Matsui DTR1 User manual

DTR1
Free to View Digital TV Receiver
USER MANUAL

SAFETY
POWER
The receiver should be plugged into a 230V to 240V AC, 50Hz supply only
LEADS
Ensure the power supply lead, and all other leads, are positioned so they are not likely to be walked on or
pinched by things placed on or against them Pay particular attention to the power lead, where it enters the
mains plug and where it comes out of the receiver Do not connect or adjust leads when the receiver is plugged
in
TEMPERATURE AND MOISTURE
Do not leave or use the receiver in a hot, cold or humid area Do not allow the receiver to get wet - from
drips or splashes - as this may be dangerous Do not place water-filled objects such as flower vases, on
top of the receiver
VENTILATION
Slots and openings in the receiver's cover are for ventilation Do not cover or block them as this could lead
to overheating
CLEANING
Unplug the receiver before it is cleaned Use a lightly dampened cloth only Do not use liquid or aerosol
cleaners
HEAT AND FLAMES
The receiver should not be placed near to naked flames or sources of intense heat, such as an electric fire
Ensure that no naked flames sources, such as lighted candles, are placed on top of the Receiver
LIGHTNING
Unplug your receiver from the wall socket if there is a storm or lightning, or if it is to be unused for a long
time
REPLACEMENT PARTS
If your receiver needs a replacement part, ensure the person undertaking the repair uses parts which are
specified by the manufacturer or have the same specifications as the original part Other parts may cause
a fire, electric shock or other hazards
BATTERY DISPOSAL
Please ensure that exhausted batteries from the remote control handset are disposed of safely
SERVICING
Ensure the person who services your receiver is qualified to do so Do not remove the cover yourself - you
could get an electric shock
We are proud to offer a high-quality product To keep this level of quality, your receiver should be serviced
at a Matsui authorised service centre

CONTENTS
l Safety
l Co te ts
l Remote Co trol Ha dset 1
l Your Digital Receiver 3
l Everyday Operatio 4
- Cha gi g Cha els 4
- Cha el List 5
- Electro ic Programme Guide 6
- Audio Co trol 7
- Digital Teletext 7
- Widescree 8
l Adva ced Operatio 9
- Co figuri g Your Receiver 9
- Editi g The Cha el List 10
- Cha el A d Me u Protectio 11
- Favourite Cha els 12
- Programme Remi ders A d Timers 12
- Re-i stallatio 14
l Over Air Dow load 15
l Co ecti g a VCR or DVD (with o e scart socket) 16
l Co ecti g a VCR a d DVD (with two SCART sockets) 17
l Troubleshooti g Guide 18
l Specificatio 19

REMOTE CONTROL HANDSET
79'79
6WDQGE\
1XPHULF
:LGH
3URJUDPPHXS
3URJUDPPHGR Q

9ROXPHXS
9ROXPHGR Q

,QIR+HOS
3DJHXS5HG
8S
/HIW
3DJHGR Q*UHHQ
([LW
6XEWLWOH
0XWH
*XLGH
0HQX
%OXH
5LJKW
'R Q
6HOHFW
<HOOR 
7H[W 
-1-

REMOTE CONTROL HANDSET
REMOTE BUTTONS
Butto Fu ctio
1 Sta dby Turn the receiver on and off
2 Mute Silence received audio
3 TV/DTV Exit most menus to return to television viewing
Switch the TV set between analogue, digital TV and VCR
4Meu Display the Main Menu Exits menus
5 Up, Dow , Left, Right Move between menu items
6 Select Make selection in a menu
7 Number keys Change channels
Enter PIN code
Enter numbers and letters into menus
8 Guide Display and exit electronic programme guide
9 V+, V- Adjust the received audio volume
10 P+, P- Change channels
11 Page Up/Red Move up a page through channel list
Move to top in EPG programme details
Select red option in digital teletext
12 Page Dow /Gree Move down a page through channel list
Select green option in digital teletext
Move to bottom in EPG programme details
13 Yellow Scroll up through EPG programme details
Select yellow option in digital teletext
14 Blue Scroll down through EPG programme details
Select blue option in digital teletext
15 Wide Select screen format
16 i Display menu help
17 Text Start and stop digital teletext
18 Exit
-2-

YOUR DIGITAL RECEIVER
Fro t:
6WDQGE\ 'LVSOD\
3URJUDPXS
&XUVRUXS
3URJUDPGRZQ
&XUVRUGRZQ
Rear:
$17,1 79287 56
6&$5779 6&$579&5$8;
5(6(7
$&9
+]
PD[:
a
/
5
$8',2
$QWHQQDLQ
79RXW
56VRFNHW
796&$57VRFNHW
9&56&$57VRFNHW
$8',2RXWSXW
/HIW5LJKW
5HVHW
-3-

