Mensela ED-LS1 User manual


BrandMensela
ModelED-LS1
Ratedvoltage(v=)12
BatterytypeLithium-ion
No-loadspeed(rpm)0-350/0-1350
Maxclutch(mm)10
Maxscrewdiameter(mm)8
Drillweight（kg）1.15
Chargerinput(V)110-260v
Frequency(Hz)50-60
Allowabletemperature0-50(℃)
Manufacturerreservestherighttochangespecificationswithoutnotice.
Specificationsmaydifferfromcountrytocountry.
      
                  

(FORALLBATTERYOPERATEDTOOLS)
      

Readandunderstandallinstructions.Failuretofollowallinstructionslistedbelow,mayresultinelectricshock,fire
and/orseriouspersonalinjury.
1.Keepyourworkareacleanandwelllit.Clutteredbenchesanddarkareasinviteaccident.
2.Donotoperatepowertollsinexplosiveatmos-pheres,suchasinthepresenceofflammableliquids,ordust.Power
toolscreatesparkswhichmayignitethedustorfumes.
3.Keepbystanders,children,andvisitorsawaywhileoperatingapowertools.Distractionscancauseyoutolosecontrol.
Electricalsafety
4.Abatteryoperatedtollwithintegralbatteriesoraseparatebatterypackmustberechargedonlywiththespecified
chargerforthebattery.Achargerthatmaybesuitableforonetypeofbatterymaycreateariskoffirewhenusedwith
anotherbattery.
5.Usebatteryoperatedtoolonlywithspecificallydesignatedbatterypack.Useofanyotherbatteriesmaycreate
ariskoffire.
PersonalSafety
6.Stayedalert,watchwhatyouaredoing,andusecommonsensewhenoperatingapowertool.Donotusetoolwhile
tiredorundertheinfluenceofdrugs,alcohol,ormedication.Amomentofinattentionwhileoperatingpowertools
mayresultinseriouspersonalinjury.
7.Dressproperly.Donotwearlooseclothing,orhaveunprotectedhair.Keepyourhair,clothing,andglovesaway
frommovingparts.Looseclothes,jewelry,orlonghaircanbecaughtinmovingparts.
8.Avoidaccidentalstarting.Besureswitchisinthelockedoroffpositionbeforeinsertingbatterypack.Carryingtools
withyourfingerontheswitchorinsertingthebatterypackintoatoolwiththeswitchoninvitesaccidents.
9.Removeadjustingkeysorwrenchesbefore
turningthetoolon.Awrenchorakeythatisleftattachedtoarotatingpartofthetoolmayesultinpersonalinjury.
10.Donotoverreach.Keepproperfootingandbalanceatalltimes.Properfootingandbalanceenablebettercontrol
ofthetoolinunexpectedsituations.
11.Usesafetyequipment.Weareyeprotection.Dustmask,non-skidsafetyshoes,hardhat,orhearingprotectionmust
beusedforappropriateconditions.
ToolUseandCare
12.Useclampsorotherpracticalwaytosecureandsupporttheworkplacetoastableplatform.Holdingtheworkby
handoragainstyourbodyisunstableandmayleadtolossofcontrol.
13.Donotforcetool.Usethecorrecttoolforyourapplication.Thecorrecttoolwilldothejobbetterandsaferatthe
rateforwhichitisdesigned.


14.Donotusetoolifswitchdoesnotturnitonoroff.Atoolthatcannotbecontrolledwiththeswitchisdangerous
andmustberepaired.
15.Disconnectbatterypackfromtoolorplacetheswitchinthelockedoroffpositionbeforemakinganyadjustments,
changingaccessories,orstoringthetool.Suchpreventivesafetymeasuresreducetheriskofstartingthetoolaccidentally.
16.Storeidletoolsoutofreachofchildrenandotheruntrainedpersons.Toolsaredangerousinthehandsofuntrained
users.
17.Whenbatterypackisnotinuse,keepitawayfromothermetalobjectslike:paperclips,coins,keys,nails,screws,or
othersmallmetalobjectsthatcanmakeaconnectionfromoneterminaltoanother.Shortingthebatteryterminals
togethermaycausesparks,burns,orafire.
18.Maintaintoolswithcare.Keepcuttingtoolssharpandclean.Properlymaintainedtoolswithsharpcuttingedgeare
lesslikelytobindandareeasiertocontrol.
19.Checkformisalignmentorbindingofmovingparts,breakageofparts,andanyotherconnectionthatmayaffectthe
toolʼsoperation.Ifdamaged,havethetoolservicedbeforeusing.Manyaccidentsarecausedbypoorlymaintainedtools.
20.Useonlyaccessoriesthatarerecommendedbythemanufacturerforyourmodel.Accessoriesthatmaybesuitablefor
onetoolmaycreateariskforinjurywhenusedonanothertool.
SERVICE
21.Toolservicemustbeperformedonlybyqualifiedrepairpersonnel.Serviceormaintenanceperformedbyunqualified
personnelmayresultinariskofinjury.
22..Whenservicingatool,useonlyidenticalreplacementparts.FollowinstructionsintheMaintenancesectionofthis
manual.UseofunauthorizedpartsorfailuretofollowMaintenanceinstructionsmaycreateariskofshockinjury.

