MEFE CAT 67106 User manual

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 1
[phone]
Free AU 1800 669 006
Instrucon Manual
Automac Urinal Valve
All-In-One
CAT 67106 | CAT 67106-1
Revision 9

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 2
[phone]
Free AU 1800 669 006
1. Product Descripon
This urinal ush valves uses a microcomputer controlled infrared sensor and solenoid valve for automac ushing. This device
is a hygienic bathroom soluon, eliminang risk of cross contaminaon and spread of bacteria. It has a sturdy a durable brass
body with a chrome plated nish for lustre and shine.
1.1 Specicaons
1.2 Diagrams
Parts Dimensions Baery Install
1.3 Pre-Installaon Instrucons
The height of the ushing valve and the distance of the urinal must be arranged in accordance
with dimensions on the right.
Water supply inlet is standard G 1/2”. Urinal must be top inlet with a minimum hole diameter of
12mm for the outlet pipe (dia 12mm).
Flush pipes of any silt and impuries.
Flushing Style 2 Stages (2s acvated on entry and 6s on departure)
2 Stages (Entry and departure 1—11 seconds (± 2 seconds) with oponal remote control CAT 67206R)
Sensing Range 10 – 65cm self adjusng
10—100cm (±10cm) with oponal remote control CAT 67206R
Working Pressure 0.07 to 0.7 Mpa
Connecons Standard ½” connecons
Dimensions Unit: 15.5 x 12 x 5.4cm
Packaged: 23 x 20 x 7cm, 1.2kg
Power Supply No electrical wiring required all-in-one unit – 4 x AA baery (90,000 starts) – baeries not supplied
Environment Humidity < 95%
Working Temperature 1—60°C
Water Flow 5 L/min

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 3
[phone]
Free AU 1800 669 006
2. Installaon
1. This unit requires a 1/2” water supply connecon (Figure 1).
2. Apply thread tape to the inlet thread. Place the decorave cover over the inlet valve and turn the ush valve clockwise
onto the pipe ng (Figure 2).
3. Aach the outlet pipe and insert though the urinal top inlet, placing the decorave cover over the urinal hole (Figure 3).
3. Operaon
Open the body cap at the top of the unit and insert the baeries.
Once power is acvated, return the top cap. The unit will automacally
begin sensing.
When a user approaches the sensor within range it will automacally
ush for approx. 2 seconds. When the user leaves the sensing range, it
will automacally ush again for approx. 6 seconds.
3.1 Push Buon (CAT 67106-1 only)
This device is equipped with a manual push buon if required.
Figure 1 Figure 2 Figure 3

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 4
[phone]
Free AU 1800 669 006
5. Exploded Diagram and Parts List
Item Part Descripon Material
1. 671-064 Baery Pack & Sensor assembly ABS Plasc
2. 671-062 Baery Case Holder ABS Plasc
3. 671-063 Cover Brass 59-1
4. 671-064 Sensor & Baery Pack Assembly Electronic Hardware/
ABS Plasc
5. 671-065 Screw 304 S/Steel
6. 671-066 Body Brass 59-1
7. 671-067 Screw 304 S/Steel
8. 671-068 Flow Adjustment Brass 59-1
9. 671-069 O-Ring NBR Rubber
10. 679-122B Solenoid SUS 304 Stainless +
POM Plasc + Rubber
11. 671-070 Washer 304 S/Steel
12. 671-071 Valve Body Brass 59-1
13. 671-072 Filter Brass 59-1
14. 671-073 Flat Seal NBR Rubber
15. 671-074 Bellow Brass 65
16. 671-075 Nut Brass 59-1
17. 671-076 Decorave Cover Brass 65
18. 671-077 Washer NBR Rubber
19. 671-078 Push Buon 304 S/Steel
Oponal remote to adjust sensing range or ush cycle: CAT 67206R
Item Descripon Material
10.3 Diaphragm NBR Rubber
10.4 Diaphragm Skeleton POM Plasc
10.5 Spring Needle 304 S/Steel
10.6 Seat POM Plasc
10.7 Glue Silicone Rubber
10.8 Core 430 Stainless
10.9 Spring 304 S/Steel
10.10 Set POM Plasc
10.11 Solenoid Valve Brass + Iron
10.12 Cover POM Plasc

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 5
[phone]
Free AU 1800 669 006
4. Exploded Diagram and parts list
5. Troubleshoong
No. Part Descripon Material
119-1Brass Nut—M39 x 1.5” Brass 59-1
219-2Spreader / Sleeve Plasc ABS
319-3Vacuum Breaker Insert Rubber NBR 70
419-4Brass Tube—M39 x 1.5” Brass 59-1
19-1
19-2
19-3
19-4
CAT 67VB
Issue Cause Soluons
No water Check if valve or power turns on, if its DC pow-
er, check if baeries need replacing. If by AC,
check plug has been connected correctly
Open water valve or turn power switch on. Take out face-
plate and retrieve the power supply and sensor. The LED
indicang lamp will ash 3 mes ( power connected)
Check sensor is not blocked by any obstacles There should be no obstacles within 100cm of sensor
Not enough me in front of sensor to acvate Flush will acvate 3 seconds aer user has approached
sensor. It will automacally ush aer the user leaves
Water leaking Water pressure too low Increase water pressure
Sand or impuries may get stuck in the seal
packing
Open the solenoid valve to clean any silt or sand out
DC baeries maybe at Change 4 x AA baeries to renew power
Water pressure too low Increase water pressureLow water ow
Water valve not open enough Turn water valve to full open posion
Filter is dirty Remove lter and clean