EVERYDAY OPERATION
While using your Matsui DTR1 receiver to the full
there are great many keys to use in different
situations Many of the menu screens displayed by
the receiver have reminders as to which keys do
what, at the base of the screen In addition, many
screens have further help available which is
displayed when the [i] key is pressed, as prompted
at the bottom right of the screen
Providing your TV set SCART socket has switch
control, pressing the [TV/DTV] key at any time while
watching television programmes will switch the TV
set between displaying the digital terrestrial
television programme and its normal analogue
television reception
CHANGING CHANNELS
You can select the channel you wish to watch in one
of four ways - stepping through the channel list,
selection by number, from the on-screen channel
list, and using the electronic programme guide
(EPG)
To move through the channel list, press the [P+] or
[P-] keys on the remote control Pressing the [P+]
key will select the channel next in the channel list
Pressing the [P-] key will select the previous channel
in the list
Pressing the [P+] key when the last channel in the
list is being viewed will select the first channel
Similarly, pressing the [P-] key when the first
channel is displayed will select the last channel in
the channel list
You can also select the required channel using its
channel list number Channel numbers are entered
using the number keys on the remote control
handset and can be up to three digits long
Hint
The channel list numbers are assigned by the
broadcasters. Because not all channels are
broadcast free-to-air and stored by the receiver,
the channel list numbers do not run
continuously. The fifteenth channel in the list,
for example, may not be channel number 15 but
channel number 17.
When you press a number key on the remote
control, a small box appears in the top left of the
screen to show the entered number After each digit
is entered, the receiver will wait up to two seconds
for the next digit to be pressed until either three digits
have been entered or you do not press a digit in time
The channel corresponding to the entered number
in the box will then be selected
Hint
f you enter a number which does not
correspond to a stored channel, the next valid
channel number is selected instead. f you enter
a number greater than the highest numbered
channel in the channel list, the receiver will
select the last channel in the list.
I formatio Ba er
Whenever you change channel, using the [P+] and
[P-] keys or the number keys, the receiver displays
the channel picture along with an information banner
at the bottom of the screen This will remain on the
screen for approximately three seconds The
information banner can also be displayed at any
time while watching TV by pressing the [i] key on the
remote control Pressing the [i] key again removes
the banner
Hint
Not all channels broadcast the programme
data. f the name and times of the programme
is not available then 'Not available' is displayed
in the information banner.
The information banner gives a number of facts on
the channel selected and the programmes on it The
name of the channel is displayed, along with its
channel list number and an indication of the strength
of the signal received on this tuning channel
The name and the start and finish time of the
programme currently showing on the selected
channel are given, and the current time
-4-

Icons are also displayed in the information banner
and if this channel is a favourite channel (see
ADVANCED OPERATION - Favourite Channels)
favourite channel
If the channel selected is locked (see ADVANCED
OPERATION - Channel Protection), you must enter
the correct four digit code to view the channel
Alternatively, the [P+] or [P-] keys are used to move
to another, unlocked channel

CHANNEL LIST
You can also select the required channel directly
from the on-screen channel list This is displayed
using the Matsui DTR1 receiver's Main Menu First
bring up the menu with the [MENU] key on the remote
control handset
Using the [UP] or [DOWN] keys on the remote
control, make sure that the first item, Channel List,
is highlighted in yellow and press the [SELECT] key,
to display the channel list
6(/(&7
L
Here, you can preview any channel stored by the
receiver before viewing it full screen The complete
list of channels is displayed in pages of 10 channels
at a time, with their channel list number and a
favourite channel icon if appropriate (see
ADVANCED OPERATION - Favourite Channels)
The name and a quarter-screen image of the
channel last viewed is displayed in the top right of
the screen
Using the [UP] or [DOWN] keys, the highlight is
moved through the list to the channel required The
[PAGE UP] and [PAGE DOWN] keys can also be
used to move forward or back a complete page (ten
channels) at a time Pressing [SELECT] now
changes the quarter-screen display to show the
highlighted channel
Hint
From the Channel List screen, it is possible to
edit the channel list, including changing the
name of stored channels or deleting them.
Editing the list is covered in ADVANCED
OPERAT ON - Editing The Channel List. When
using the Channel List to select channels, use
the [LEFT] or [R GHT] keys to ensure that the
highlighted button at the bottom of the screen
is SELECT, so no editing functions are
accidentally begun.
When you leave the Channel List screen, by
pressing [MENU] the channel showing on the quarter
screen is selected for normal viewing on the whole
screen
-5-