                  
DONOTletcomfortorfamiliaritywithproduct(gainedfromrepeateduse)replacestrictadherencetocordlessdrill
safetyrules.Ifyouusethistoolunsafelyorincorrectly,youcansufferseriouspersonalinjury.
1.Holdtoolbyinsulatedgrippingsurfaceswhenperforminganoperationwherethecuttingtoolmaycontact
hiddenwiring.Contactwitha“live”wirewillalsomakeexposedmetalpartsofthetool“live”andshocktheoperator.
2.Beawarethatthistoolisalwaysinanoperatingcondition,becauseitdoesnothavetobepluggedintoanelectrical
outlet.
3.Alwaysbesureyouhaveafirmfooting.
4．Besurenooneisbelowwhenusingthetoolinhighlocations.
5.Holdthetoolfirmly.
6.Keephandsawayfromrotatingparts.
7.Donotleavethetoolrunning.Operatethetoolonlywhenhand-held.
8.Donottouchthedrillbitortheworkpieceimmediatelyafteroperation,theymaybeextremelyhotandcouldburn
yourskin.
9.Somematerialcontainschemicalswhichmaybetoxic.Takecautiontopreventworkingdustinhalationandskin
contact.Followmaterialsuppliersafetydata.
      
Thefollowingshowthesymbolsusedfortool.
V……………voltsno………..……..noloadspeed
………..directcurrent…/min…….revolutionsorreciprocationperminute

                                 
1.Beforeusingbatterycartridge,readallinstructionsandcautionarymarkingson(1)batterycharger,(2)battery,
and(3)productsusingbattery.
2.Donotdisassemblebatterycartridge.
3.Ifoperatingtimehasbecomeexcessivelyshorter,stopoperatingimmediately.Itmayresultinariskofoverheating,
possiblebumsandevenanexplosion.
4.Ifelectrolytegetsintoyoureyes,rinsethemoutwithcleanwaterandseekmedicalattentionrightaway.Itmay
resultinlooseofyoureyesight.
5.Alwayscoverthebatteryterminalswiththebatterycoverwhenthebatterycartridgeisnotused.
6.Donotshortthebatterycartridge.
(1)Donottouchtheterminalswithanyconductivematerial.
(2)Avoidstoringbatterycartridgeinacontainerwithothermetalobjectssuchasnails,coins,etc.
(3)Donotexposebatterycartridgetowaterorrain.Abatteryshortcancausealargecurrentflow,overheating,
possiblebumsandevenabreakdown.
7.Donotstorethetoolandbatterycartridgeinlocationswherethetemperaturemayreachorexceed55℃(122oF)
8.Donotincineratethebatterycartridgeevenifitisseverelydamagedoriscompletelywornout.Thebatterycartridge
canexplodeinafire.
9.Becarefulnottodroporstrikebattery
                                 
