Menumaster DECS11MA User manual

Microwave Oven
Service Manual
DECS11MA
DES11EA
DFS11G
DFS11EA
UCS11MA
US11EA
UFS11EA
CAUTION
BEFORE SERVICING THE UNIT, READ THE
SAFETY PRECAUTIONS IN THIS MANUAL

This device is to be serviced only by properly qualified service personnel
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be
taken to avoid possible exposure to excessive microwave energy
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
A) Do not operate or allow the oven to be operated with the door open
B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse
C) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections
D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation
and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner
E) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner
SAFETY PRECAUTIONS

(Page)
SAFETY PRECAUTIONS --------------------------------------------------------------------- Inside fr nt c ver
SPECIFICATIONS
----------------------------------------------------------------------------------------------------- 1-1
CAUTIONS
-------------------------------------------------------------------------------------------------------------- 2-1
INSTALLATIONS
------------------------------------------------------------------------------------------------------ 3-1
OPERATING INSTRUCTIONS
------------------------------------------------------------------------------------ 4-1
COOKING DISPLAYS --------------------------------------------------------------------------------------------------------- 4-5
PROGRAMMING DISPLAYS ------------------------------------------------------------------------------------------------
4-5
OPERATION
----------------------------------------------------------------------------------------------------------------------- 4-6
PROGRAMMING ---------------------------------------------------------------------------------------------------------------- 4-7
SCHEMATIC DIAGRAM ------------------------------------------------------------------------------------------------------ 4-9
CIRCUIT DESCRIPTION --------------------------------------------------------------------------------------------------- 4-10
SERVICE INFORMATION
------------------------------------------------------------------------------------------
5-1
TOOLS AND MEASURING INSTRUMENTS --------------------------------------------------------------------------- 5-1
MICROWAVE LEAKAGE TEST -------------------------------------------------------------------------------------------- 5-1
MEASUREMENT OF MICROWAVE POWER OUTPUT
----------------------------------------------------------- 5-3
DISASSEMBLY AND ADJUSTMENT
------------------------------------------------------------------------------------- 5-3
INTERLOCK CONTINUITY TEST
------------------------------------------------------------------------------------------ 5-7
COMPONENT TEST PROCEDURE -------------------------------------------------------------------------------------- 5-8
TROUBLE SHOOTING
------------------------------------------------------------------------------------------------------ 5-11
EXPLODED VIEW ----------------------------------------------------------------------------------------------------- 6-1
SCHEMATIC DIAGRAM OF P.C.B.
------------------------------------------------------------------------------ 7-1
PRINTED CIRCUIT BOARD ------------------------------------------------------------------------------------------------- 7-2
CONTENTS

1-1
SPECIFICATIONS
This microwave oven is designed for commercial use only
It is not recommended for built-in installation
ITEM
MODEL
Power Requirement
Power Output
Microwave Frequency
Magnetron
Timer
Outside Dimensions
Cavity Dimensions
Net Weight
Shipping weight
Control Complement
Nameplate Location
DESCRIPTION
230 Volts AC 50 Hz
1,600 Watts
Single phase, 3 wire grounded
1,100 Watts full microwave power (IEC60705)
2,450 MHz
2M282
0 ~ 60 min
213/4”(W) x 141/4”(H) x 177/8”(D)
141/4”(W) x 87/8”(H) x 163/8”(D)
51 kg
58 kg
Touch Control System
Clock : 00 ~ 60
Microwave Power for Variable Cooking
Power level
HIGH-------------------------------------------Full power throughout the cooking time
70% (Med -High)
--------------------
approx 70% of Full power
50% (Med -Low)----------------------------approx 50% of Full power
20% (Low)------------------------------------approx 20% of Full power
Back Side
DECS11MA / DES11EA
DFS11G / DFS11EA UCS11MA / US11EA UFS11EA
240 Volts AC 50 Hz
1,700 Watts