ELECTRONIC PROGRAMME GUIDE
The fourth way of selecting a channel is with the
electronic programme guide, or EPG The EPG is
accessed by pressing the Guide key, [GUIDE] Like
the Channel List, the EPG screen displays a list of
the stored channels (in pages of five channels)
along with information on what programmes are being
broadcast
6(/(&7
L
Curre t Programme
The channels are listed at the bottom of the screen,
each with the 'current event' (the name of the
programme showing at that time) and the 'next
event' (the following programme) When the EPG
screen is first displayed, the channel last watched
is highlighted in the list of channels A quarter-screen
image of this channel is displayed at the top right
of the screen along with the channel name and
channel list number
Details of the current programme on that channel
(the name of the programme and, typically, a
synopsis with details of the stars involved, the
teams playing, or similar information) along with the
start and finish times are displayed at the top left
inside the dark blue text window
Hint
f the channel you have been viewing is a digital
teletext channel then no picture will appear in
the quarter-screen window.
Moving the highlight through the list of channels
using the [UP] and [DOWN] keys will change the
programme details in the text window to reflect the
channel highlighted The quarter-screen window
continues to show the channel last watched, so you
can stay watching a programme while at the same
time browse the details of what's on, on other
channels
You may then select the highlighted channel for
viewing on the quarter-screen window by pressing
the [SELECT] key
You can leave the EPG screen, to enjoy normal full-
screen viewing of the channel in the quarter-screen
window by pressing the [GUIDE] key again, or the
[MENU] key
Hint
Not all channels broadcast all the programme
information data. Some channels do not
provide the current and next event data and/or
the programme details. n this case the
programme names and/or the details are not
displayed. This is not a fault with your receiver.
Next Programme
While the EPG screen is displayed, pressing the
[RIGHT] key highlights, in dark blue, the next event
name in the list of channels and displays the
highlighted channel's programme details for the next
event (the programme following the current
programme) in the text window As before, you can
browse through the list, checking the programmes
coming up next on all the channels
Hint
f the programme details text for the current or
next event is too long to fit into the text window
on the EPG screen, a scroll bar appears on the
right hand side of the window and the text can
be scrolled up or down using the [YELLOW] and
[BLUE] keys on the remote control. Using [PAGE
UP] or [PAGE DOWN] keys will display the next/
previous 5 channels in the list.
6(/(&7
L
-6-

Pressing the [SELECT] key while the next event
details are displayed will set a reminder to watch that
programme See ADVANCED OPERATION -
Programme Reminders And Timers
You can return to the current programme display by
pressing the [LEFT] key or to normal television
viewing (to watch the channel last selected in the
EPG screen) by pressing the [GUIDE] key again,
or the [MENU] key
AUDIO CONTROL
Volume Co trol
The volume level of the sound from your Matsui
DTR1 receiver can be altered with the [V+] and [V-
] keys on the remote control handset Pressing
either key displays a bar graph of the sound volume
on the TV screen
The volume level selected will remain set, even when
the receiver is turned off and on again, until it is
altered with the [V+] and [V-] keys
Hint
The audio volume adjustment for the DTR 1
receiver is independent of the volume control
on your TV set. Be careful that both volume
controls are kept within reasonable levels so
that when switching from analogue to digital
television viewing, or when first turning on your
TV set, the sound level is not suddenly very
high.
You can silence the sound from the receiver by
pressing the [MUTE] key The sound remains muted
until the [MUTE] key is pressed again, the [V+] or
[V-] keys are pressed, or until the receiver is turned
off and on again
While the sound is muted in this way, the mute
symbol is displayed in the top left of the TV screen
The symbol is removed after 3 seconds, but the
sound will remain muted until the [MUTE] key is
pressed for the second time, and the un mute
symbol will display for 3 seconds
Sou dtrack La guage
Some programmes are broadcast in two or more
languages simultaneously The language heard can
be selected from the Language Menu Press
[MENU] to display the Main Menu and use the [UP]
or [DOWN] keys to highlight the Language line and
press [SELECT] Use the [UP] or [DOWN] keys to
highlight the soundtrack language required and press
[SELECT] Normal viewing, with the required
language soundtrack, can be resumed by pressing
the [MENU] key
If the programme has no alternative language
soundtrack broadcast, the Language Menu will not
be available, but a message, 'No Multi Language
Available' is displayed briefly
DIGITAL TELETEXT
Many digital terrestrial television channels not only
broadcast pictures and sound for programmes but
also pages of information on the programmes, the
weather, news and many other topics This digital
teletext can be displayed by the Matsui DTR1
receiver
Some channels are entirely given over to digital
teletext and carry no normal TV programme at all
These dedicated digital teletext channels will not give
a quarter-screen image in the EPG or the Channel
List screen When such a channel is selected, after
a brief pause, they will usually display the opening
page of information automatically
Other channels have digital teletext pages
broadcast alongside the television programme and
often include a reduced-size broadcast picture within
digital teletext pages These usually require the
[TEXT] button to be pressed to activate the digital
teletext pages
In both cases, moving through the different pages
of information is accomplished in a variety of ways,
dependent on the individual broadcasters, but
including use of the [UP], [DOWN], [LEFT],
[RIGHT] and [SELECT] keys to select items from
on-screen menus, and the coloured keys to jump
directly to particular pages
You can exit any digital teletext channel by changing
channel in any of the normal ways You can leave
the digital teletext function of a combined digital
teletext/programme channel, to return to normal
television viewing of that channel, by pressing the
[TEXT] key
-7-

