MD SPORTS 39600 User manual

MODEL/MODELO: 39600
Please contact us before returning the product to the store.
Toll Free: 877-852-8164
Por favor póngase en contacto con nosotros antes de
devolver el producto a la tienda.
Número telefónico gratis: 877-852-8164
INSTRUCCIONES DE ARMADO

LIMITED 90 DAYS WARRANTY
1
This product is covered by a limited warranty that is effective for 90 days
from the date of purchase. The warranty covers any defects in parts and
workmanship.
This Limited Warranty gives you specific legal rights and you may also have
other rights which very from one state (province) to another.
If, during the limited warranty period, a part is found to be defective or
breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, tabletops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper
usage, alteration, misuse, abuse, accidental damage or neglect.
Attention: Since you build all tables upside down, please inspect table tops
and playing surfaces right away before putting together.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required
before any warranty service is initiated. All requests for warranty service can
be submitted by email, in writing or by contacting our Consumer service
Department at:
TOLL FREE: 877-852-8164
WEBSITE: www.medalsports.com.tw
*Please do not call our 800 NUMBER as well as email us. This will result in
duplicate orders and charges will occur.
*Please note that all damaged table tops need to be returned to the store.
We do not replace any tabletops or playing surfaces.
PLEASE CONTACT US BEFORE RETURNING THE
PRODUCT TO THE STORE. THANK YOU VERY MUCH!

Phillips Screwdriver – Not Included
Standard (Flat Head Screwdriver) – Not Included
Allen Wrench - Included
TOOLS REQUIRED:
ASSEMBLY TIPS:
:

!



!
2
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least two adults are required.
Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 -
2 -
Please Keep Your Instructions! Your Model number is necessary should you need to contact
us. Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts identifier below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on:
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
877-852-8164
Power Tools
- Set Low Torgue
High Torque
over tightened
High Torque
over tightened
CAUTION !
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.

3
39600 PARTS LIST
Main Cabinet
1 Piece
Leg
4 Pieces
Billiard Ball
1 set
Lower End Apron
2 Pieces
Lower Side Apron
2 Pieces
Apron Corner
4 Pieces
8 x 60mm Bolt - Black
12 Pieces
22 x 8.5mm Washer
24 Pieces
8 x 18mm Bolt - Silver
12 Pieces
6 x 23mm Bolt - Black
8 Pieces
6 x 35mm Bolt - Silver
16 Pieces
18 x 6.5mm Washer
8 Pieces
Brush
1 Piece
Top Cue Rack
1 Piece
3.5 x 40mm
Flat Head Screw
8 Pieces
Chalk
2 Pieces
3.5 x 14mm
Washer Head Screw
48 Pieces
Pre-installedPre-installed
“L” Steel Bracket
12 Pieces
Leg Base-A
4 Pieces
Cue
2 Pieces
Triangle
1 Piece
Allen Key
1 Piece
Bottom Cue Rack
1 Piece
Side Cue Rack
2 Pieces
Cue Rack Base
2 Pieces
Table Tennis Surface - A
2 Pieces
Table Tennis Surface - B
1 Piece
4 x 25mm
Washer Head Screw
10 Pieces
Table Tennis Support
(with Velcro Strap)
2 Pieces
Table Tennis Post
2 Pieces
Table Tennis Paddle
2 Pieces
Table Tennis Ball
2 Pieces
Table Tennis Net
1 Piece
12345
6 7 8 9 10
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
31 32 33
Shim
8 Pieces
34
Plastic Barrel Nut
8 Pieces
36 37
Plastic Nut
8 Pieces
38
Cross Barrel Nut
16 Pieces
39 40
Iron Nut - B
10 Pieces
EVA Pad
12 Pieces
35
Pre-installed Pre-installed Pre-installed Pre-installed
Leg Base-B
4 Pieces

4
FIG.1
ASSEMBLY INSTRUCTIONS
3. Attach the Lower Side Aprons (#5) and Lower End Aprons (#4) to the Main Cabinet (#1) using eight Screws (#13).
See FIG.1.
FIG. 1
4
5
1
13
13
5
436
1. Find a clean, level place to begin the assembly of your Billiard Table. The table will be assembled upside down
and then turned over on its legs once the assembly completed. This game table is heavy, and turning it over will
require at least four strong adults.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts list.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.
41 Pre-installed
8 x 55mm Bolt
12 Pieces