1.Beforeusingbatterycartridge,readallinstructionsandcautionarymarkingson(1)batterycharger,(2)battery,
and(3)productsusingbattery.
2.CAUTION:Toreduceriskofinjury,chargeonlythelithium-ionbatterywiththiskit.Othertypesofbatteriesmay
burst,causingpersonalinjuryanddamage.
3.Non-rechargeablebatteriescannotbechargedwiththisbatterycharger.
4.Useapowersourcewiththevoltagespecifiedonthenameplateofthecharger.
5.Donotchargethebatterycartridgeinpresenceofflammableliquidsorgases.
6.Donotexposechargertorainorsnow.
7.Nevercarrychargerbycordofyankittodisconnectfromreceptacle.
8.Afterchargingorbeforeattemptinganymaintenanceorcleaning,unplugthechargerfromthepowersource.
Pullbyplugratherthancordwheneverdisconnectingcharger.
9.Makesurecordislocatedsothatitwillnotbesteppedon,trippedover,orotherwisesubjectedtodamageorstress.
10.Donotoperatechargerwithdamagedcordorplug-replacethemimmediately.
11.Donotoperateordisassemblechargerifithasreceivedasharpblow,beendropped,orotherwisedamaged
inanyway,takeittoaqualifiedserviceman.Incorrectuseorreassemblymayresultinariskofelectricshockorfire.
12.Thebatterychargerisnotintendedforusebyyoungchildrenorinfirmpersonswithoutsupervision.
13.Youngchildrenshouldbesupervisedtoensurethattheydonotplaywiththebatterycharger.
14.DonotchargebatterycartridgewhentemperatureisBELOW10℃(50oF)orABOVE40℃(104oF).
15.Donotattempttouseastep-uptransformer,anenginegeneratororDCpowerreceptacle.

                        
1.Chargethebatterybeforecompletelydischarged.Alwaysstoptooloperationandchargethebatterywhenyou
noticelesstoolpower.
2.Neverrechargeafullychargedbatterycartridge.Overchargingshortenthebatteryservicelife.
3.Chargethebatterywithroomtemperature10℃-40℃(50oF‒104oF).Letahotbatterycooldownbeforechargingit.
4.ChargetheLithium-ionbatterywhenyoudonotuseitformorethansixmonths.
        
        
1.Button
2.Batterycartridge
      
.Alwaysbesurethatthetoolswitchedoffandthebatterycartridgeisremovedbeforeadjustingorchecking
functiononthetool.
                      
.Alwaysswitchoffthetoolbeforeinsertionorremovalofthebatterycartridge.
.Toremovethebatterycartridge,withdrawitfromthetoolwhilepressingthebuttonsonbothsidesofthecartridge.
.Toinsertthebatterycartridge,alignthetongueonthebatterycartridgewiththegrooveinthehousingandslip
itintoplace.Alwaysinsertitallthewayuntilitlocksinplacewithalittleclick.Ifnot,itmayaccidentallyfalloutof
thetool,causinginjurytoyouorsomeonearoundyou.
.Donotuseforcewheninsertingthebatterycartridge.Ifthecartridgedoesnotslideineasily,itisbeinginserted
correctly.
1.Switchtrigger

      
.Beforeinsertingthebatterycartridgeintothetool,alwayschecktoseethattheswitchtriggeractuates
properlyandreturnstothe“OFF”positionwhenreleased.
Tostartthetool,simplypulltheswitchtrigger.Toolspeedisincreasedbyincreasingpressureontheswitchtrigger.
Releasetheswitchtriggertostop.
       
.Thistoolisequippedwithanelectricbrake.Ifthetool
consistentlyfailstoquicklystopafterswitchtrigger
release,havetoolservicedataservicecenter.
                
.Thistoolhasareversingswitchtochangethedirectionofrotation.Depressthereversingswitchlever
fromtheRsideforclockwiseorfromtheLsideforneutralposition,theswitchtriggercannotbepulled.
     
.Alwayscheckthedirectionofrotationbeforeoperation.
.Usethereversingswitchonlyafterthetoolcomestoacompletestop.Changingthedirectionofrotation
ofbeforethetoolstopsmaydamagethetool.
.Whennotoperatingthetool,alwayssetthereversingswitchlevertotheneutralposition.
1.Lamp
1.Graduations
2.Adjustingring
3.Drillmarking
4.Pointer
.Donotlookinthelightorseethesourceoflightdirectly.
Pulltheswitchtriggertolightupthelamp.Thelampkeeps
onlightingwhiletheswitchtriggerisbeingpulled.
.Useadryclothtowipethedirtoffthelensoflamp.Becareful
nottoscratchthelensoflamp,oritmaylowertheillumination.
                
     
                    
Thefasteningtorquecanbeadjustedin19stepsbyturning
theadjustingringsothatitsgraduationsarealignedwiththe
pointeronthetoolbody.Thefasteningtorqueisminimum
whenthenumber1isalignedwiththepointer,andmaximum
whenthemarkingisalignedwiththepointer.Theclutchwill
slipatvarioustorquelevelswhensetatthenumber1to18.
Theclutchisdesignednottoslipatthemarking.
Beforeactualoperation,driveatrialscrewintoyourmaterial
orapieceofduplicatematerialtodeterminewhichtorque
levelisrequiredforaparticularapplication.

