Meden-Inmed GALAXY User manual

INSTALLATION AND OPERATION MANUAL
GALAXY
Massage T
a bl e
Manufacturer:
MEDEN - INMED Spółka z o.o.
UL. WENEDÓW 2
75-847 KOSZALIN
POLAND
TEL. + 48 94 3471040
FAX. + 48 94 3471041
Distribution and servicing in Poland:
MEDEN - INMED Spółka z o.o.
UL. WENEDÓW 2
75-847 KOSZALIN
POLAND
TEL. + 48 94 3471040
FAX. + 48 94 3471041

Page 2 of 15
2014-05-19 GALAXY table - Manual En
CONTENTS
1. INTRODUCTION 3
2. FEATURES OF GALAXY MASSAGE TABLES 4
2.1. USAGE 4
2.2. TECHNICAL DATA 4
2.3. GALAXY 2 SECTION HEADREST (MERCURY S2.FX, S2.FX-H) 5
2.4. GALAXY 2 SECTION HEADREST, ADJUSTABLE ARMRESTS (MERCURY S4.FX, S4.FX-H) 5
2.5. GALAXY 2 SECTION BACKREST (MERCURY E-S2.FX, E-S2.FX-H) 5
2.6. GALAXY 3 SECTION (JUPITER S3.FX, S3.FX-H) 6
2.7. GALAXY 3 SECTION, ADJUSTABLE ARMRESTS (JUPITER S5.FX, S5.FX-H) 6
3. DESIGN AND FUNCTIONS 7
3.1. TABLE COMPONENTS 7
3.2. ADDITIONAL ACCESSORIES 8
3.3. TABLE SET 8
3.4. TRANSPORT AND STORAGE 8
4. SAFETY MEANS 9
5. PREPARING THE UNIT FOR USE 9
6. OPERATING THE TABLE 10
6.1. LEVELLING THE TABLE 10
6.2. HEIGHT ADJUSTMENT –RAISING (LOWERING) OF THE BED 10
6.3. ADJUSTMENT OF THE ADJUSTABLE SECTION INCLINATION/DECLINATION 11
6.4. MOVING THE TABLE 11
6.7. ACCESS CONTROL (ELECTRIC MODELS ONLY) 12
7. MAINTENANCE 13
7.1. CLEANING THE UPHOLSTERY 13
7.2. MAINTENANCE OF THE BASE AND MECHANICAL PARTS 13
7.3. CHECKING THE GAS SPRINGS 14
7.4. PERIODIC CHECK OF ELECTRICAL SAFETY 14
8. WARRANTY CARD 15

2014-05-19 GALAXY table - Manual En
Page 3 of 15
1. INTRODUCTION
Congratulations on a perfect choice of our massage table. GALAXYtables are stable, reliable and easyto use. These
features result from careful design, manufacturing methods applied in production and the quality assurance system.
Reading and following instructions provided in this manual will ensure safe and long lasting use of our tables.
General instructions:
1. This product must be operated by qualified and trained personnel who have thoroughlyread, understood and put
into practice all the precautionaryand operating instructions put forth in this operation manual.
2. Using, operating or servicing of the product contrary to the rules and recommendations put forth in this user
manual is prohibited, as it maylead to damage for which the manufacturer shall not be liable.
3. If the performance or parameters of the product are found to be inconsistent with what the operation manual
describes, you must stop using the product and inform the manufacturer or the reseller immediately.
4. Every repair of the product must be done by the manufacturer’s service or service authorized by the
manufacturer and registered on the repair list in the warranty card. Failure to do so will result in voiding the
warranty.
This warrantywill not be fulfilled if the product is used contraryto its purpose or fails to complywith the terms set in the
user manual.
CAUTION!
This sign denotes operations which –when performed in a way other than described in this manual
–may worsen the safety conditions or cause hazard to the user and/or the operator of the device.
A similar sign has been provided on the device in places where it is absolutely necessary to follow
the instructions provided in this Operation Manual
The manufacturer shall not be liable for the consequences of improper (i.e. against the instructions put forth in this
user manual) use of the GALAXYmassage tables!
All electric and electronic devices marked with the symbol of crossed-out dustbin must be
disposed-of properlyat recycling facilities according to the European Union’s WEEE directive
or equivalent regulations.
It is absolutelynecessary that all devices which contain substances harmful to the
environment or humans are recycled properly relevant facilities and must not be disposed of
with general or household waste.
Such regulations ensure that the quantity of electronic waste is reduced and a required
amount of electronic devices are recycled properly. Proper recycling of electronic waste is
important as it may contain substances harmful to the environment and humans.