5
FIG.2
4. Attach the “L” Steel Bracket (#15) to the apron using one Bolt - Silver (#9) and one Washer (#8) per “L” Steel
Bracket. See FIG.2
FIG. 2
9
8
15 8
9
9
8
SILVER BOLT
SILVER BOLT
SILVER BOLT
14

5. Attach the Apron Corner (#6) to the arpons using two Bolts (#10) and two Washers (#11) per Apron Corner.
See FIG.3.
6
FIG.3
6. Attach the Leg Base-A (#16) to the aprons using four
Bolts - Silver (#12) per Leg Base. See FIG.4.
FIG.4
FIG. 4
16
12
12
16 38
SILVER BOLT
SILVER BOLT
FIG. 3
6
10 11
37

8. Lift the table assembly from the floor with four strong adults, turn it over, and set table on its legs in the location
where you play. Go back and make sure that all connections are tight.
7
FIG.5
7. Attach the Leg (#2) to the Leg Base - A & B (#16 & #40) using three Bolts (#7) and three Washers (#8) per Leg.
See FIG.5.
HOLD TABLE CABINET DO NOT
HOLD THE
LEGS
DO NOT LEANTHE
TABLE ON ITS LEGS!
CAUTION: Four strong adults are recommended to turn the table over as shown.
1. Lift the table off the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.
FIG. 5
8
7
2
40

8
34
34
34
Note: Utilize shims (#34) if needed (as shown) to level the table.
FIG.6
27
FIG. 6
28
27
35
35
FIG.6A
NOTE: DO NOT lift the table by the pockets. If you move the table, do not lift it by placing your hands
beneath the pockets and do not lean or put pressure on them. Do not lean or sit on the end or side
rails as this may damage the table.
9. Tear off the backside paper of the EVA Pad (#35) and stick them at the bottom of the Table Tennis Surface - A and
B (#27 and #28). See FIG.6A.

FIG.7
9
FIG. 7
10.Assemble the Table Tennis Surface -A(#27) and Table Tennis Surface - B (#28) together. Place the Table Tennis
Surface (#27 & #28) onto the billiard surface using the Table Tennis Supports (#29) and insert the Net Posts (#30)
and Net (#33). See FIG.7.
33
30
29
27
27
28

11. Attach the Side Cue Racks (#24) to the Top Cue Rack (#22) and Bottom Cue Rack (#23) using six Screws
(#26) See FIG.8.
12. Attach the Cue Rack Bases (#25) to the Side Cue Racks (#24) using four Screws (#26) See FIG.8.
FIG.8
10
FIG.8
26 22
26
24
24
26
26
23
25
26
26
25
39

11

12

13
39600 LISTA DE PARTES
Gabinete Principal
1 Pieza
Pierna
4 Piezas
Pelota de Billar
1 Juego
Delantal Final Inferior
2 Piezas
Delantal Lateral Inferior
2 Piezas
Delantal de Rincón
4 Piezas
Tornillo –Negro
8 x 60mm
12 Piezas
Arandela
22 x 8.5mm
24 Piezas
Tornillo – Plata
8x18mm
12 Piezas
Tornillo –Negro
6 x 23mm
8 Piezas
Tornillo – Plata
6x35mm
16 Piezas
Arandela
18 x 6.5mm
8 Piezas
Cepillo
1 Pieza
Estante de Taco Superior
1 Pieza
Tornillo de Cabeza Plana
3.5 x 40mm
8 Piezas
Tiza
2 Piezas
3.5 x 14mm Tornillo
de Cabeza de Arandela
48 Piezas
Pre-instaladoPre-instalado
Anaquel “L”de Acero
12 Piezas
Base de Pierna - A
4 Piezas
Taco
2 Piezas
Triángulo
1 Pieza
Llave Allen
1 Pieza
Estante de Taco Inferior
1 Pieza
Estante de Taco Lateral
2 Piezas
Base de Estante de Taco
2 Piezas
Superficie de Mesa de
Tenis – A
2 Piezas
Superficie de Mesa de
Tenis – B
1 Pieza
4 x 25mm Tornillo
de Cabeza de Arandela
10 Piezas
Soporte de Mesa de Tenis
(Correa con velcro)
2 Piezas
Poste de Mesa de Tenis
2 Piezas
Paleta de Mesa de Tenis
2 Piezas
Pelota de Mesa de Tenis
2 Piezas
Red de Mesa de Tenis
1 Pieza
12345
6 7 8 9 10
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
31 32 33
Calzo
8 Piezas
34
Tuerca de Barril Plástica
8 Piezas
36 37
Tuerca Plástica
8 Piezas
38
Tuerca de Barril Cruzada
16 Piezas
39 40
Tuerca de Hierro – B
10 Piezas
Almohadilla EVA
12 Piezas
35
Pre-instalado Pre-instalado Pre-instalado Pre-instalado
Base de Pierna - B
4 Piezas

