGEABLE
RECHARGEABLE
BATTERY
7.4V 4400 mAH
Multi-mode super bright
36W 72 SMD site lamp
Light Output
Single button controlled high quality
output in multiple modes
HIGH
INTENSITY
MEDIUM
INTENSITY
LOW
INTENSITY
LUMEN 3000 1500 750
RUN TIME 1.5 hours 2.5 hours 5 hours
STURDY CONSTRUCTION
a. Protected against dust and eects
of low pressure water jets from
any direction
b. Corrosion resistant aluminium
die cast construction in premium
powder coated finish
c. Impact proof ABS frame
d. Tempered glass lens
e. Steel handle with foam grip for
comfort in use
f. Sturdy steel stand for balance
positioning in the toughest of job
site conditions
PATENTED DESIGN
Unique & innovative 360° swivel & tilt
mechanism. Stainless steel ball joint
mechanism allows
a. Swivelling to full 360°
b. Tilt
POWER SOURCE
RoHs
LED 660 - Neutral Rev_B.indd 1LED 660 - Neutral Rev_B.indd 1 18/09/20 11:35 AM18/09/20 11:35 AM

2
SAFETY INFORMATION
• Follow workshop health & safety rules,
regulations and conditions when using the
rechargeable site lamp.
• When not in use, rechargeable site lamp
should be stored in a dry location to inhibit
rust.
• During their period of use, accessories must be
checked for wear, cracks and other damage,
replace any damaged or worn parts.
• Use genuine parts only. Unauthorized parts
may be dangerous and will void the warranty.
• Keep the rechargeable site lamp clean and
in good working order for best and safest
performance.
• DO NOT use the lamp in the immediate vicinity
of inflammable materials or gases.
• DO NOT point the light directly in your own or
any other person’s or animal’s eyes.
• DO NOT pull the charger plug from the mains
socket by the lead.
• DO NOT drop, throw or abuse the
rechargeable site lamp.
WARNING!
• DO NOT use any other type of charger with
this product, other than the supplied mains
or car charger. Failure to observe this warning
could result in injury and or fire and will void
the warranty.
PACKAGING CONTENT
DESCRIPTION QTY.
Rechargeable site lamp 1
Universal AC Adaptor 1
O.I.P.M. 1
BEFORE INSTALLATION
• Eyes protection: Wear a protective mask or
protective eyewear.
• Check that the product has not suered any
damage during transport or storage. Clean and
remove any dust or residual packing material.
• Read the instructions carefully before using
rechargeable site lamp and keep them for
further reference.
WARNING!
• Defective accessories can lead to personal
injury and material damage.
INSTALLATION
Refer “EXPLODED VIEW”
1. Place the site lamp on a plane surface and
open the charging socket cover (11) located on
the rear of the light just below the switch (8).
2. Connect charging lead to the socket in the
back of light. Connect charger to power
supply, switch on power supply. The battery
will begin charging, full charge will be reached
in approx. 4.5hrs.
3. The three LED lights near the charging socket
cover (11) shows the state of charge of the
battery while charging.
4. When the battery is fully charged, remove the
charger and close the charging socket cover
(11). (A USB port is also position next to the
charging connection so that the battery can be
used as a power bank.)
CAUTION!
• Use only the supplied charger plug for
connecting lamp to the power supply.
• DO NOT turn the lamp on when it is being
charged.
• DO NOT attempt to open, disassemble, modify
or service the battery pack.
• DO NOT expose rechargeable site lamp to
temperatures above 60°C (140°F).
• DO NOT use the lamp if you suspect that the
battery or the lamp casing is damaged.
• DO NOT leave battery in a discharged state,
recharge battery immediately. Before storage,
fully recharge the battery, subsequently
recharge the battery at least once every six
months of non-use.
OPERATING INSTALLATION
(Refer “EXPLODED VIEW”)
1. Press the switch (8) once for low, twice for
medium and three times for high lumens
output.
2. The site lamp can swivel through 360° and be
tilted
MAINTENANCE
• Recharge the battery immediately when
discharged.
• Before storage, fully recharge the battery,
subsequently recharge the battery at least
once every six months of non-use.
• When not in use, rechargeable site lamp
should be stored in a dry location.
LED 660 - Neutral Rev_B.indd 2LED 660 - Neutral Rev_B.indd 2 18/09/20 11:35 AM18/09/20 11:35 AM

3
EXPLODED VIEW
PART LIST
REF NO. DESCRIPTION QT Y.
1Front housing 1
2Tempered glass 1
3Sealing ring 1
4Plastic Reflector 1
572 LED PCB 1
6Mains housing 1
7Handle 1
8Switch 1
9Switch cap 1
10 Back housing 1
11 Charging socket cover 1
12 Waterproof ring 1
12345
6
7
89
10
11
12
13
14
15
16
17
18
19
20
21
22
23
REF NO. DESCRIPTION QTY.
13 7.4v (4400 mAh) battery pack 1
14 Battery cover 1
15 Indicator support 1
16 PCB 1
17 "X" stand 1
18 Rubber cap 4
19 Bottom Ball solid board 1
20 Rotating support 1
21 Pivot 1
22 Ball middle solid board 1
23 Wave spring 1
LED 660 - Neutral Rev_B.indd 3LED 660 - Neutral Rev_B.indd 3 18/09/20 11:35 AM18/09/20 11:35 AM

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The rechargeable site lamp has low lumen output
or does not work.
Low battery Recharge the battery
If the rechargeable site lamp still doesn't work Contact nearest authorized service dealer
DISPOSAL
The components or the used products must be given to companies that specialize in the disposal and
recycling of industrial waste.
TROUBLE SHOOTING
LED 660 - Neutral Rev_B.indd 4LED 660 - Neutral Rev_B.indd 4 18/09/20 11:35 AM18/09/20 11:35 AM