MegaLite DECO DRIVE CV4 User manual

USER MANUAL
Table of Contents
Safety Information 2
What Is Included 2
Specifications 3
Main Power Connection 4
DMX-512 Connection 4
12V By-Pass 4
Output Connection 5
Control Board 6
DMX Profile 7
Size & Weight 8
Cleaning & Maintenance 9
Parts List 9
Warranty 10
Customer Service 11

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
2. Do Not install the unit too close to a heat source.
3. Make sure cables are properly secured away from movement.
4. Maximum surface operating temperature is 148°F
5. Unit must not be left on for long periods of time.
Protection Against Electrical Dangers
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 4.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
5. The Unit must be installed in a well ventilated area.
6. Be sure ventilation slots are not blocked.
Protection Against Mechanical Hazards
1. Unit surface may reach high temperature. Allow about 5 minutes after powering the unit before
moving.
2. When repositioning rack ears make sure they are securely attached.
2
What is Included
1pc Deco Driver CV4
1pc Power Con Type Cable
4pc 5 Pin Screw Terminal Blocks
1pc 2 pin Screw Terminal Block
2pc Rear & Wall Support Rack Ears
1pc User Manual

3
Specifications
Part Numbers
Fixture
5065– Deco Driver CV4
Mechanical Specifications
Fastening System: Removable rack ears for Wall Mounting , Rack mounting and Rear rack mounting
Display: Digital
Power Connection: Power Con (type) Cable Mounted to Nema 5-15 head.
Housing: Black painted
DMX Connection: 5 Pin XLR & RJ45 in and out (optional 3 pin available)
Output Connection: 4 Port 5 pin Screw terminal & RJ45 output
Electrical Specifications
Power Input: 110-240VAC 5.9A 50/60 Hz
Outputs: 4
Power Per Output 96W
Total Max Power: 384W
Ballast: Electronic: Mean Well RSP-500-24
Sensor By Pass: 12V (to engage dimmer channels to full on)
Output: 24V
Drive Method: Constant Voltage
Working Ambient Temp: 24°f -148°f
Cooling: Silent, Convection Cooled
Refresh: 4,000Hz
Protocol: DMX 512
DMX 5 Modes:
1 Channel Mode Dimmer
2 Channel Mode Warm White, Cool White
3 Channel Mode R, G, B
4 Channel Mode R, G, B, W
7 Channel Mode Dimmer R, G, B, W, Strobe, Macro
Operating Mode: 22 Pre Programs, Stand alone via display
12V By Pass: Will engage all dimmer channels to full once receive a 12V signal
Control & Programming

4
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
DMX-512 Connection
The fixture is equipped with 5 pin XLR Sockets and RJ45 for DMX input and output. The sockets are wired in parallel.
Only use a shielded twisted pair cable designed for RS-485 and 5 pin XLR or RJ45 plugs and connectors in order to
connect the controller with the driver or the driver with another.
DMX 5 Pin —Input / Output Or RJ45 8 Pin— In / Output
1. Ground
2. Signal (-)
3. Signal (+)
1
3
2
4
5
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
RJ45 8 Pin
1. Signal (+)
2. Signal (-)
7&8. Ground
1 Signal +
2 Signal -
3 N/A
4 N/A
5 N/A
6 N/A
7 Ground
8 Ground
12V Sensor By-pass
Once the Deco Drive CV4 receives a DC 12V input signal all dimmer channels will go to a full position and by pass DMX
Control. Once 12V signal is removed the DMX Control will be reengaged.
12V input signal