    
.Theadjustingringdoesnotlockwhenthepointerispositionedonlyhalfwaybetweenthegraduations.
.Donotoperatethetoolwiththeadjustingringsetbetweenthenumber18andthe
marking.Thetoolmaybedamaged.
      
..Alwaysbesurethatthetoolisswitchedoffandthebatterycartridgeisremovedbeforecarryingout
anyworkonthetool.
                       
.Holdtheringandturnthesleevecounterclockwisetoopenthechuckjaws.placethebitinthechuckasfarasit
willgo.Holdtheringfirmlyandturnthesleeveclockwisetotightenthechuck.
Toremovethebit,holdtheringandturnthesleevecounter-clockwise.
Placethepointofthedriverbitinthescrewheadandapplypressuretothetool.Startthetoolslowlyandthen
increasethespeedgradually.Releasetheswitchtriggerassoonastheclutchcutsin.
                       
Placethepointofthedriverbitinthescrewheadandapply
pressuretothetool.Startthetoolslowlyandthenincrease
thespeedgradually.Releasetheswitchtriggerassoonas
theclutchcutsin.
      
.Makesurethatthedriverbitisinsertedstraightinthescrew
head,orthescrewand/orbitmaybedamaged.
    
.Whendrivingwoodscrews,predrillpilotholestomake
drivingeasierandtopreventsplittingoftheworkpiece.
Seethechart.
         
.First,turntheadjustingring,sothatthepointerpointsto
themarking.Thenproceedasfollows.
        
Whendrillinginwood,thebestresultsareobtainedwithwood
drillsequippedwithaguidescrew.Theguidescrewmakes
drillingeasierbypullingthebitintotheworkpiece.
        
Topreventthebitfromslippingwhenstartingahole,makean
indentationwithacenter-punchandhammeratthepointto
bedrilled.
Placethepointofthebitintheindentationandstartdrilling.
Useacuttinglubricantwhendrillingmetals.Theexceptions
areironandbrasswhichshouldbedrilleddry.

      
.pressingexcessivelyonthetoolwillnotspeedupthedrilling.Infact,thisexcessivepressurewillonlyserveto
damagethetipofyourbit,decreasethetoolperformanceandshortentheservicelifeofthetool.
.Thereisatremendousforceexertedonthetool/bitatthetimeofholebreakthrough.Holdthetoolfirmlyandexert
carewhenthebitbeginstobreakthroughtheworkpiece.
.Astuckbitcanberemovedsimplybysettingthereversingswitchtoreverserotationinordertobackout.However,
thetoolmaybackoutabruptlyifyoudonotholeitfirmly.
Alwayssecuresmallworkpiecesinaviseorsimilarholddowndevice.
.Ifthetoolisoperatedcontinuouslyuntilthecatterycartridgehasdischarged,allowthetooltorestfor
15minutesbeforeproceedingwithafreshbattery.
      
                                 
1.PlugthebatterychargerintotheproperACvoltagesource.Thecharginglightwilllighteningreencolor.
2.Insertthechargerplugintothebattery.,thecharginglightwillturnredifthebatteryrunslow.
3.Whenthecharginglightturnsredtogreen,thechargingcycleiscomplete.
4.Aftercharging,unplugthechargerfromthepowersource.
      
Thebatterychargerisforchargingthelithium-ionbatterywiththiskit.Neveruseitforotherpurposesorforother
manufacturerʼsbatteries.
.Whenyouchargeabatterycartridgewhichisneworhasnotbeenusedforalongperiodoftime,itmaynot
acceptafullchargeuntilafterdischargingitcompletelyandrechargingacoupleoftimes.
.Ifyouchargeabatteryfromajustoperatedtoolorabatterywhichhasbeenexposedtodirectsunlightorheat
foralongtime,thecharginglightmaylighteninredcolor.Ifthisoccurs,waitforawhile.Chargingwillbegin
afterthebatterycools.
         
      
.Alwaysbesurethatthetoolisswitchedoffandthebatterycartridgeisremovedbefore
attempttoperforminspectionormaintenance.
TomaintainproductSAFETYandRELIABLITY,repairs,anyothermaintenanceoradjustment
shouldbeperformedbyProfessionalServiceCenter,alwaysusingourreplacementparts.