Melissa & Doug PARKING GARAGE User manual

We care about your comments.
Please call us! 1-800-284-3948
2008 Melissa & Doug, LLC
All Rights Reserved
ITEM #4595
PARKING GARAGE
ASSEMBLY INSTRUCTIONS
www.MelissaAndDoug.com
!
!
WARNING:
CAUTION:
CHOKING HAZARD -
Small parts.
Not for children under 3 years.
Adult assembly required.

BASE
BASE RAMP
1 piece
3 ELEVATOR
1 piece
4
5
6
8
Phillips Screwdriver
Bag
4 pieces
LARGE SCREW
PARKING GARAGE
PARTS
12
7
1st FLOOR
2nd FLOOR
3rd FLOOR
FLOOR RAMPS
ATTENDANT'S
BOOTH
CAR WASH
GAS PUMP CAR
ATTENDANT TOOLS NEEDED
RAMP CONNECTOR
LOWER PILLAR UPPER PILLAR
SMALL SCREW LARGE BOLT
Screws and Bolts shown actual size
Bag B C Bag
10 pieces 6 pieces
A Bag
5 pieces
Bag D E
2 pieces
1 piece
1 piece
1 piece
1 piece
1 piece
2 pieces
1 piece
1 piece 1 piece
2 pieces
Note: Bags may contain extra parts
for your convenience.
SMALL BOLT
Bag F
1 Piece
Bag F
2 pieces
2

Attach the Base Ramp to the
Base (1) with a Small Bolt from
Bag (F).
Do not tighten completely at
this time.
PARKING GARAGE
STEP 1
STEP 3
STEP 2
Attach one connector (A)
to the Base Ramp (2) with
one Small Screw from
bag (B)
Attach two Lower Pillars (D) as shown
using two Large Bolts (C) from under
the Base.
3

PARKING GARAGE
STEP 4
STEP 5
Attach the Elevator (3) shown here
using two Large Bolts (C) from
under the Base.
Slide the 1st Floor (4) into the
bottom grooves on the Elevator.
Make sure it is all the way in and
resting on the Lower Pillars.
4

D
STEP 6
STEP 8
STEP 7
B
PARKING GARAGE
Fasten the 1st Floor with two Upper Pillars (E)
as shown here by turning the screw end through
the floor and into the Lower Pillars.
Fasten the Connector that was attached to
the ramp in Step 1 using a Small Screw (B).
Tighten the Large Bolt under the ramp now.
Slide the 2nd Floor (5) into the elevator
as shown and allow it to rest on the Pillars.
Fasten the 2nd Floor using
two Upper Pillars (E).
Align and start both pillars through the
floor before tightening completely.
Align and start both pillars through the
floor before tightening completely.
5

PARKING GARAGE
STEP 9
STEP 10
Slide the 3rd Floor (6) into the
elevator shown here.
Fasten the 3rd Floor using
two Large Bolts (C) through
the floor and into the Pillars.
Align and start both Bolts
through the floor before
tightening completely.
6

B
E
NOTE: The "countersink" (angled hole)
should be on the top side where the
screw goes in first.
The Part Number label will be on the
bottom side of the part.
PARKING GARAGE
STEP 11
STEP 12
Attach two Connectors (A) using
two Small Screws (B) to one of
the Floor Ramps (7).
Place the Floor Ramp with the Connectors
between the 2nd and 3rd Floors and
attach using two Small Screws (B)
7

C
F
NOTE: The "countersink" (angled hole)
should be on the top side where the
screw goes in first.
The Part Number label will be on the
bottom side of the part.
PARKING GARAGE
STEP 13
STEP 14
Attach the last two connectors (A)
to another Floor Ramp (7) using
two Small Screws (B)
Attach this Floor Ramp between
the 1st and 2nd Floors using two
Small Screws (B)
8

Fit the Attendant's Booth (8) to the
base using 2 Large Screws (F).
PARKING GARAGE
STEP 15
Your Parking Garage and all its accessories
are now ready for play!
9