• DO NOT operate on a 2-wire extension cord during
repair and use
• NEVER TOUCH any oven components or wiring during
operation
• BEFORE TOUCHING any parts of the oven, always
remove the power plug from the outlet
• For about 30 seconds after the oven stops, an electric
charge remains in the high voltage capacitor When
replacing or checking, you must discharge the high
voltage capacitor by shorting across the two terminals
with an insulated screwdriver
• Remove your watches whenever working close to or
replacing the Magnetron
• DO NOT touch any parts of the control panel circuit A
resulting static electric discharge may damage this
P C B
• NEVER operate the oven with no load
• NEVER injure the door seal and front plate of the oven
cavity
• NEVER put iron tools on the magnetron
• NEVER put anything into the latch hole and the
interlock switches area
• Proper operation of the microwave oven requires that
the magnetron be assembled to the waveguide and
cavity Never operate the magnetron unless it is
properly installed
• Be sure that the magnetr n gasket is pr perly
installed ar und the d me f the tube whenever
installing the magnetr n.
2-1
CAUTIONS
Unlike other appliances, the microwave oven is
high-voltage and high-current equipment
Though it is free from danger in ordinary use,
extreme care should be taken during repair
THE OVEN IS TO BE SERVICED ONLY
BY PROPERLY QUALIFIED SERVICE
PERSONNEL.
MICROWAVE RADIATION
Personnel should not be exposed to the
microwave energy which may radiate from the
magnetron or other microwave generating
device if it is improperly used or connection
All input and output microwave connections,
waveguide, flange and gasket must be secure
never operate the device without a microwave
energy absorbing load attached
Never look into an open waveguide or antenna
while the device is energized
Gasket
ANTENNA
COOLING FIN
MAGNETRON
CHASSIS GROUND
FILAMENT
TERMINALS
MAGNETRON

INSTALLATIONS
3-1
INSTALLING
1 Empty the microwave oven and clean inside it with
a soft, damp cloth Check for damage such as
misaligned door, damage around the door or dents
inside the cavity or on the exterior
2 Put the oven on a counter, table, or shelf that is
strong enough to hold the oven and the food and
utensils you put in it (The control panel side of the
oven is the heavy side Use care when handling )
3 Do not block the vent and the air intake openings
Blocking vent or air intake openings can cause
damage to the oven and poor cooking results
Make sure the microwave oven legs are in place to
ensure proper air flow
4 The oven should not be installed in any area where
heat and steam are generated, because they may
damage the electronic or mechanical parts of the
unit
Do not install the oven next to a conventional
surface unit or above a conventional wall oven
5 Use microwave oven in an ambient temperature
less than 104°F(40°C)
6 Place the microwave oven on a sturdy and flat
surface at least 10 cm(4 inches) from the wall
7 Place the microwave oven as far away as possible
from TV, RADIO, COMPUTER, etc , to prevent
interference
8 Do not touch the front glass during or after cooking
of the Grill and Combination mode
This glass is very hot during heater operating
9 Do not operate the oven at microwave and
combination mode with Grill rack placed in the
cavity when the oven is empty
EARTHING INSTRUCTIONS
This microwave oven is designed to be used in a fully
earthed condition
It is imperative, therefore, to make sure it is properly
earthed before servicing
WARNING-
THIS APPLIANCE
MUST BE EARTHED
IMPORTANT
As the colors of the wires in the mains lead of this
appliance may not correspond with the colored
markings identifying the terminals in your plug,
proceed as follows
The wire which is colored green-and-yell w must be
connected to the terminal in the plug which is marked
with the letter Eor by the earth symb l ( ) or
colored green or green-and-yell w
The wire which is colored blue must be connected to
the terminal in the plug which is marked with the letter
Nor colored black
The wire which is colored br wn must be connected
to the terminal in the plug which is marked with the
letter Lor colored red
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
10cm
The wires in this mains lead are colored in
accordance with the following code:
Green-and-yell w: Earth
Blue: Neutral
Br wn: Live

Display
Pads
Some items in display can be seen but will not glow
FEATURES
CONTROL PANEL
4-1
OPERATING INSTRUCTIONS

Window Door Screen
Electronic Control
Safety Door Lock System
TIME ENTRY Use to enter heating time without changing
preprogrammed number pads
Pads 1-0 Use to begin heating with preprogrammed
times and power levels or to enter times for
“Manual Time Entry” cooking
HOLD 0%, Use to select power level Oven can heat at
full or reduced power If oven power level is
set to 0% oven does not heat for
programmed time If no power level is
selected, oven operates at 100% power
STOP/RESET Use to exit programming mode and stop
cooking during cooking cycle
START Use to start “Manual Time Entry” program
or restart interrupted cooking cycle Use to
advance to next user option Use to save
times and power levels when programming
pads
DEFROST 20%,
MEDIUM 50%,
MED-HI 70%
DES11EA / US11EA