Page 4 of 15
2014-05-19 GALAXY table - Manual En
2. FEATURES OF GALAXY MASSAGE TABLES
2.1. Usage
GALAXY massage tables are designed to be used in administration of the manual therapy
techniques and physiotherapy to heal or provide relief in injuries or other impairments by restoring
or improving the functions of the tissues, organs and systems.
GALAXY electrical massage tables [2 section headrest (type: MERCURY mod.: S2.Fx, S4.Fx, 2 section
backrest (type: MERCURY mod.: E-S2.Fx), 3 section (type JUPITER mod.: S3.Fx, S5.Fx) including the
relevant accessories] have been manufactured in conformity with essential requirements concerning
medical equipment (class I, rule 12) and are marked with CE mark, as per manufacturer’s declaration.
GALAXY hydraulic massage tables [2 section headrest (type: MERCURY mod.: S2.Fx-H, S4.Fx-H, 2
section backrest (type: MERCURY mod.: E-S2.Fx-H), 3 section (type JUPITER mod.: S3.Fx-H, S5.Fx-H)
including the relevant accessories] have been manufactured in conformity with essential requirements
concerning medical equipment (class I, rule 1) and are marked with CE mark, as per manufacturer’s
declaration
2.2. Technical data
Technical data
GALAXY
2 section headrest
(MERCURY)
2 section
backrest
(MERCURY)
3 section
(JUPITER)
S2.Fx
S4.Fx
E-S2.Fx
S3.Fx
S5.Fx
S2.Fx-H
S4.Fx-H
E-S2.Fx-H
S3.Fx-H
S5.Fx-H
Table length [cm]
head section
46
69
46
middle section
-
-
54
leg section
155
138
101
total
Approx. 202
Approx.209
Approx. 205
Inclination sections
head section
+40 / -70
+85/0 (optionally -20)
+40 / -70
middle section
-
-
-
leg section
-
-
+90/0
Electrical height
adjustment [cm]
min
50
max
101
Hydraulic height
adjustment [cm]
min
51
max
96
Table width [cm]
all sections
approx. 64
Weight [kg]
Not more than
115
Duty cycle
Continuous, short load (10%) max. 2 minutes „on”, min. 18 minutes „off” (electric
version only)
Lifting capacity [kg]
200 kg
(max safe load while adjusting height)
Working capacity [kg]
300 kg
(max safe load while not adjusting adjusting height)
Power and security
requirements
Voltage
230 VAC/50 Hz
(electric
models
only)
Current consumption
max. 1A
II, B
Protection level
Enclosure
IPX4
Ambient conditions
(temperature, relative
humidity, air pressure)
Work
+10 Cup to +40 C, from 30% to 75% non-condensing, 700-1060 hPa
Storage
+5 Cup to +45 C, not exceeding 75% non-condensing, 700-1060 hPa
Transport
-10 Cup to +45 C; from 20% to 95% non-condensing, 700-1060 hPa
Chart 1–Technical data of the GALAXY massage tables (Fx =type of bottom frame; H=hydraulic actuator)

2014-05-19 GALAXY table - Manual En
Page 5 of 15
2.3. GALAXY 2 SECTION HEADREST (MERCURY S2.Fx, S2.FX-H)
Head section inclination angle adjustment from 0 to +40 deg.
Length of the head section 46 cm
Head section declination angle adjustment from 0 to -70 deg.
Length of the leg section 155 cm
2.4. GALAXY 2 SECTION HEADREST, ADJUSTABLE ARMRESTS
(MERCURY S4.Fx, S4.Fx-H)
Head section inclination angle adjustment from 0 to +40 deg.
Length of the head section 46 cm
Head section declination angle adjustment from 0 to -70 deg.
Length of the leg section 155 cm
2.5. GALAXY 2 SECTION BACKREST (MERCURY E-S2.Fx, E-S2.Fx-
H)
Head section inclination angle adjustment from 0 to +85 deg.
Length of the head section 69 cm
Optionally, head section declination angle adjustment from
0 to -20 deg.
Length of the leg section 138 cm