Hint
Calling for the information banner or any menu
on-screen stops the receiver from displaying
the digital teletext pages and they are
temporarily replaced by a blank picture while
the banner or menu is displayed.. Digital
teletext cannot be accessed when the Subtitles
are enabled (See ADVANCED OPERAT ON -
Configuring Your Receiver.
WIDESCREEN
TV sets are available with screens of the standard
(4:3) format and widescreen (16:9) format When
you first installed your DTR 1 receiver you
specified the format of the connected TV (this can
now be altered if necessary; see ADVANCED
OPERATION - Configuring Your Receiver)
Digital terrestrial television broadcasts are also made
in both standard and widescreen formats In
particular, films and dramas tend to be broadcast
in widescreen format to closer emulate the cinema
experience, but even some news bulletins are
widescreen To help get the most from both TV set
and programme when a widescreen film is watched
on a standard TV, or a standard broadcast is viewed
on a widescreen set, your Matsui DTR1 receiver
includes the [WIDE] key
So long as the receiver has been correctly set up
for the TV set connected, a widescreen programme
will always be displayed correctly on a widescreen
set, and a standard format programme will correctly
fill the screen of a standard format TV
With a widescreen TV set displaying a standard
format programme, the [WIDE] key switches
between displaying the picture with black bars down
the sides, and enlarging the picture so that it fills the
whole width of the screen but the top and bottom are
cropped off
With a standard format TV displaying a widescreen
programme, the [WIDE] key switches between
displaying the picture with black bars at the top and
bottom of the screen, and filling the whole height of
the screen but cropping the sides off according to
instructions broadcast with the programme (called
'pan and scan')
The effect of the [WIDE] key on the picture display
is cancelled by pressing [WIDE] again, changing
channel or turning the receiver to standby
Subtitle
Subtitle key Shows/hides subtitles of channel When
the subtitle key is pressed, subtitle ON/OFF
message is displayed
TV / DTV Key
If there is no connected VCR device, The TV/DTV
key is used to toggle TV and DIGITAL TV modes
When the set-top box is in TV mode, the TV scart
is not switched and the TV operates in analog mode
When the set-top box is in DIGITAL TV mode, this
time the TV scart is switched on and the TV is
switched to AV/RGB mode And also, when there is
no menu on the screen , pressing TV/DTV key will
manually toggle the set top box between VCR mode
and TV mode In VCR mode set top box will display
the output of VCR device , In TV mode set top box
displays its own outputs If box scart mode is not
changed by pressing TV/DTV key , scart mode will
be automatically detected (For example if a dvd
player is connected to VCR scart and powered on
, then the set top box will immediately switch to VCR
mode The set top box will switch to TV mode if dvd
player is switched off )
-8-

