Maximum 057-2330-8 User manual

TABLE OF CONTENTS
TABLE OF CONTENTS
NOTE: If any parts are missing or damaged, or if you have any
questions, please call our toll-free helpline at 1-888-670-6682.
Parts list
Assembly 5
Specifications
Safety guidelines 10
Operation
Warranty
3
SAVE THESE INSTRUCTIONS.
This manual contains important safety and operating
instructions. Read all instructions and follow them with
use of this product.
TM
CONSERVEZ CES INSTRUCTIONS.
11
15
4
9

PARTS LIST
4
F. Workpiece Supports x2
D. Wheels x2
C. Wheel Axle x1
E. Handle x1
NOTE: If any parts are missing or damaged, or if you have any
questions, please call our toll-free helpline at 1-888-670-6682.
G. Locking Knobs x2
Model No.057-2330-8 | Contact us: 1-888-670-6682
B. Bracket x1
J. Mounting Brackets ×2
H. Blocker x2 I. Spring x2
Hex Bolt M6x35 x4
K
Flat Washer x8
Nut x8
M1 M6 x4
M2 M8 x2
M3 M12 x2
M
O
Bolt M6x15 x4
L
L1. M6 x6
L2. M8 x2
NBolt M6x35 x2
A.Table x1

WARNING
Ensure that the saw stand is stable and that all locking
pins have been engaged.
Assembling the Saw Stand
Carefully remove all parts included in the
delivery from their packaging.
ASSEMBLY
5
TM
Put the wheel axle C through the hole of the ( )
4
3
5
2
2
4
5
3
bracket (B) (step ) Secure in place using flat.
washer (M3) (step ), wheel (D) (step ),
1
2 3
1
Installing the Wheels (see Figs. 1 and 2)
Fasten the bracket (B) to the table (A) with
bolt (K) and nut (L1) .
2
washer (M2) (step ), and nut (L2) (step )
4 5
Repeat with the other wheel.
1
.

Model No.057-2330-8 | Contact us: 1-888-670-6682
6
4
5
Setting up the Saw Stand (see Figs. 4 and 5)
Lay the saw stand upside down on the
floor (legs facing upward).
Push the locking pin in and tilt the leg
upward until the lock pin can be heard to
engage Repeat with the other three legs. .
Flip the saw stand back to the working
position.
firmlyagainst the floor (step
Tighten the lock nut again (step
The saw stand is easily levelled with
its height-adjustable legs.
Loosen lock nut (step
the leg in or out until the saw stand
is aligned level and all four legs are
) and screw
).
).
1
2
3
3Installing the Handle (see Fig. 3)
Insert the handle (E) onto the two tubular
brackets on the end of the table (A) and
secure in place with bolt (N) and nut (L1).
31 2
ASSEMBLY

7
TM
7
)
6
Loosen the locking knobs (step
Pull the table extensions out to the
desired length (step ) and secure
the table extensions by tightening
the locking knobs.
Insert the workpiece supports (F)
into the table extensions (step ).
Adjust the height of the workpiece
supports (F).
Tighten the locking knobs (G) with
spring (I) and blocker (H) to lock
1
2
3
4
Extending the Saw Stand
(see Figs. 6and7)
22
1
3
4
the workpiece support (F) (step ).
WARNING
Ensure that the saw stand is stable and that all locking
pins have been engaged.
ASSEMBLY

Model No.057-2330-8 | Contact us: 1-888-670-6682
8
6
8
7
Fastening the Mounting Brackets
onto the Saw Stand (see Figs. 6 and 7)
Push the locking pin (step ) and
open the locking handle (step ).
Align both mounting brackets (J)
parallel to each other. Position the
mounting brackets (J) on the saw
stand and push the locking handle
down until the locking pin can be
heard to engage.
Adjusting the Mounting Brackets
(see Fig. 8)
After intensive use of the saw stand,
the mounting brackets may require
readjustment. Turn the mounting
brackets (J) upside down and screw
the adjustment screw in clockwise/
counter-clockwise direction
according to your needs.
1
2
1
2
ASSEMBLY