Page 6 of 15
2014-05-19 GALAXY table - Manual En
2.6. GALAXY 3 SECTION (JUPITER S3.Fx, S3.Fx-H)
Head section inclination angle adjustment from 0to +40 deg. Length of the head section 46 cm
Head section declination angle adjustment from 0to -70 deg. Length of the middle section 54 cm
Leg section inclination angle adjustment from 0to +90 deg. Length of the leg section 101 cm
2.7. GALAXY 3 SECTION, ADJUSTABLE ARMRESTS (JUPITER S5.Fx,
S5.Fx-H)
Head section inclination angle adjustment from 0to +40 deg
Head section declination angle adjustment from 0to -70 deg.
Length of the head section 46 cm
Length of the middle section 54 cm
Leg section inclination angle adjustment from 0to +90 deg.
Length of the leg section 101 cm
CAUTION!
This manual covers all types of the GALAXY massage tables and not all information
and drawings will be relevant to your own massage table. The manufacturer reserves
itself a right to apply changes to the product not included in this version of manual
without reducing its functionalityor lowering safetyrequirements.

2014-05-19 GALAXY table - Manual En
Page 7 of 15
3. DESIGNAND FUNCTIONS
3.1. Table components
The frame of the table is made of welded steel sections coated with powder paint. It includes the
following components:
①lower frame
The Galaxy has a foot- operated height adjustment all-around switch frame in standard.
The Galaxy has the frame with 2 rollers and 2 in height adjustable feet in standard (F0
frame).
The Galaxy has 4 directable, retractable wheeling system with central brake as option (F4
frame).
The Galaxy has hydraulic height adjustment as option (-H).
②upper frame
Alladjustable sections are supported by a gas spring for inclination. To adjust the section relase
the gas spring by the handle.
③patient surface
allows patients to assume comfortable position for the massage with the possibility of
manual adjustment of inclination and declination angles of the head, middle and/or leg
sections (depending on the type of the table).
④head section
with angle adjustment and a breathing hole.
⑤access key
blocks the hi-lo height adjustment adjustment of the table (electric models only).

Page 8 of 15
2014-05-19 GALAXY table - Manual En
3.2. Additional accessories
Each GALAXY table is provided with a breathing hole in head section and has rails for fastening the
stabilizing belts in the leg section.
Additionally, the tables may be equipped with the following accessories:
- stabilizing bolsters and belts
- wedges: 30x40x12 cm and 50x35x20 cm
- rolls and semi-rolls 60x15 cm and 60x15x10 cm
- paper towel hanger (for rolls size 60x14cm max.)
Figure 2–mounting and unwinding paper towel roll
3.3. Table set
GALAXY table
as per order specs
User manual
1 pc.
Accessories
as per order specs
3.4. Transport and storage
Transport and storage conditions are described in table 1. The GALAXY line tables are transported to
the customer in a cardboard box on a wooden pallet. Stacking is permitted up to 3 layers using
special stackable pallets. External edges of the upholstered parts are lined with foam, bubble wrap
and stretch foil. Protect the outer edges of GALAXY tables against damage while moving or
transporting them.

2014-05-19 GALAXY table - Manual En
Page 9 of 15
4. SAFETY MEANS
Help the patient to maintain proper position before doing treatment procedures by lowering the bed
top to the lowest position. Likewise, lower the bed top after the treatment to help the patient to get out
of the bed.
5. PREPARING THE UNIT FOR USE
1. Select the place for the use of the table with a minimum of 80 cm clearance on each side of
the unit.
Figure 3-Recommended positioning of the GALAXY massage table
CAUTION!
When positioning or repositioning the table, pay special attention to ensure that there
are not any objects below the lower frame of the table. Always safeguard against
uncontrolled access of children or animals to the table or its location.
CAUTION!
Unplug the table from the mains socket (electric models) while performing
maintenance, servicing or similar actions under the table.
2. A suitable power supply connection must be available in the vicinity of the table with easy access
in case of emergency (electric models only).
CAUTION!
When connecting the suitable electrical power supply cable, make sure to protect it
from accidental clamping objects between moving parts of the table. The electrical
power supply cable should be laid in such a manner so as to prevent the patient or the
masseur from stumbling over it.
3. After locating the table in its destination place, unpack the unit from protective film and insert the
power cable plug in the suitable mains socket (electric models). The table is ready for operation.