14
FIG.1
INSTRUCCION DE MONTAJE
1. Encuentre un lugar limpio y nivelado para empezar a montar su Mesa de Billar. La mesa será montada con la parte
superior guiado hacia abajo y una vez que el montaje es compl- etado, se le voltea encima de sus patas. Esta
mesa de juego es pesada y para voltearlo será requerido por lo menos dos adultos.
2. Retire todas las partes desde la caja y verifique que Ud. tiene todas las piezas como se muestra en el dentificador
de las partes como se le indica.Cuidadosamente corte y arranque las cuatros esquinas de la caja de manera
que la parte inferior de la caja pueda ser usada como su superficie para el trabajo.
3. Adjunte el Delantal Lateral Inferior (#5) y el Delantal Final Inferior (#4) al Gabinete Principal (#1) usando ocho
Tornillos (#13)
FIG. 1
4
5
1
13
13
5
436
41 Pre-instalado
Tornillo
8 x 55mm
12 Piezas

15
FIG.2
FIG. 2
9
8
15 8
9
9
8
Plata
4.Adjunte elAnaquel “L”deAcero (#15) al delantal usando un Tornillo-Plata (#9) y unaArandela (8) porAnaquel “L”de
Acero. Vea la FIG. 2
Plata
Tornillo – Plata
14

16
FIG.3
FIG.4
5. Adjunte el Delantal de Rincón (#6) al delantal usando dos Tornillos (#10) y dos Arandelas (#11) por Delantal de
Rincón. Vea la FIG. 3
6. Adjunte la Base de Pierna (#16) al delantal usando cuatro
Tornillos – Plata (#12) por la Base de Pierna. Vea la FIG. 4
Tornillo – Plata
Tornillo – Plata
FIG. 4
16
12
12
16 38
FIG. 3
6
10 11
37

17
FIG.5
FIG. 5
7. Adjunte la Pierna (#2) a la Base de Pierna - A & B (#16 & #40) usando tres Tornillos (#7) y tres Arandelas (#8)
por Pierna. Vea la FIG. 5
8. Levante la mesa montada del piso con cuatro adultos fuertes, voltee la mesa y ponga la mesa sobre sus piernas
en la posición donde usted juega. Vuelva y asegúrese que todas las conexiones están apretadas.
COJA LA MESA
MARCO
PRINCIPAL NO COJA
LA MESA
POR LAS
PATAS
NO INCLINE
LA MESA SOBRE
SUS PATAS
Advertencia:
Se recomienda que cuatro adultos fuertes le den la vuelta a la mesa como se muestra.
1. Levante la mesa del suelo.
2. Dele la vuelta a la mesa.
3. Póngala sobre las cuatro pastas al mismo tiempo.
8
7
2
40

18
NOTA:Utilice el Calzo (#34) si fuera necesario (como demostrado) para nivelar la mesa.
FIG.6
27
FIG. 6
28
27
35
35
FIG.6A
NOTA: QUE NO levante la mesa por los bolsillos. Si usted mueva la mesa, no levantes por colocando sus
manos bajo los bolsillos y no inclínese o haga presión sobre ellos. No inclínese o siéntese sobre
el lado de barra por que se podría dañar la mesa.
9. Arranque la trasera del papel de la Almohadilla Eva(#35) y péguelos en el fondo de la Superficie de Mesa de
Tenis - A y B (#27 y #28). Vea la FIG. 6A
34
34
34

FIG.7
19
FIG. 7
10.Coloque la Superficie de Mesa de Tenis (#27 & #28) sobre la superficie de billar usando el Soporte de Mesa de
Tenis (#29) e inserte los Postes de Red (#30) y la Red (#33). Vea la FIG. 7.
33
30
29
27
27
28