9
TM
500 lb (226.8 kg)
Length of saw stand without table extensions 45 1/4'' (1.15 m)
Length of saw stand with table extensions 8' 2" (2.5 m)
Maximum height 32 5/16" (82 cm) from ground to tabletop
Max
500 lb
The maximum load (power tool and workpiece) of the saw
stand is 500 lb (226.8 kg). Do not overload the saw stand
and do not use it as a ladder or scaffolding.
(226.8 kg)
Weight 43 lb (19.5 kg)
SPECIFICATIONS
SPECIFICATIONS
Maximum load
WARNING
45 1/4'' (1.15 m)
32 5/16"
(82 cm)
8' 2" (2.5 m)

Model No.057-2330-8 | Contact us: 1-888-670-6682
10
SAFETY GUIDELINES
General Safety Rules
Read all warning notes and instructions enclosed with the saw stand and the
power tool to be mounted. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Safety Warnings for Saw Stands
Pull the plug from the mains receptacle and/or remove the battery from the
power tool before making adjustments on the tool or changing tool
accessories.
Unintentional switching on of the power tool is the cause of many accidents.
Assemble the saw stand in the proper manner before mounting the power tool.
Proper assembly is important to prevent the risk of a collapse of the saw stand.
Attach the power tool securely to the saw stand before using it. Slipping of the
power tool on the saw stand can lead to loss of control.
Place the saw stand on a firm, level and horizontal surface. If the saw stand can
slip off or wobbles, the power tool or the workpiece cannot be uniformly and
securely guided.
Do not overload the saw stand and do not use it as a ladder or scaffolding.
Overloading or standing on the saw stand can lead to the upward shifting of the
centre of gravity of the stand and its tipping over.
When working or transporting, take care that all bolts and connecting elements
are firmly tightened. The mounting brackets sets for the power tool must
always be firmly locked. Loose connections can lead to instability and inexact
sawing.
When the power tool is mounted to the mounting brackets, operate it
exclusively on the saw stand. Without the saw stand, the power tool with the
mounting brackets on does not stand securely and can tip over.
Ensure that long and heavy workpieces do not affect the equilibrium of the saw
stand. Long and/or heavy workpieces must be supported at the free end.
Keep your fingers clear of the hinge points while putting the saw stand
together or pulling it apart. Otherwise, your fingers may get crushed or
contused.
WARNING
This manual contains important safety and operating
instructions. Read all instructions and follow them with
use of this product.

11
TM
OPERATION
WARNING
9
10
· Do not overload the saw stand. Always observe the
maximum load of the saw stand and the two table
extensions.
· Always hold the workpiece firmly, especially the
longer and heavier section.
Fastening the Mitre Saw to the
Mounting Brackets (see Fig. 9)
Unplug the saw and lock the saw arm
in the down position.
Lower the saw down onto the
brackets (J), feeding the hex bolts (O)
through the sliding plate.
Secure in place using a flat washer
(M1).
Repeat steps to install second
bracket (J) to the other side of the
saw.
After making sure both brackets (J) are
parallel to each other, finger tighten
all four hex bolts (O) to hold in
position.
Attaching the Mounting Brackets (see
Fig. 10)
Place both mounting brackets (J) on
the saw stand. Hand tighten both
locking handles.

OPERATION
12
Model No.057-2330-8 | Contact us: 1-888-670-6682
11
12
WARNING
·Always hold the workpiece firmly, especially the
longer and heavier section.
Sawing
Workpieces of the
Same Length
The material stop
can be used for
easily sawing
workpieces to the
same length.
Tilt the material
stop upward.
Position the
workpiece support
(F) at the desired
clearance to the
saw table of the
power tool.
(see Figs. 11 and 12)