ADVANCED OPERATION
CONFIGURING YOUR RECEIVER
Many aspects of your Matsui DTR1 receiver can
be set up to reflect your circumstances and
preferences The Configuration menu screen is
accessed from the Main Menu Press the [MENU]
key to display the Main Menu and the [DOWN] key
twice to highlight Configuration, then press
[SELECT] to display the Configuration menu screen
L
The various configuration functions are displayed
in a list, along with a quarter-screen image of the
currently selected channel You can select a
function by highlighting the corresponding menu line
with the [UP] or [DOWN] keys There are seven
configuration functions
Audio La guage
Digital terrestrial television channels can broadcast
simultaneous soundtracks in more than one
language This function selects which language
soundtrack you will hear when switching to a channel
broadcasting with multiple soundtracks See also
EVERYDAY OPERATION - Audio Control
Highlight the Audio Language line in the
Configuration menu and use the [LEFT] or [RIGHT]
keys to cycle through the language options
Return No Menu to normal TV viewing by pressing
the [MENU] key
SUBTITLE
Digital terrestrial television channels can broadcast
with subtitles displayed on-screen for the hard-of-
hearing This function selects the desired subtitle
language and enables the automatic display of
subtitles whenever subtitle information is broadcast
Highlight the Subtitle line in the Configuration menu
and use the [LEFT] or [RIGHT] keys to cycle
through the disable and language options
Return NO MENU to normal TV viewing by pressing
the [MENU] key
TV TYPE
Digital terrestrial television channels can broadcast
programmes in a widescreen format which must be
output differently to normal and widescreen TV sets
This function tells the receiver the screen format of
the TV connected so that broadcasts are displayed
correctly
Highlight the TV Type line in the Configuration menu
and use the [LEFT] or [RIGHT] keys to select 4:3
if you have a standard TV set connected or 16:9 if
it is a widescreen TV This function duplicates the
selection made at the time of first installation (see
1 - PREPARATION - Tuning In) and can be used if
you change TV sets Return NO MENU to normal TV
viewing by pressing the [MENU] key
TV OUT
The DVB-T receiver can output either an RGB or
CVBS signal from the TV SCART on the rear panel
Although the RGB format results in a better quality
picture, not all equipment - particularly some VCRs
- can cope with an RGB signal (see page 16
Connecting a VCR or DVD)
PARENTAL SETTINGS
This function enables or disables the menu protection
system and allows the PIN code to be changed See
ADVANCED OPERATION - Channel And Menu
Protection
-9-

EDITING THE CHANNEL LIST
The digital terrestrial television channels found by
the receiver when first installed are storedin its
memory as a channel list This list can be altered
and amended to remove unwanted channels and to
suit your own preferences
First bring up the Main Menu with the [MENU] key
on the remote control handset Then, using the [UP]
or [DOWN] keys on the remote control, make sure
that the first item, Channel List, is highlighted in
yellow and press the [SELECT] key, to display the
Channel List
6(/(&7
L
The Channel List screen displays the list of
channels in the receiver's memory, with a quarter-
screen image window showing the selected channel,
and can be used to change channels for viewing,
delete channels from the memory, edit the name of
the channel as it appears in the list and on-screen,
lock a channel against viewing by younger members
of the family, and set up favourite channels
Channel List functions are carried out on one
channel at a time The channel to be affected is first
highlighted in the list using the [UP] or [DOWN]
keys You can move faster through the list using
the [PAGE UP] or [PAGE DOWN] keys to move up
or down a complete page of 10 channels in one
jump
SELECT
This function selects a channel for viewing and is
an alternative to using the [P+] and [P-] keys,
channel number or EPG Highlight the channel to be
viewed, highlight the SELECT button at the base of
the screen using the [LEFT] or [RIGHT] keys and
press [SELECT] The highlighted channel now
appears in the image window and you can leave the
Channel List to view the channel by pressing
[MENU]
DELETE
The initial installation of the Matsui DTR1 receiver
can produce duplicate entries in the channel list
from transmitters operating at different frequencies
in adjacent areas, and you may wish to delete these
duplicate entries from the list In addition, other
channels which you do not want in the list
Highlight the channel to be deleted, highlight the
DELETE button at the base of the screen using the
[LEFT] or [RIGHT] keys, and press [SELECT] The
highlighted channel is deleted from the list
You can now perform further editing on the channel
list, or return to normal broadcast viewing by
pressing the [MENU] key
EDIT NAME
The channel names which appear in the channel list
and the information banner are assigned by the
broadcasters and some longer names are
abbreviated to become unrecognisable You can edit
the names to suit your preferences with the Edit
Name function
Highlight the channel to be renamed, highlight the
EDIT NAME button at the base of the screen using
the [LEFT] or [RIGHT] keys, and press [SELECT]
The highlighted channel name appears on the right
of the screen with the first character highlighted by
a cursor Any of the 15 characters that make up a
channel name can be highlighted using the [LEFT]
or [RIGHT] keys and the highlighted character
changed by pressing the [UP] or [DOWN] keys to
cycle through the alphabet, numbers and other
characters available
When the required changes have been made,
pressing [SELECT] stores the new name and returns
to the Channel List screen Alternatively, pressing
[MENU] will abandon the name change and return
to the previous name
You can now perform further editing on the channel
list, or return to normal broadcast viewing by
pressing the [MENU] key
Using the other two functions of the Channel List
menu screen - LOCK and FAVOU
-10-

