MCM HOUSE LUNA User manual

Assembly instructions
- We suggest you spend a short time reading through this leaet and then follow the simple step by step instructions.
- Do not discard any of the packaging until you have checked that you have all the parts and the pack of ttings.
MCM HOUSE
PARTS
LUNA DINING TABLE | MCM HOUSE T. 1300 997 975 | MCMHOUSE.COM PAGE 1 OF 5
LUNA DINING TABLE
A
Top
1x
B
2x
C
1x
D
1x
E
M6x25mm
12x
F
M5x40mm
16x
G
1x
H
1x
Pre Drill Bit
1
1. Assemble the base rst.
2. Attach part C to Part D with Screws E.
3. Tighten with Allen Key G - ensure it is as tight as possible.
4. Attach Parts B to Base C with remaining Screws E - ensure tight.
C
D
E
G
E
C
B
B
E
G
E
I
2x
Felt Feet
Tape MeasurePhillips Head Bit
REQUIRED
Brushless Hammer Drill
19 21 23
25
Impact Driver
1 2 34
D
2 people
required or
assembly

PAGE 2 OF 5
LUNA DINING TABLE | MCM HOUSE T. 1300 997 975 | MCMHOUSE.COM
2
3
- To protect your oor and your new Dining Table, lay a drop sheet or something that is a clean so surface.
- Lay your new table top face down on the Drop sheet so that the black metal brackets are showing face up.
D
I
I
- The base needs to be completely assembled and secure before Felt pads 'I' are to be attached. If the base is not correctly
assembled before applying Felt Pads 'I' - it will mean you need to remove the felt pads, this is dicult and reduces adhesive
when reapplied.
- Ensure felt pads are being stuck to the underside of part D.
A

PAGE 3 OF 5
LUNA DINING TABLE | MCM HOUSE T. 1300 997 975 | MCMHOUSE.COM
5
- Upon your face down table top, center your base upside down ensuring the felt feet are facing up.
- Knowing what size table top and base you have purchased - refer to the chart below as a guide to ensure your table base is centered.
4
- On your Pre Drill Bit (H), use a tape measure(4) to determine 30mm from the end of the drill bit.
345 6 78 9
1 2
5m
16FEET 3
TAPE MEASURE(4)
(NOT PROVIDED)
PRE DRILL BIT (H)
A
B
B
BOTTOM VIEW
A
BB
C
D
TAPE MEASURE(4)
(NOT PROVIDED)
1100 Base
1800 top needs 350 on each end
2000 top needs 450 on each end
1600 Base
2200 top needs 300 on each end
2400 top needs 400 on each end
2100 Base
2800 top needs 350 on each end
3000 top needs 450 on each end

PAGE 4 OF 5
LUNA DINING TABLE | MCM HOUSE T. 1300 997 975 | MCMHOUSE.COM
7
6
A
B
B
- Once the table base is centered, use the Brushless Hammer Drill (2) with Pre Drill (H) bit to predrill holes where the
screws will secure the top to the base.
- Ensure you predrill slowly with even pressure, directly from above and not at an angle to a depth of 30mm which you
have already marked on your pre drill bit (H).
- Switching to impact driver (1) with Phillips Head Bit (3) and using screws F, screw down applying even pressure until the screw is 1/3
submerged into the table top.
- Switch your drill to reverse, reverse the screw out, switch back and drill down again until the screw is 2/3 submerged, then reverse out.
- Changing back to drill, apply even pressure screwing the screw down until it's fully submerged and the head of the screw sits ush
with the metal base.
A
B
B
PHILLIPS HEAD BIT (3)
(NOT PROVIDED)
IMPACT DIVER (1)
(NOT PROVIDED)
F
F
PRE DRILL BIT (H)
BRUSHLESS HAMMER DRILL(2)
(NOT PROVIDED)
19
21 23
25

PAGE 5 OF 5
LUNA DINING TABLE | MCM HOUSE T. 1300 997 975 | MCMHOUSE.COM
6
- Carefully turn the table to be on the right side up, and place it in your desired location.
WARNING:
-These table parts can be cumbersome and heavy; the assistance of two or more people is recommended in order to prevent personal injury
and ensure the table parts are not damaged during the assembly process.
- Keep fittings out of childrens' reach