4-2
FEATURES
CONTROL PANEL
OPERATING INSTRUCTIONS

Window Door Screen
Electronic Control
Safety Door Lock System
DFS11EA / UFS11EA
Display
Some items in display can be seen but will not glow
Pads
Use to enter heating time without changing
preprogrammed number pads
Use to begin heating with preprogrammed
times and power levels or to enter times for
“Manual Time Entry” cooking
Use to select power level Oven can heat at
full or reduced power If oven power level is
set to 0% oven does not heat for
programmed time If no power level is
selected, oven operates at 100% power
Use to exit programming mode and stop
cooking during cooking cycle
Use to start “Manual Time Entry” program
Use to automatically increase the 
programmed time for double quantities
or restart interrupted cooking cycle Use to
advance to next user option Use to save
times and power levels when programming
pads
TIME ENTRY
Pads 1-0
POWER
LEVEL
STOP/RESET
START
QTY2x

4-3
FEATURES
CONTROL PANEL
OPERATING INSTRUCTIONS

Window Door Screen
Electronic Control
Safety Door Lock System
DECS11MA / UCS11MA
Display
Some items in display can be seen but will not glow
Pads
Use to enter cooking time
Use to begin heating with preprogrammed
times and power levels
Use to select power level Oven can heat at
full or reduced power
Use to start “Manual Time Entry” program
or restart interrupted cooking cycle Use to
advance to next user option Use to save
times and power levels when programming
pads
DIAL
QUICK SET
START
70%,
50%,
DEFROST


4-4
FEATURES
CONTROL PANEL
OPERATING INSTRUCTIONS

Window Door Screen
Electronic Control
Safety Door Lock System
DFS11G
Display
Some items in display can be seen but will not glow
Pads
Use to enter heating time without changing
preprogrammed number pads
Use to begin heating with preprogrammed
Use to enter times for “Manual Time Entry”
times and power levels or to enter times for
“Manual Time Entry” cooking
cooking
Use to select power level Oven can heat at
full or reduced power If oven power level is
set to 0% oven does not heat for
programmed time If no power level is
selected, oven operates at 100% power
Use to exit programming mode and stop
cooking during cooking cycle
Use to start “Manual Time Entry” program
Use to automatically increase the 
programmed time for double quantities
or restart interrupted cooking cycle Use to
advance to next user option Use to save
times and power levels when programming
pads
TIME ENTRY
DIAL
Pads 1-0
POWER
LEVEL
STOP/RESET
START
QTY2x

4-5
Cooking Displays
Shows when power is connected to oven Open and close
door to clear
READY shows when oven control will accept entries
Appears after oven door is opened and closed
33:33 shows heating time When more than 1 heating stage is
programmed, total time for all stages displays
COOK shows when oven is operating
20 indicates the microwave power level used If power level
does not show, oven is heating at 100% power
Cooking DisplaysCooking DisplaysCooking Displays
Programming Displays
Indicates programming mode See “Programming” section
of manual for programming procedure
Indicates programming user options mode See “User
Options” section of manual for programming procedure
Programming DisplaysProgramming DisplaysProgramming Displays