Page 10 of 15
2014-05-19 GALAXY table - Manual En
CAUTION!
Do not use the table in rooms with high relative air humidity (especiallyin rooms meant
for hydro-therapeutictreatment).
6. OPERATING THE TABLE
Prepare a disposable bed cover (such as paper towels, disposable sheets etc.) for each patient
before attempting to use the GALAXY table for treatment procedures, especially when using
lubricants or other auxiliary substances (gels, oils, talcum powder, ointments, creams or lotions). The
patient should wear comfortable underwear and have their body covered for the whole time of
treatment except for those parts that are being massaged. Following this procedure helps to relax
and improve blood circulation prolonging the feeling of warmth in the massaged body parts.
6.1. Levelling the table
After the table has been located in its destination place, it should be levelled. This operation is
necessary to ensure proper working conditions of the unit. After the table has been located in its
destination place, when resting on its wheels, its feet should stay ca. 0.5 cm above the
floor (including its possible unevenness) –see 6.5
6.2. Height adjustment –raising (lowering) of the bed
Height adjustment in electrical GALAXY tables is done by means of a foot-controlled all-around
switch frame located at the bottom of the table. To lift the table, push the frame in the direction of the
head-rest / back-rest (marked as B in fig. 4 below). To lower it, push the frame in the direction of the
leg section (marked as A in the same picture). The table will be lifted or lowered as long as the foot
controller frame is kept in its leftmost or rightmost position. The actuator switches off automatically
when it reaches its minimum or maximum position.
In hydraulic models the hi-lo height adjustment is done via a foot-operated pedal in the lower frame.
Push the pedal down until the table reaches the desired height and lift the pedal to lower the table.
Figure 4-Control elements of the GALAXY massage table

2014-05-19 GALAXY table - Manual En
Page 11 of 15
A –down B –up C –lock handle
1. socket for stabilizing bolster in central section
2. two sockets for stabilizing bolsters in the head section (except mod. CLASSIC)
A –down; B –up
Figure 5 - Control elements of the GALAXY - H massage table
6.3. Adjustment of the adjustable section inclination/declination
In order to change the inclination/declination angle of any adjustable section of the table, pull the
release/lock handle of the gas spring to disengage it (see fig. 3 –item C), set the required position of
the section and release the handle to lock the spring again.
CAUTION!
Maintain proper distance from all moving elements of the table while adjusting the
height of position. Moving elements pose danger by creating pinch points.
6.4. Moving the table
1. GALAXY table with the F4 frame type has a foot lever (see C in fig. 4) which can be set in two
positions:
- WORK (A), with the table resting on its feet, which can be adjusted for levelling (by screwing the
foot in and out –see section 6.1)
- TRANSPORT (B), with the table resting on 4 castors enabling it to be transported
A –WORK,
B –TRANSPORT,
C –LIFTING LEVER
Figure 5–Moving the GALAXY F4 t
a b le

Page 12 of 15
2014-05-19 GALAXY table - Manual En
CAUTION!
Do not attempt to operate the lift lever with a patient on the table!
2. Lower frame with 2 rollers and 2 in height adjustable feet (F0 frame) has two feet at the head rest
side and two wheels at the opposite side. The table can be moved by lifting it by the head rest (be
careful not to press the gas spring lever nor the head/back-rest) and transport the table using the
two wheels.
CAUTION!
Do not attempt to move the table with a patient on it!
6.7. Access control (electric models only)
The GALAXY tables contain access control feature which blocks the unauthorized operation of the hi-
lo height adjustment.
Removing the key from the socket ❶will cause the LED light ❷to blink (0,7x/sec) and the
table’s actuator is blocked. Put the key❸back in the socket ❷this allows to use the table onal
again. The LED❹light contantely.
Blocked Wor ki ng
UWAGA
!
Hydraulic GALAXY tables perform only the push function to prevent accidental
clamping of the patient’s body.
CAUTION!
For electric tables remove the keyfrom its socked after work to prevent unauthorised use.