13
OPERATION
TM
13
14
15
Folding the Saw Stand with Power
Tool (see Figs. 13 and 15)
Lock the saw arm in the down
position (step ) Push the table .
extensions into the table (steps
and ).
First lock the locking knobs on the table
Release the locking handles and
move the power tool to the wheel
side of the saw stand.
Firmly tighten both locking
handles of the mounting brackets (J).
First hold the miter saw stand on the
wheelside, fold the legs into the table
(step ), then fold the other two legs
).
Then you can easily move the
power tool together with the saw
stand.
1
2
3
4
5
6
in the down position and then tighten
thelocking knobs (G) to lock the
workpiece supports (F) and table
5
6
3
4
2
1
extensions(step ).
(step

Model No.057-2330-8 | Contact us: 1-888-670-6682
14
OPERATION
16
CAUTION!
WARNING
· Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a second
is enough to cause severe injuries.
· Before attempting to use this mitre saw stand,
become familiar with all of its operating features and
safety requirements.
· To reduce the risk of serious personal injury, turn tool
off before making any adjustments or removing/
installing attachments or accessories.
· The maximum load (power tool) of thesaw stand is
110 lb (50 kg) when moving . Do not overload the saw
stand .
Max
1 l10 b
(50 kg )
· Do not stand vertically with tool attached .

15
TM
WARRANTY
This MAXIMUM product is guaranteed for a period of 5
years from the date of original retail purchase against
defects in workmanship and materials only and is
subject to the following components:
Component A: The carrying case is guaranteed for a
period of 1-year from the date of original retail
purchase against defects in workmanship and materials.
a)
Component B: Accessories, including drill bits and
saw blades, do not carry a warranty.
b)
Subject to the conditions and limitations described
below, this product, if returned to us with proof of
purchase within the stated warranty period and if covered under this warranty, will be
repaired or replaced (with the same model, or one of equal value or specification), at
the sole discretion of the Maximum Canada authorised repair centre ( “Service
Provider” ). We will bear the cost of any repair or replacement and any costs of labour
relating thereto.
5-Year Limited Warranty
These warranties are subject to the following conditions and limitations:*
a bill of sale verifying the purchase and purchase date must be provided;
a)
defects in workmanship and material to be assessed and determined by the Service
Provider;
b)
this warranty will not apply to any product or part thereof which is worn or broken or
which has become inoperative due to abuse, misuse, accidental damage, neglect or
lack of proper installation, operation or maintenance (as outlined in the applicable
owner's manual or operating instructions);
c)
this warranty does not apply to normal wear and tear or to expendable parts or
accessories (including drill bits and saw blades) that may be supplied with the
product that by their nature have a limited life span and are expected to become
inoperative or unusable after a reasonable period of use;
d)
this warranty will not apply to routine maintenance and consumable items such as,
but not limited to, fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids,
rubber o-rings, tune-ups or adjustments;
e)
this warranty excludes the following components that may accompany your product:
f)
The carrying case, which is only for a period of 1-year from the date of original
retail purchase against defects in workmanship and materials.
(1)
Accessories, including drill bits and saw blades, which do not carry a warranty of
any kind.
(2)
g) this warranty will not apply where damage is caused by repairs made or attempted
original retail