Hint
You can also enter a channel name using the
number keys on the remote control. Each key
represents several letters and pressing a key
several times will enter each letter (in both
capitals and lower case), and the number, in
turn, in the character position marked by the
cursor. The zero key enters all the punctuation
marks available and a blank space. With
practise, this is a very quick means of entering
the required letters into the channel name.
CHANNEL AND MENU PROTECTION
CHANNEL LOCK
Some channels broadcast material which you do not
want younger members of the family to watch Any
channel can be 'locked' so that it cannot be selected
for viewing without first a four-digit PIN code being
entered In this way any channel not suitable for
younger viewers can be protected
The channel lock is applied with the Channel List
menu Press the [MENU] key on the remote control
handset to display the Main Menu and then, using
the [UP] or [DOWN] keys on the remote control,
make sure that the first item, Channel List, is
highlighted in yellow and press the [SELECT] key
Highlight the channel to be locked using the [UP] or
[DOWN] keys You can move through the list 10
channels in one jump using [PAGE UP] or [PAGE
DOWN] Now select the LOCK button at the base
of the screen with the [LEFT] or [RIGHT] keys and
press [SELECT]
A window requesting the PIN code is displayed and
the four-digit code should be entered using the
number keys on the remote control, followed by the
[SELECT] key A lock icon is then displayed
alongside the channel name in the channel list
Hint
The P N is factory set to 0000. This code should
be reset (as described below) to another
sequence of numbers, known only to you, when
you have finished setting up the receiver.
You can now leave the Channel List screen and
return to normal TV viewing by pressing [MENU]
Any attempt to change channel to the locked
channel will now display the same window requesting
the PIN code and the channel will only be displayed
on entry of the correct code To remove the lock on
a channel, repeat the same process as to lock the
channel

MENU LOCK
Simply locking a channel will not deflect a
determined would-be viewer Re-installing the
complete channel list, for example, will bypass the
channel lock However, the menus can be locked
out of use too, to prevent this
Display the Main Menu by pressing the [MENU] key,
highlight Configuration, and press [SELECT] to
display the Configuration menu screen Highlight the
Parental Settings line of the menu (press [DOWN]
five times) and press [SELECT] to display the
Parental Settings menu (after the PIN code has been
entered) Here the menu lock-out can be set and the
PIN code changed
With the Menu Lock line highlighted, use the [LEFT]
or [RIGHT] to cycle the menu lock setting through
Disabled, Main Menu and Installation The Main Menu
setting will lock out the complete menu system; the
Installation Menu setting locks only the Installation
menu (see Section 3 - ADVANCED OPERATION -
Re-installation); and the Disabled setting allows free
access to any of the menus
You must return to normal TV viewing by pressing
the [MENU] key (three times) to activate the lock
Now any attempt to access the locked menus will
display the PIN request window and the menus will
only be displayed on entry of the correct PIN code
The same Parental Settings menu is used to change
the PIN code With the Set Lock Key line
highlighted, press [SELECT] to display the Set Lock
Key window This requests the new four-digit code
to be entered twice (for confirmation) and the new
code comes in effect when you return to the
Configuration menu by pressing [MENU]
-11-

Hint
f you want the channel and menu locks to work
efficiently and actually protect channels from
access, do change the P N code from the factory
default. Make sure that you choose a number
that is not obvious to others but one that can
be remembered by you.
FAVOURITE CHANNELS
There will be some channels that you tend to watch
more often and some only occasionally Although
some duplicate channels you may want to delete
from the channel list, others although not watched
frequently, you will not want to do away with
altogether The favourite mode allows the most-
watched channels to accessed more easily, leaving
the less-watched channels accessible but out of the
way
When the favourite mode is activated, the [P+] and
[P-] keys cycle through the favourite channels only
and the EPG will list the favourite channels only
(other channels can still be accessed by channel list
number or from the Channel List menu screen)
Any channel can be a favourite channel and the
Channel List menu is used to label those channels
you want as favourites
Display the Channel List menu screen by
highlighting Channel List on the Main Menu and
pressing [SELECT]
6(/(&7
L
Use the [LEFT] or [RIGHT] keys to highlight the
FAVOURITE button at the base of the screen and
then, in turn, highlight each channel that is required
to be a favourite channel, using the [UP] and
[DOWN] keys (and the [PAGE UP] or [PAGE
DOWN] keys), and press [SELECT] A channel
selected as a favourite appears in the main channel
list with a favourites icon against the channel name
A channel can have its favourites status
removed by repeating this procedure, to remove the
icon Leave the Channel List menu by pressing
[MENU] Once the required channels have been
marked as favourite channels, the favourite mode
can be activated to allow easy access to them
Press the [MENU] key to display the Main Menu,
the [DOWN] key twice to highlight Configuration,
and press [SELECT] to display the Configuration
screen Press the [DOWN] key four times to
highlight the Favourite Mode line and using the
[LEFT] or [RIGHT] keys change the setting from
Off to On
When you leave the Configuration menu by pressing
[MENU] the favourite mode is activated Now,
changing channel using the [P+] or [P-] keys will
switch to only those channels marked as favourites
in the channel list Similarly, the on-screen list in the
electronic programme guide contains only the
favourite channels
You can still access all the channels in the channel
list by keying in their channel list number or by
selection from the Channel List screen
Alternatively you can switch off the favourite mode
from the Favourite Mode line of the Configuration
menu
Hint
The favourite mode can only be activated if one
or more channels in the channel list are marked
as favourites. Similarly, if the favourite status
is removed from all the channels in the Channel
List, the favourite mode is turned off
automatically.
PROGRAMME REMINDERS AND TIMERS
With the greatly extended channel choice that digital
terrestrial television brings, it is all too easy to miss
a favourite programme The Matsui DTR1 receiver
has two facilities built in to help you make sure you
catch all the TV shows you want
-12-