OPERATION
4-6
To avoid fire,do not dry newspapers or clothes in
microwave oven
CAUTION
Interrupting Operati n
• Open oven door to interrupt operation Oven fan
continues to operate Close door and press START
pad to resume oven operation
• Press STOP/RESET pad to interrupt operation
Display continues to show countdown time Press
START pad to resume oven operation and
countdown timing
Canceling Mistakes
• If oven is operating,press STOP/RESET pad once to
stop oven,then again to clear display
• If oven door is open and time shows in display,close
oven door and press STOP/RESET pad to clear
display
Operating Prepr grammed Pads
Oven has 10 ~ 20 preprogrammed number pads
Instructions are written for factory programmed ovens
Ovens that are reprogrammed can respond differently
than described below
1 Open oven door ,place food in oven,and close oven
door
• If pad is not pressed in 30 seconds,open and close
oven door again
2 Press desired number pad
• Oven operates and time counts down
3 Oven stops heating and oven signal sounds when
heating timing elapses
Operating QTY 2X Pads
1 Press Pad
2 Press desired number pad
• Example : press + =18 sec
QTY
2X
QTY
2X
1
2
3
4
5
6
7
8
9
0
10 sec
20 sec
30 sec
45 sec
1 min
1:30 min
2 min
3 min
4 min
5 min
01
02
03
04
05
06
07
08
09
10
Pads Pads Pads Heating
Times Heating Times Heating Times
Prepr grammed Times and C k Level
All preprogrammed pads arrive set at full power
Option: Single Digit
11
12
13
14
15
16
17
18
19
20
10 sec
20 sec
30 sec
45 sec
1 min
1:30 min
2 min
3 min
4 min
5 min
20 sec
40 sec
1 min
1:30 min
2 min
3 min
4 min
6 min
8 min
10 min
Option: Double Digit
Manual Time Entry
Manual Time Entry feature allows the operator to enter
time and power levels, and heat without changing the
preprogrammed pads
1 Open oven door, place food in oven, and close door
• Display shows "READY"
• If pad is not pressed in 30 seconds, open and close
oven door again
2 Press TIME ENTRY pad
• Display shows "00:00"
3 Press number pads to enter desired cooking time
• For example, to heat for 2 minutes 30 seconds,
press 2, 3, and 0 pads
4 Press desired power level pad to change power level
• If a power level pad is not pressed, oven defaults to
100% power
• For example, pressing MEDIUM 50% pad sets oven
to 50% power
• Display shows current power level if other than 100
percent power
5 Press START pad
• Oven operates and time counts down
6 Oven stops heating and oven signal sounds when
heating timing elapses

4-7
PROGRAMMING
Prepr grammed Number Pads
Oven has 10~20 preprogrammed number pads Follow
instructions below to program heating times and power
levels for customized cooking
1 Open oven door
• If door is closed or RESET pad is pressed before
finishing programming sequence, oven exits
programming mode
2 Press and hold pad 1for approximately 5 seconds
• After 5 seconds, signal sounds Display shows
“PROGRAM” indicating program mode
3 Press desired number pad
• Display shows heating time, “COOK LEVEL” and
power level if other than 100 percent power
4 Press number pads to enter desired cooking time
• For example, to heat for 2 minutes 30 seconds, press
2,3, and 0 pads
5 Press desired power level pad to change power level
• If a power level pad is not pressed, oven defaults to
100% power
• For example, pressing MEDIUM 50% pad sets oven to
50% power
• Display shows current power level if other than 100%
power
6 Press START pad to save new heating time and power
level in oven memory
• Repeat step 3-6 to program additional pads
7 Press RESET pad or close oven door to exit
programming mode
Multiple Heating Stages
Follow instructions below to program oven to perform 3
consecutive heating cycles without interruption
1 Open oven door
• If door is closed or RESET pad is pressed before
finishing programming sequence, oven exits
programming mode
2 Press pad 1for approximately 5 seconds
• After 5 seconds, signal sounds
3 Press desired number pad
• Display shows heating time and preprogrammed
number
4 Press number pads to enter desired cooking time
• For example, to heat for 2 minutes 30 seconds,
5 Press desired power level pad to change power
level
• If a power level pad is not pressed, oven defaults to
100% power
• For example, pressing MEDIUM 50% pad sets
oven to 50% power
• Display shows current power level if other than 100
percent power
6 Press TIME ENTRY pad
• Display briefly shows "STAGE 2" Then cook time
and power level for stage show in display
• Repeat steps 5-6 to create additional stages
7 Press START pad to save new heating time and
power level in oven memory
8 Press RESET pad or close oven door to exit
programming mode