by others (i.e. persons not authorized by the manufacturer), and any such
unauthorized repairs or attempted repairs shall void this warranty in its entirety;
this warranty will not apply to any parts other than original parts, except to the
extent that the retailer or manufacturer or persons authorized by either of them have
repaired or replaced them;
h)
this warranty will not apply to any product that was sold to the original purchaser as
a reconditioned or refurbished product (unless otherwise specified in writing);
I)
this warranty will not apply to any product or part thereof if any part from another
manufacturer is installed therein or any repairs or alterations have been made or
attempted by unauthorized persons;
j)
this warranty will not apply to normal deterioration of the exterior finish, such as, but
not limited to, scratches, dents, paint chips, or to any corrosion or discolouring by
heat, abrasive and chemical cleaners;
k)
this warranty will not apply to component parts sold by and identified as the product
of another company, which shall be covered under that product manufacturer's
warranty, if any;
l)
any products replaced by the retailer in attempt to fulfill warranty obligations is
subject to the original product warranty conditions and related time period as
initiated by the original date of purchase; if product is purchased in Quebec, the
warranty term will be extended for a period equal to the time during which the
Quebec retailer possesses the product in attempt to fulfill warranty obligations;
replaced product will not default to new product warranty conditions; and
m)
The retailer and manufacturer's sole obligation and the purchaser's sole remedy
under this warranty shall be as set out herein. The warranties contained herein are
not transferable and are given only to the purchaser.
WARRANTIES OR CONDITIONS, WHETHER EXPRESS, IMPLIED OR STATUTORY
(INCLUDING SUCH AS ARISE UNDER THE SALE OF GOODS ACT OR THE
INTERNATIONAL SALE OF GOODS ACT), ARISING OUT OF A COURSE OF DEALING
OR USAGE OF TRADE OR OTHERWISE, INCLUDING, SUBJECT TO APPLICABLE LAW,
ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY,MERCHANTABLE
QUALITY, FITNESS OR ADEQUACY FOR A PARTICULAR PURPOSE OR USE, AND ALL
n)
Model No.057-2330-8 | Contact us: 1-888-670-6682
16
·To reduce the risk of serious personal injury, turn tool
stand and do not use it as a ladder or scaffolding.
WARRANTY
FURTHER, THE WARRANTIES SET OUT HEREIN ARE IN LIEU OF ALL OTHER
OTHER SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED BY THE
RETAILER AND MANUFACTURER.
Additional Limitations
This warranty applies only to the original purchaser and may not be transferred.

17
TM
WARRANTY
This warranty applies for a period of 5 years from the date of original retail purchase,
as indicated on the bill of sale.
Neither the retailer, Maximum Canada, nor the manufacturer shall be liable for any other
expense, loss or damage, including, without limitation, any indirect, incidental,
consequential or exemplary damages arising in connection with the sale, use or inability
to use this product.
Under no circumstances shall the retailer, Maximum Canada, or manufacturer be liable
to the purchaser for any claim for (a) indirect, special, punitive, incidental, exemplary, or
consequential damages, (b) compensation for loss of profits, anticipated revenue,
savings or goodwill, or other economic loss of the purchaser, (c) exemplary, aggravated
or punitive damages howsoever incurred, (d) contribution or set-off in respect of any
claims against the purchaser, (e) any damages whatsoever relating to third party
products or services or the purchaser's materials, or (f) any damages whatsoever
relating to interruption, delays, errors or omissions; in each case under any theory of
law or equity, arising out of or in any way related to this warranty, even if advised of the
possibility thereof. Notwithstanding any provision herein or entitlement of the
purchaser at law, in equity or otherwise, in no event shall the liability of the retailer or
manufacturer under this warranty, whether in contract, tort, product liability or
otherwise, exceed, in the aggregate, the amount paid by the purchaser to the retailer
for the product to which this warranty applies.
*Notice to Consumer
This warranty gives you specific legal rights, and you may have other rights, which may
vary from province to province. The provisions contained in this warranty are not
intended to limit, modify, take away from, disclaim or exclude any statutory warranties
set forth in any applicable provincial or federal legislation.
In addition to the 5-Year Limited Warranty, this MAXIMUM product is covered by our:
1-Year Repair Warranty
Maximum Canada will maintain this product and replace critical parts which have worn
beyond reasonable use through normal use of such product, any time during the first
year after purchase.
The following are excluded from this 1-Year Repair Warranty:
a) Missing or damaged parts or components that are a result of abuse or misuse;
b) Any wear and tear to non-critical parts or accessories that do not affect the core
function of the product.
90-Day Satisfaction Guarantee
If you are not completely satisfied with the performance of your MAXIMUM product for
any reason, you can return it within 90 days from the date of purchase with proof of
purchase for exchange or a full refund.

Made in China
Imported by
MAXIMUM Canada Toronto, Canada M4S 2B8
Model No.057-2330-8 | Contact us: 1-888-670-6682
18
WARRANTY