5
Output Connection
Deco Driver CV4 is designed to be used as a driver for Constant Voltage lighting fixtures. There are many fixtures a
Deco Driver can control . Each of the 4 output can be individually controlled and addressed to use the same or different
fixture per each output. The Deco Lighting fixture manual will give you the information with power link limitations and
control type for that unit.
Fixtures that require Strip Cable connection will connect the input cables via 5Pin Screw terminal.
Use 20AWG cable or thicker for connections. Cables exceeding 100ft will have volt-
age drop. Voltage drop will result in intensity drop.
4 Ch Fixtures
DMX Control Mode
4 or 7CH
3 Ch Fixtures
DMX Control Mode
3 CH
2 Ch Fixtures
DMX Control Mode
2 CH
1 Ch Fixtures
DMX Control Mode
1 CH
Fixtures that require RJ45 connection will connect the input cables to RJ45 Output.
Use Cat6 A AWG 24 or thicker cable for cable connection with RJ45 connections. Ca-
bles exceeding 100ft will have voltage drop. Voltage drop will result in intensity drop.
Pin1 Red-
Pin 2 24V+
Pin 3 Green-
Pin 4 24V+
Pin 5 Blue-
Pin 6 24V+
Pin 7 Warm White-
Pin 8 24V+
4 Ch Fixtures
DMX Control Mode
4 or 7CH
Pin1 Red-
Pin 2 24V+
Pin 3 Green-
Pin 4 24V+
Pin 5 Blue-
Pin 6 24V+
Pin 7 N/A
Pin 8 N/A
3 Ch Fixtures
DMX Control Mode
3 CH
Pin1 Warm White-
Pin 2 24V+
Pin 3 Warm White-
Pin 4 24V+
Pin 5 Cool White-
Pin 6 24V+
Pin 7 Cool White-
Pin 8 24V+
2 Ch Fixtures
DMX Control Mode
2 CH
Pin1 White-
Pin 2 24V+
Pin 3 White-
Pin 4 24V+
Pin 5 White-
Pin 6 24V+
Pin 7 White-
Pin 8 24V+
1 Ch Fixtures
DMX Control Mode
1 CH

6
Control Board
System Mode
( DMX)
Port Mode DMX Address
(01) (01) (001)
DMX: DMX mode allows you to set the DMX
operational mode: For each output port you can
select Mode of operation and DMX start address.
Press Enter use the Up / Down button to select
the output port press Enter once selected. Mode
function will then be highlighted, use the Up /
Down button to select your operating mode.
Each lighting fixture will have a different operat-
ing mode. Consult the fixture’s manual or fixture
label to determine the operating mode. Press
Enter, DMX Address will then be highlighted,
use the Up / Down button to select the fixtures
start address. Start address should match your
controller’s start address channel. Press Enter
to confirm your settings.
Port Mode DMX Address
(02) (01) (001)
Port Mode DMX Address
(03) (04) (004)
Port Mode DMX Address
(04) (07) (210)
System Mode
( Auto)
Prog 01
(ST Color 1)
Auto: Auto mode allows you to access the
pre-built auto function for control. Press Enter
use the Up / Down button to select the pre pro-
gram fixture look. Programs 01 to 18 are single
scene programs and programs 19 to 21 are
chase programs. Press Enter once you have
decided on the scene or chase. For Programs 1-
18 use the Up/Down buttons to adjust fixture
dimmer output. For programs 19-21 use the Up/
Down buttons to adjust the chase speed. Press
Enter to confirm the fixture setting.
Prog 18
(ST Color 18)
Prog 19
(Step Chace)
Prog 20
(Color Fade)
“ “
Prog 21
(Strobe)
Prog 22
(Chasing)
Prog 01 Dimmer
(000)
Prog 18 Dimmer
(000)
Prog 19 Speed
(000)
Prog 20 Speed
(000)
“ “
Prog 22 Speed
(000)
Prog 22 Speed
(000)
System Mode
( Manual)
Red
(000)
Green
(000)
Blue
(000)
White
(000)
Manual: Manual mode allows you to man-
ually control the intensity of all 4 ports simultane-
ously via the control display without the need for
a DMX controller. Press Enter to select the dim-
mer output you would like to adjust . Use the Up/
Down keys to select the dimmer intensity. There
is many Deco Fixtures that can be controlled via
a Deco Driver. Please Consult your Deco Light-
ing fixtures Manual to see what values are ac-
tive. Press Enter to confirm the setting.
Lock Display: The display for the Deco Driver factory setting is lock screen function to unlock the display press and hold
the Menu & Enter for 3 seconds