4-8
User Opti ns
Follow the instructions below to customized the
microwave oven’s operation End-of-cycle signal,
maximum heating time and other options can be
changed to meeting your cooking needs
1 Open oven door
• If door is closed or RESET pad is pressed before
finishing programming sequence, oven exits
programming mode
2 Press and hold pad 2 for approximately 5 seconds
• After 5 seconds, signal sounds Display shows
“OPTION”
3 Press number pad that matches desired option
• “OP” represents optional program mode, first
number represents option number and second
number represents functions currently selected for
option
4 Press START pad to advance to next option See table
for options
5 Press number pad (0,1-3) to change option
6 Press START pad to save changes
• Repeat steps 4-6 to change additional options
7 Press STOP/RESET pad or close oven door to exit
programming mode
Optional Program
Indicator Pad Number Option Selected
Numbered Pads Display Opti ns (Fact ry Settings in B ld)
1
End f Cycle Beep
OP:10
OP:11
OP:12
3 sec nd beep.
Continuous beep until door is opened
5 beep bursts until door is opened
2
Speaker V lume
OP:20
OP:21
OP:22
OP:23
Eliminates beep
Sets volume to low
Sets volume to medium
Sets v lume t high.
3
Key Beep OP:30 OP:31 Prevents beep when pad is pressed All ws beep when pad is pressed.
4
Keyb ard Enable
Wind w
OP:40
OP:41
OP:42
OP:43
15 seconds after oven door is opened, keyboard disabled
30 seconds after oven door is opened, keyboard disabled
1 minute after ven d r is pened, keyb ard disabled.
2 minutes after oven door is opened, keyboard disabled
5
Add Time During
Heating
OP:50
OP:51 Prevents adding heating time while oven is heating
All ws heating time t be changed while ven is heating when a mem ry pad
is pressed.
6
Reset D r Open
OP:60
OP:61
All ws ven t resume heating time c untd wn after d r is pened during
cycle.
Cancels heating time count down after door is opened during cycle
7
(s me m dels)
Maximum Heating Time
OP:70
OP:71 All ws 60 minutes f heating time (s me m dels). Allows 10 minutes of heating time
8
Manual Operati n OP:80 OP:81 Allows use of preprogrammed pads only All ws use f manual time entry and prepr grammed pads.
9
(s me m dels)
D uble Digit Operati n
OP:90
OP:91
All ws 10 (0-9) prepr grammed pads.
Allows 100 (00-99) preprogrammed pads
0
Clean Filter Message OP:00 OP:01
OP:02
OP:03
Do not display message
Display message for 24 hours every 7 days
Display message for 24 hours every 30 days
Display message for 24 hours every 90 days

SCHEMATIC DIAGRAM
4-9

4-10
CIRCUIT DESCRIPTION
GENERAL DETAILS
• The low voltage transformer supplies the necessary
voltage to the micom controller when power cord is
plugged in
• When the door is closed, the primary switch is ON, the
secondary switch is ON, and the monitor switch opens
(contact COM and NO)
WHEN SELECTING COOKING POWER
LEVEL AND TIME
• The micom controller memorizes the function you set
• The time you set appears in the display window
• Each indicator light turns on to indicate that the stage
has been set
WHEN TOUCHING THE START PAD
• The coil of the relay is energized by the micom
controller
• Power input is supplied to the high voltage transformer
through the fuse to primary switch and realy 3 

• Stirrer fan rotates
• The fan motor rotates and cools the magnetron by
blowing the air (coming from the intake on the base-
plate)
• The air is also directed into the oven to exhaust the
vapor in the oven through the upper plate
• Cooking time starts counting down
• 3 3 volts AC is generated from the filament winding of
the high voltage transformer This 3 3 volts is applied to
the magnetron to heat the magnetron filament through
two noise-preventing choke coils
• A high voltage of approximately 2100 volts AC is
generated in the secondary of the high voltage
transformer which is increased by the action of the high
voltage diode and charging of the high voltage
capacitor
• The negative 4,000 Volts DC is applied to the filament
of the magnetron
WHEN THE OVEN IS SET AT ANY LEVEL
EXCEPT MAXIMUM.
• The micom controller controls the ON-OFF time of
relay 3 by the applied signal to vary the average output
power of microwave oven as POWER LEVEL
(refer to page 1-1)
• One complete cycle of relay 3 is 12
WHEN THE DOOR IS OPENED DURING
COOKING
• Both the primary switch and relay 3 cut off the primary
winding voltage of the high voltage transformer
• ON-OFF of relay 3 is coupled electrically with opening
and closing of the secondary switch
• When the door is opened, the secondary switch is
opened and when the door is closed, the secondary
switch is closed
• The cooking time stops counting down
• Relay stops functioning
• As the door is opened, if the contact of primary switch
and relay 3 and/or secondary switch fail to open, 

the monitor switch activation, which in turn stops magnetron
oscillation
the fuse opens due to the large current surge caused by
RELAY 3
FUSE
SWITCH
MICOM CONTROLLER
SECONDARY
SWITCH
SWITCH
MONITOR TRANS-
FORMER
H V
INTERLLOCK
PRIMARY
INTERLLOCK
N
L
H V
INTERLLOCK
RELAY 3 SWITCH
MICOM CONTROLLER
TRANS-
FORMER
SECONDARY
SWITCH
MONITOR
PRIMARY
SWITCH
INTERLLOCK
FUSE
N
L