PROGRAMME REMINDERS
Programme reminders can be set to signal that a
programme is about to start when you are watching
another channel A reminder is set from the
Electronic Programme Guide screen
Press the [GUIDE] key to display the EPG screen
and press [RIGHT] to display the next programme
details in the text window and highlight the name of
the next programme in the list of channels Press
[SELECT] when a programme you want to watch is
highlighted and the reminder icon is displayed
against that programme's name
You can exit the EPG screen in the normal way -
pressing [GUIDE], [MENU] Later, shortly before the
programme is due to start, the receiver will display
a reminder on the screen over the picture of the
channel being viewed
Use the [LEFT] or [RIGHT] keys to highlight the YES
or NO buttons as appropriate and press [SELECT]
If you select the YES button, the receiver switches
over to the reminder channel
Note:Reminder events are ignored if any timer
event is active at that time
EVENT TIMER
You can also set a timer to switch the receiver to
any channel without your intervention Thisis
intended for making video recordings of
programmes when you are out If a single
programme is to be recorded, the receiver can be
left switched to the required channel and the timer
set on the VCR However, if two or more
programmes on different channels are to be
recorded then the Matsui DTR1 receiver's own timer
is set as well, to select the required channel when
it is needed
Display the Main Menu by pressing the [MENU] key
and highlight and select the Timers line to display
the Timer menu screen Up to five separate timer
events can be set and each is displayed in the Timer
screen, showing the event number, the channel to
be selected, the start time, end time, date and the
mode - whether that event is active (and will be acted
on) or not
6(/(&7
L
0(18
To set an event, highlight its mode button using the
[UP] or [DOWN] keys and press [SELECT] to
display the timer entry window Here the five
settings of channel name, start time, end time, date
and frequency mode can be set You can move
freely between each setting using the [UP] and
[DOWN] keys The channel name is set using the
[LEFT] or [RIGHT] keys to display the channel which
broadcasts the programme to be recorded The start
time, end time and date are each set with the
number keys on the remote control in 24-hour
format The frequency mode determines how often
the receiver operates this event and is set with the
[LEFT] or [RIGHT] keys to be either Once, Daily,
or Weekly
Hint
f an invalid number for the start or end times
or the date is entered, the highest valid number
is automatically entered in its place. So,
entering 28:30 as the time will automatically
change to 23:30, and a date of 15:14:2002 will
change to 15:12:2002.
Pressing [MENU] or [SELECT] returns to the Timer
screen with the settings in place in the timer event
list The event mode is automatically set to Active
and you can now return to normal viewing (press the
[MENU] keys) and at the appointed time the
receiver will switch over to the required channel and
at the end of the event, switch the receiver to
standby
-13-