7
DMX Profile
Deco CV4 1 Channel Mode
DMX Channel Function Description Value Init
1Dimmer LED Intensity 0-255 255
Deco CV4 2 Channel Mode
DMX Channel Function Description Value Init
1LED Color Warm White LED Intensity 0-255 255
2LED Color Cool White LED Intensity 0-255 255
Deco CV4 3 Channel Mode
DMX Channel Function Description Value Init
1LED Color Red LED Intensity 0-255 255
2LED Color Green LED Intensity 0-255 255
3LED Color Blue LED Intensity 0-255 255
Deco CV4 4 Channel Mode
DMX Channel Function Description Value Init
1LED Color Red LED Intensity (all outputs) 0-255 255
2LED Color Green LED Intensity (all outputs) 0-255 255
3LED Color Blue LED Intensity (all outputs) 0-255 255
4LED Color White LED Intensity (all outputs) 0-255 255
Deco CV4 7 Channel Mode
DMX Channel Function Description Value Init
1Dimmer Dimmer 0 to 100% 0-255 255
2LED Color Red LED Intensity (all outputs) 0-255 255
3LED Color Green LED Intensity (all outputs) 0-255 255
4LED Color Blue LED Intensity (all outputs) 0-255 255
5LED Color White LED Intensity (all outputs) 0-255 255
No Function 0-1
6Strobe Strobe (slow to fast) 2-127 0
Random Strobe (slow to fast) 128-255
No Function 0-1
7Macro Color Fade (slow to fast) 2-127 0
Color Chase (slow to fast) 128-255

8
Size & Weight
Fixture Size 19" X 10.37" X 1.75"
Fixture Packaged 21" X 12" X 3.75"
Net Weight 8.4lb
Gross Weight 9.5lb
19”
17.37”
1.75”
10.37”

Cleaning and Maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and
electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (rack, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
4) Ventilation ports must be clear of any debris.
5) Inner ventilation power supply fan must be clear of any debris
9
Rigging the Fixture
Caution!
1. The installation must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Installation location must have adequate air flow.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the Fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour without any failures. Installation should be
checked at least one time a year by a skilled person.
Parts List
5065PCBMAI MAIN PCB / DISPLAY
5065PCBDRI DRIVER PCB
5060PCBDMX5 5 PIN DMX PCB
5060PCBDMX3 3 PIN DMX PCB
5065PCB12V 12V PCB
5065POW MEAN WELL POWER SUPPLY UHP-500-24
5060FUS F5AL 250V 5X20MM FUSE
5060SWI ON/OFF SWITCH
5060HOURACREA WALL MOUNT & REAR RACK EARS
5065HOURACGOL GOLD FRONT RACK EARS
5060CONSCR 5 PIN SCREW TERMINAL CONNECTION
5065CONSCR2 2 PIN SCREW TERMINAL CONNECTION