NECESSARY TOOLS
Tools normally used for TV servicing are sufficient
Standard tools are listed below
• Diagonal pliers
• Long nose pliers
• Phillips screwdriver
• Flat blade screwdriver
• Wrench (size 5mm)
• Nutdriver (size 5mm)
• Adjustable wrench
• Soldering iron
• Solder
• Vinyl insulation tape
• Polishing cloth
CAUTIONS
• Be sure t check micr wave leakage pri r t
servicing the ven if the ven is perative pri r t
servicing.
• The service pers nnel sh uld inf rm the
manufacturer, imp rter, r assembler f any
certified ven unit f und t have a micr wave
emissi n level in excess f 5 mW/cm2and should
repair any unit found to have excessive emission levels
at no cost to the owner and should ascertain the cause
of the excessive leakage The service personnel
should instruct the owner not to use the unit until the
oven has been brought into compliance
• If the ven perates with the d r pen, the service
pers nnel sh uld:
- Tell the user n t t perate the ven.
- C ntact the manufacturer and CDRH
(Center f r Devices and Radi l gical Health)
immediately.
NOTE: Address n CDRH
Office of Compliance(HFZ-312)
Center for Devices and Radiological
Healthe 1390, Piccard Drive,
Rockville MD 20850
• The service personnel should check all surface and
vent openings for microwave leakage
• Check for microwave leakage after every servicing
The power density of the microwave radiation leakage
emitted by the microwave oven should not exceed
4 mW/cm2 Always start measuring of an unknown field
to assure safety for operating personnel from radiation
leakage
NECESSARY MEASURING INSTRUMENTS
• TESTER(VOLTS-DC, AC, Ohmmeter)
• Microwave survey meter
- Holaday HI-1500
HI-1501
- Narda 8100
8200
• Inch scale
• 600 cc non conductive material beaker (glass or plastic),
inside diameter: approx 8 5 cm(31/2 in )
• Cylindrical and made of borosilicate glass vessel
max thickness: 3 mm
outside diameter: approx 190mm
height: approx 90mm
• Glass thermometer: 100°C or 212°F (1 deg scale)
MEASURING MICROWAVE ENERGY
LEAKAGE
• P ur 275±15 cc f 20±5°C(68±9°F) water in a beaker
which is graduated t 600 cc, and place the beaker
n the center f the turntable.
• Set the energy leakage m nit r t 2,450 MHz and
use it f ll wing the manufacturer's rec mmended
test pr cedure t assure c rrect result.
• When measuring the leakage, always use the 2-inch
(5 cm) spacer supplied with the pr be.
• Operate the ven at its maximum utput.
• Measure the micr wave radiati n using and
electr magnetic radiati n m nit r by h lding the
pr be perpendicular t the surface being measured
M ve pr be al ng shaded area
Pr be scanning speed
Less than 2.5 cm/sec
( 1in/sec)
5-1
SERVICE INFORMATION
TOOLS AND MEASURING INSTRUMENTS
MICROWAVE LEAKAGE TEST

MEASUREMENT WITH OUTER CASE
REMOVED
• When you replace the magnetron, measure for
microwave energy leakage before the outer case is
installed and after all necessary components are
replaced or adjusted
Special care should be taken in measuring the
following parts (Circled area of below Fig )
- Around the magnetron
- The waveguide
MEASUREMENT WITH A FULLY
ASSEMBLED OVEN
• After all components, including the outer case, are fully
assembled, measure for microwave energy leakage
around the door viewing window, the exhaust opening,
and air inlet openings
• Microwave energy leakage must not exceed the values
prescribed below
NOTE: Leakage with the outer case removedless than
5 mW/cm2sq Leakage for a fully assembled
oven (Before the latch switch (primary) is
interrupted) with the door in a slightly opened
position-less than 2 mW/cm2sq
NOTES WHEN MEASURING
• Do not exceed meter full scale deflection
• The test probe must be removed no faster than
1 inch/sec (2 5 cm/sec) along the shaded area,
otherwise a false reading may result
• The test probe must be held with the grip portion of the
handle
A false reading may result if the operator's hand is
between the handle and the probe
• When testing near a corner of the door, keep the probe
perpendicular to the surface making sure the probe
horizontally along the oven surface, this may possibly
cause probe damage
RECORD KEEPING AND NOTIFICATION
AFTER MEASUREMENT
• After adjustment and repair of any microwave energy
interruption or microwave energy blocking device,
record the measured values for future reference Also
enter the information on the service invoice
• The microwave energy leakage should not be more
than 4 mW/cm2sq after determining that all parts are
in good condition, functioning properly and genuine
replacement parts which are listed in this manual have
been used
• At least once a year, have the electromagnetic energy
leakage monitor checked for calibration by its
manufacturer
5-2
WARNING : AVOID CONTACTING ANY
HIGH VOLTAGE PARTS