When the Timer screen is displayed, any event can
be set to be Inactive (so it will not occur) or the
channel, times and frequency mode altered by
highlighting the event's Mode button and pressing
[SELECT] as before
You can exit the Timer screen and return to normal
TV viewing by pressing [MENU]
Hint
f you are watching digital terrestrial TV at the
time the timer event starts, a message is flashed
onto the screen announcing that the receiver is
'Switching to timer channel' so you understand
what is happening.
RE-INSTALLATION
Although your DVB-T receiver will not lose its
settings or stored channels when switched off, you
may wish to re-install the receiver because you
have moved to a different area with different
broadcast frequencies, you wish to reinstate a
channel previously deleted from the channel list, or
you want to watch new channels which have started
broadcasting
Press the [MENU] key to display the Main Menu
and using the [UP] or [DOWN] keys, highlight the
Installation line and press [SELECT] to display the
Installation Menu
You can either perform a First Time Installation,
effectively resetting the receiver to its ex-factory
condition, or just search for channels
FIRST TIME INSTALLATION
To reset the receiver, highlight the First Time
Installation line in the menu and press [SELECT] A
warning screen is displayed in case of accidental
operation
Highlight the YES button with the [LEFT] or [RIGHT]
key and press [SELECT] to erase all the channels
and settings and switch the receiver to standby
You can now start again as detailed in Section 1 -
PREPARATION - Tuning In
ADD CHANNELS
The Matsui DTR1 receiver can search for channels
automatically (searching all the broadcast
frequencies for free-to-air channels) or manually
(searching one specified broadcast frequency only
for any channels to be found there)
Press the [MENU] key to display the Main Menu
and using the [UP] or [DOWN] keys, highlight the
Installation line and press [SELECT] to display the
Installation Menu Highlight the Add New Channels
line and press [RIGHT] to display the options Select
Automatic Search with the [UP] or [DOWN] keys
and press [SELECT] A warning message is
displayed This starts the automatic tuning process
as described in Section 1 - PREPARATION - Tuning
In, and searchesthrough all the available broadcast
frequencies for free-to-air channels Previous
channels will be replaced on automatic search
If, alternatively, from the search options menu the
Manual Search line is highlighted and [SELECT]
pressed, the manual search screen is displayed
Highlight the YES button with the [LEFT] or [RIGHT]
key and press [SELECT] to start the automatic
search
This is for searching for digital channels on a single
broadcast frequency The frequency channel
number (21-69) is entered in the box at the top left
of the screen and the received signal level and signal
quality can be observed on the two bar graphs at the
bottom When [SELECT] is pressed, the receiver
searches that frequency and display a list of the
channels found Before returning to the Installation
menu
-14-

Hint
The bar graphs of signal quality and signal level give a good indication of whether any channels
are likely to be found. f only the signal level graph shows a high value then it is likely that an
analogue channel occupies that broadcast frequency. f the signal quality bar is high as well then
it is a digital frequency and digital channels will probably be found.
Again, channels which duplicate those already in the channel list are ignored However, the manual channel
search will find all channels on the broadcast frequency
When either search is finished, press the [MENU] key to return to normal broadcast viewing, to watch the
new digital terrestrial television channels found
OVER AIR DOWNLOAD
Over Air Download: To ensure that your digital receiver always has the most up todate information Please
ensure that after use it is set to its standby mode The DTR 1 automatically powers up at 3AM each day
and searches for any new information which may be broadcast and will download this to your box
automatically This operation will normally take approximately 30 seconds
If you have an important recording to make at 3AM which must not have a 30 second interrupt then you
can disable the auto OAD search by performing the following:
1 Press Menu button and using the up / down buttons highlight CONFIG and press the SELECT button,
2 Use the up and down buttons to highlight "RECEIVER UPGRADE" and press SELECT button
3 Using the left / right button change function from Enable to Disable
4 Press SELECT button then MENU and MENU to return to Normal l operation
Do not forget to re enable the automatic OAD function after you have made your recording by repeating
the above instructions but this time selecting ENABLE
-15-

CONNECTING A VCR OR DVD (WITH ONE SCART SOCKET)
If the VCR has only one SCART socket, you can connect the equipment as follows:
$17,1 79287 56
6&$57

79

6&$5 7

9&5$8;

5(6(7
$&  9
+]
PD[ :
a
/
5
$8',2
5
/
79$HULDO
+L)L
9&5
6FDUW
7
9
79
$HULDO $HULDO
,Q
$HULDO
2XW
Both live and recorded digital terrestrial television programmes are watched at a lesser quality via the TV
aerial input only To view via SCART, press the AV button on your TV remote control
-16-
VCR or DVD

CONNECTING A VCR AND DVD (WITH TWO SCART SOCKETS)
If your TV and VCR both have two scart sockets you can connect as follows Unplug the aerial lead and
connect this to the ANT IN socket on the rear of your receiver Connect the aerial lead (supplied) from the
TV OUT on the receiver to the ANT IN on the rear of the VCR Then connect an aerial lead from the TV OUT
on the VCR to the ANT IN socket on the rear of your TV
Connect a scart lead from the TV SCART socket on the rear of the receiver to the SCART 1 socket on the
rear of the TV
Connect a scart lead from the VCR SCART to the SCART 1 on the VCR, and connect a scart lead from
the SCART 2 on the VCR to the SCART 2 on the rear of the TV
$17,1 79287 56
6&$5779 6&$579&5$8;
5(6(7
$&9
+]
PD[:
a
/
5
$8',2
5
/
79$HULDO
+L)L
'9'
6FDUW
6FDUW
79
79
$HULDO
$HULDO,Q
9&5
You can now record digital terrestrial television programmes by selecting SCART 1 on the VCR The VCR
will also be able to record analogue television channels in the usual way Both live and recorded digital terrestrial
television programmes can be viewed on the TV by selecting the TV's AV input
-17-