All warranty claims are evaluated under the terms of this limited warranty. If a product falls within the warranty period and if, upon examination by MSI
it is found to have failed for a covered cause, MSI will, at its sole discretion, repair or replace the defective part or product or reimburse the purchaser
a pro-rated portion of the purchase price based on the percentage of the warranty period still remaining as of the date that the returned product was
received by MSI. Should a replacement part or product be discontinued or unavailable, MSI reserves the right, in its sole and absolute discretion, to
substitute a comparable replacement part or product for the defective part or product. MSI warranty obligation hereunder is limited solely to the repair or
replacement of or reimbursement for the particular parts or products determined by MSI to have failed for a covered cause within the warranty period.
In no event shall MSI be responsible to replace or reimburse purchaser for any products or portions of a system that MSI determines has not failed for a
covered cause within the warranty period, even if such other products or portions of a system are used together with products being repaired or replaced
by MSI under this warranty and the repaired product differs in brightness, colors or any other attribute after the repair.
Costs of removal, shipping to MSI or its authorized representative and reinstallation are solely the responsibility of the purchaser. If MSI determines that
the product is covered by this limited warranty, it will only pay for parts and labor as indicated by product type. If MSI determines that the product is not
covered by this limited warranty, the purchaser will have the option of paying for the repair (if the product can be repaired) and the purchaser shall be
responsible for the cost of shipping the repaired product back to the purchaser. MSI reserves the right, in its sole and absolute discretion, to decline any
repair.
Product / Series Warranty Period Coverage
BATTERY POWERED LED Six month battery one year all other components 1, 2
MOVING LED, HAZERS One Year 2
OUTDOOR IP RATED LED Two Years 3
HOUSE LIGHT LED, DECORATIVE LED, COMPACT LED, iCANDY LED, THEATRICAL LED, STROBE WASH LED, Three Years 4
FOLLOW SPOT LED, PRODUCTION & HOUSE OF WORSHIP CONTROL, ARCHITECTURAL CONTROL,THEATRICAL
CONTROL, DANCE VENUE & MOBILE DJ CONTROL, DIRECT VIEW LED DISPLAYS, AND MV CONTROLERS
1. Battery, 183 days six months 2. Parts and Labor, 365 days one year 3. Parts and Labor, 730 days two year 4. Parts and Labor, 1095 days three year
This limited warranty excludes any defects caused by, resulting from or relating to the following:
Normal wear and tear of lamps, color media, brushes, contact rings, lamp sockets, belts and other parts prone to wear and tear.
Misuse, abuse, improper handling, accident, alteration or attempts to repair by or on behalf of the owner or any person not authorized by MSI.
Damage to the product resulting from acts of God, including, but not limited to, earthquakes, hurricanes, tornados, lightning and other natural disasters, re, explosion, ood, riots, civil disorder
or any other cause beyond the reasonable control of MSI.
Exposure to harsh or excessively corrosive environmental conditions (whether indoors or outdoors), including, but not limited to, extreme temperatures, humidity, atmospheric conditions
(including salinity or pressure), radiation (UV, infrared or nuclear), shock and conditions which exceed the product’s Ingress Protection (“IP)” rating.
Use of the product in a manner which exceeds the applicable product specication, including, but not limited to, exposure to excessive, insufcient or other voltage conditions.
Installation or use of the product not in accordance with the technical documentation, MSI guidelines (as may be posted on its website at www.megasystemsinc.com from time to time or
otherwise designated by MSI or its brands) or applicable building and electrical codes, regulations and standards.
Failure to maintain the product in accordance with the technical documentation.
Natural degradation and color shift of the LED source over the course of normal product use.
Slight deviations in the specied values of intensity and color that do not affect the functionality of the product.
Use of the product not for its intended purpose.
IN NO EVENT SHALL MEGA SYSTEMS, INC. BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR PUNITIVE LOSS OR DAMAGE OF
ANY KIND, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUES, LOSS OF USE OF THE PRODUCT OR ANY OTHER GOODS OR ASSOCI-
ATED EQUIPMENT, DAMAGE TO ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE PRODUCTS, FACILITIES OR SERVICES, DOWN
TIME COST, INSTALLATION OR LABOR COSTS, OR CLAIMS OF THE PURCHASER’S CUSTOMERS, WHETHER BASED ON WARRANTY, CONTRACT OR NEG-
LIGENCE, ARISING IN CONNECTION WITH THE SALE, USE OR REPAIR OF THE PRODUCT. MEGA SYSTEMS INC’S MAXIMUM LIABILITY SHALL NOT, IN ANY
CASE, EXCEED THE PURCHASE PRICE OF THE PRODUCT THAT GIVES RISE TO THE CLAIM.
EXCEPT FOR THE LIMITED WARRANTY SET FORTH HEREIN, ALL PRODUCTS SOLD BY MEGA SYSTEMS, INC. ARE SOLD “AS IS” WITHOUT ANY WARRANTY,
EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ALL OF WHICH ARE EXPRESSLY AND SPECIFICALLY DISCLAIMED BY MEGA SYSTEMS, INC.
WARRANTY FOR PRODUCTS PURCHASED AFTER JANUARY 1, 2021
MEGA SYSTEMS INC (“MSI”) hereby warrants to the original purchaser/owner (“Customer”), MSI products to be free of manufacturing defects in material and workmanship, for the warranty periods
as dened below from the original purchase invoice date. This warranty applies exclusively to new MSI branded and/or distributed products listed below, purchased from an MSI AUTHORIZED dealer/
reseller. This warranty is not transferable and may or may not apply to products sold and/or forwarded outside the United States. Please contact MSI for applicable regional product warranty information.
The purchase of MSI product constitutes the Customer’s acceptance of all warranty terms and conditions as listed in this limited warranty statement. This warranty provides the Customer with legal rights
which may vary from state to state. Please contact MSI regarding warranty questions prior to purchasing.
10

MEGA-Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [email protected]g
Customer Support
Document
Version Date Fixture Software Notes
1.1 05/27/2021 V1.3 Updated 5065 Version
MEGA-Lite has a customer support line to provide set up help and to answer any question should you encounter a
problem. Please visit our website for any other related technical documents. For service related issues, please contact
our service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [email protected]ing
Manual Version
Please visit www.mega.lighting for the most up to date manual version.