2014-05-19 GALAXY table - Manual En
Page 13 of 15
7. MAINTENANCE
CAUTION!
We recommend cleaning and/or disinfecting the upholstered surfaces and other parts of
the tables after each use to ensure proper hygiene level.
7.1. Cleaning the upholstery
1. Clean and maintain the upholstered surfaces in the following way:
- clean regularly with warm water and mild detergent (e.g. soap) solution; use soft cloth or
sponge
- rub the more heavily stained areas with a soft, damp brush
- after cleaning, wipe dry with a soft cloth
- in case the surface has been stained with ball pen ink, lipstick, printing ink etc., remove the
stain immediately by rubbing it with a soft cloth
2. Avoid extensive wetting of the surface of the table.
3. Disinfect the upholstery and other surfaces using the Incidin Foam or similar formula (available at
Meden-Inmed).
4. Never use:
- cleaning paste, wax, sprays
- strong detergents, solvents and cleaning agents containing solvents, cleaning preparations for
natural leather
Use of such preparations may cause stiffening and breakages of the cover material as
well as adverse change of the glossy finish of the upholstery surface which is not
covered by the warranty!
5. Sterilization with the use of the UV rays does not affect the surface of the upholstery.
CAUTION!
Before starting the cleaning of the table make sure that the electrical power supply cable
has been disconnected from the suitable mains supply in the room to prevent accidental
movement of the table!
7.2. Maintenance of the base and mechanical parts
1. Clean the metal parts with a soft, damp sponge. Wipe the parts dry immediately after cleaning..
2. All movable joints must be lubricated every six months or when experiencing squeaks or other
noise. We recommend using any available aftermarket penetrating lubricants. Protect
the upholstered parts from contact with the lubricants and remove any excess amounts or leaks of
these with a dry cloth.
3. Check the threaded joints periodically every six months and remove loose connections with a
Phillips screwdriver, hex keys (no 4 and 5) and flat spanners (10 and 19). Report all loose
connections that cannot be removed to the manufacturer’s authorized service and cease using the
table until the cause of the problem is removed.

Page 14 of 15
2014-05-19 GALAXY table - Manual En
7.3. Checking the gas springs
GALAXY tables are equipped with gas springs for easy adjustment of head section inclination
(all models) and leg section inclination angle (only 3 section models). To ensure proper
performance of the gas springs check the springs visually for leaks every 3 months. Any
perceived performance deficiency or leak must be reported to producer’s technical service
immediately.
7.4. Periodic check of electrical safety
The electrical safety check should be performed or ordered not less than once every 2 years, and
after every fault or repair of the actuator and/or the power mechanism of the massage table.

2014-05-20 GALAXY tables - Manual EN
Page 15 of 15
8. WARRANTYCARD
1. The validity period of this warranty is 24 months, starting from the date of purchase of
the equipment, as indicated in a proof of purchase. Upholstered parts are covered by a
12 month warranty. The warranty repairs can only be made by Meden-Inmed’s
authorised service teams.
2. Meden-Inmed is responsible for any faults whether in quality or quantity only if they have
been reported within 2 days following the delivery. It is the buyer’s responsibility to
inform Meden- Inmed of such faults within the period of 2 days after delivery.
3. A repair time exceeding 3 days, regardless of the reason that caused the delay, shall
result in the extension of the warranty period by a time that is equivalent to the total time
during which the device was out of order. The faulty or replaced parts are property of
Meden-Inmed’s Authorised service.
4. In case a subassembly that breaks down has already been repaired twice, the
manufacturer shall be obliged to replace a faulty subassembly with a new one.
5. The user shall be obliged to prepare a room and all necessary utilities needed for
operation of the device, so that they comply with requirements of obligatory standards
and with the installation manual and to conduct all the maintenance described in the
manual in order to benefit from the warranty coverage.
6. In case the installation and operation instructions have not been observed, the
manufacturer shall bear no responsibility for the safety of the user or patient during the
use of the unit.
7. Meden-Inmed shall bear no responsibility resulting for any loss, whether consequential
or incidental, including loss of profits or costs incurred by the fault in the equipment
covered by this warranty.
8. Faults that occurred within the warranty period and were not reported by the user in writing
(mail, fax, e-mail), shall not be covered by this
warranty.
9. Costs resulting from an unfounded claim shall be borne by the user.
10.The warranty shall not cover equipment:
i. damaged as a result of fire or lightning;
ii. with name plate, warranty seal and/or serial number or factory seals
removed or damaged;
iii. damaged due to its use in a manner other than defined in the
operation manual;
iv. where repairs or modifications have been done by unauthorized personnel;
v. damaged mechanically due to improper handling;
vi. damaged due to force majeure;
11. The user shall be obliged to ensure that both the equipment and its supply systems
are regularly maintained; failure to comply with this requirement may result in loss of
the user’s warranty rights.
12. In case the equipment covered by the warranty has been re-sold, there will be
no new warranty document issued. No duplicate warranty document will be
issued if lost.
13. The scope of this warranty does not cover parts and materials subject to normal
wear and tear.
14.This warranty does not exclude, limit or suspend your consumer statutory rights.