• Microwave power output measurement is made with
the microwave oven supplied at its rated voltage and
operated at its maximum microwave power setting with
a load of (1000±5) g of potable water
• The water is contained in a cylindrical borosilicate glass
vessel having a maximum material thickness of 3 mm
and an outside diameter of approximately 190mm
• The oven and the empty vessel are at ambient
temperature prior to the start of the test
• The initial temperature (T1) of the water is (10±2)°C It
is measured immediately before the water is added to
the vessel After addition of the water to the vessel,
the load is immediately placed on the center of the
ceramic plate which is in the lowest position and the
microwave power switched on
• The time T for the temperature of the water to rise by a
value ∆ T of (10±2)°K is measured, where T is the time
in seconds and ∆ T is the temperature rise The initial
and final water temperatures are selected so that the
maximum difference between the final water
temperature and the ambient temperature is 5°K
• The microwave power output P in watts is calculated
from the following formula :
5-3
CERAMIC PLATE
WATER LOAD
MEASUREMENT OF MICROWAVE POWER OUTPUT
P =
DISASSEMBLY AND ADJUSTMENT
is measured while the microwave generator is
operating at full power Magnetron filament heat-up
time is not included (about 3 sec)
• The water is stirred to equalize temperature throughout
the vessel, prior to measuring the final water
temperature
• Stirring devices and measuring instruments are
selected in order to minimize addition or removal of
heat
4187 x (∆T)
T
securing
screw
Remove the screw
Lift up and pull out control panel
A. OUTER CASE REMOVAL
1) Disconnect the power supply cord from the outlet
2) Remove the screws from the rear of the case
The outer case must be moved backward to be lifted
off
B. POWER SUPPLY CORD
1) Remove the outer case
2) Disconnect two terminals, and remove one screw of
the ground terminal
C. CONTROL PANEL ASSEMBLY RMOVAL
1) Open the door
3) Disconnect the leadwire from RELAY (RY3)
of the PCBSUBASS’Y
2) Remove the screw for securing the control panel
4) Disconnect the leadwire from connector (CN1) of the
PCB SUB ASS’Y
5) Lift up and pull out control panel assembly carefully
from the cavity
CAUTION: DISCHARGE THE HIGH VOLTAGE
CAPACITOR BEFORE SERVICING
(refer to page 2-1)

D. PCB ASSEMBLY REMOVAL
1) Remove the control panel assembly from the
cavity (Refer to control panel assembly removal
on previous page )
2) Remove screws which hold the PCB SUB ASS’Y to
the control panel
3) Disconnect the flat cable from the PCB SUB
ASS’Y and take off the PCB SUB ASS’Y
E. DOOR MAIN ASSEMBLY REMOVAL
1) Open the door
2) Remove the choke cover cap very carefully with a flat-
blade screwdriver
CAUTION : Be careful n t t damage d r seal plate
by screwdriver.
3) Lift up and push the door
NOTE:
1 After replacing the door, be sure to check that the
primary switch, monitor switch, and secondary switch
operate normally
2 After replacing the door, check for microwave energy
leakage with a survey meter Microwave energy must
be below the limit of 4 mW/cm2 (with a 275 ml water
load)
3 When mounting the door assembly to the oven
assembly, be sure to adjust the door assembly parallell
to the chassis Also adjust so the door has no play
between the inner door surface and oven frame
assembly If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven
5-4
Control Panel PCB Sub Asm
Remove door
Remove choke cover
Door seal plate
SpacerSpacerSpacerSpacer